Setup Instructions

ManualsBrandsToro ManualsRiding Products60in TITAN HD 2000 Series Riding Mower

FormNo.3421-130RevA

TITAN

HDSeriesRidingMower

ModelNo.AllModels

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removethemachinefromthecrate.

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Servicethehydraulicuid.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Servicingthebattery.

Nopartsrequired

–

Raisetherolloverprotectionsystem

(ROPS).

Nopartsrequired

–

Checkthegrassdeector.

Nopartsrequired

–

Removetheshippingstrap(s).

No.2lithiumormolybdenum-based

grease(purchaseseparately)

1tube

Checkthemachineforgrease.

Locknut(3/8inch)

Carriagebolt(3/8x2-1/4inches)

Installtherightbumper(reardischarge

modelsonly).

Nopartsrequired

–

Checkthemoweradjustment.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer(allmachines).

Operator'sManual

Engineowner'smanual(non-Toro

engines)

Operator-trainingmaterial

Key2

Registrationcard1

Deliverthemachinetothecustomer(all

machines).

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3421-130*A

Summary of content (12 pages)

PAGE 1
Form No. 3421-130 Rev A TITAN® HD Series Riding Mower Model No. All Models Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 12 13 14 Description Qty. Use No parts required – Remove the machine from the crate. No parts required – Add fuel to the machine. No parts required – Check the engine-oil level. No parts required – Service the hydraulic fluid. No parts required – Check the tire pressure.
PAGE 2
1 4 Removing the Machine from the Crate Servicing the Hydraulic Fluid No Parts Required No Parts Required Procedure Procedure If removing the machine from a metal crate, refer to the Dealer/Distributor Portal for further information. This machine is shipped filled with hydraulic fluid in the reservoirs. Check the expansion tank; if necessary, add Toro® HYPR-OIL™ 500 hydraulic fluid, as recommended in the Operator's Manual, to the FULL COLD line (Figure 1).
PAGE 3
5 Checking the Tire Pressure No Parts Required Procedure Pressure: 13 psi (90 kPa) Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the correct tire type and procedure. g236732 Figure 2 1. Ensure that the ground cable does not rub against the lower shock mount. 2. Ensure that the ground cable does not rub against the trailing arm.
PAGE 4
. 7 Raising the Rollover Protection System (ROPS) No Parts Required Procedure 1. 2. Pull both knobs out and rotate them 90 degrees so that they are not engaged (Figure 3). Raise the roll bar to the operating position and rotate the knobs until they move partially into the grooves (Figure 3). g035064 Figure 3 1. Roll bar in the upright position 2. ROPS knob in the latched position 3. Pull the ROPS knob out. 4. Rotate the ROPS knob 90 degrees. 5. ROPS knob in the unlatched position 3.
PAGE 5
8 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. g021181 WARNING Figure 4 An uncovered discharge opening could allow the machine to throw objects toward you or bystanders, resulting in serious injury or death. Also, contact with the blade could occur. Never operate the machine without a cover plate, a mulch plate, grass deflector, or bagger installed. 1.
PAGE 6
9 10 Removing the Shipping Strap(s) Checking the Machine for Grease No Parts Required Parts needed for this procedure: 1 tube Procedure Note: This procedure is only for machines with a MyRide™ suspension system. No. 2 lithium or molybdenum-based grease (purchase separately) Procedure Before you use the machine, check the machine for grease; refer to Lubrication in the Operator's Manual. WARNING The springs are compressed by the shipping strap(s).
PAGE 7
11 12 Installing the Right Bumper Checking the Mower Adjustment Rear-Discharge Machines Only No Parts Required Parts needed for this procedure: 3 Locknut (3/8 inch) 3 Carriage bolt (3/8 x 2-1/4 inches) Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as needed.
PAGE 8
13 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower deck. Check the engine-oil level. Check the hydraulic-fluid level. Check that the ROPS is secure.
PAGE 9
14 Delivering the Machine to the Customer (All Machines) Parts needed for this procedure: 1 Operator's Manual 1 Engine owner's manual (non-Toro engines) 1 Operator-training material 2 Key 1 Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No. Dealer Initial Serial No.
PAGE 10
Dealer Initial Customer Initial Check Procedure Refer to the Operator's Manual to point out safety procedures, operation, and maintenance procedures. Review the warranty statement as shown in the Operator's Manual. Describe the post-sale service procedures for your store. Assist the customer in filling out and mailing the registration card or register online at www.Toro.com.
PAGE 11
Notes:
PAGE 12