Form No. 3371-907 Rev A GrandStand® Mower With 36in or 40in TURBO FORCE® Cutting Unit Model No. 74534—Serial No. 312000001 and Up Model No. 74536—Serial No. 312000001 and Up Model No. 79534—Serial No. 312000001 and Up Model No. 79536—Serial No. 312000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This spark ignition system complies with Canadian ICES-002. Important: This engine is not equipped with a spark arrester muffler. It is a violation of California Public Resource Code Section 4442 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land.
Operation................................................................... 14 Adding Fuel ....................................................... 14 Checking the Engine Oil Level............................ 15 Breaking In a New Machine ................................ 15 Think Safety First ............................................... 15 Operating the Parking Brake ............................... 15 Operating the Mower Blade Control Switch (PTO) ..........................................................
Safety – Use only an approved container – Never remove gas cap or add fuel with engine running. Allow engine to cool before refueling. Do not smoke. Note: The addition of attachments made by other manufacturers that do not meet American National Standards Institute certification will cause noncompliance of this machine. – Never refuel or drain the machine indoors. • Check that operator's presence controls, safety switches and shields are attached and functioning properly.
Toro Mower Safety • Look behind and down before backing up to be sure of a clear path. • Keep pets and bystanders away. • Slow down and use caution when making turns and crossing roads and sidewalks. Stop blades if not mowing. • Be aware of the mower discharge direction and do not point it at anyone. • Do not operate the mower under the influence of alcohol or drugs. • Use care when loading or unloading the machine into or from a trailer or truck.
goes over the edge of a cliff or ditch, or if an edge caves in. • Use extra care with grass catchers or other attachments. These can change the stability of the machine. • Keep all movement on slopes slow and gradual. Do not make sudden changes in speed or direction. • Mow slopes side to side. • Do not mow slopes greater than 20 degrees. Service • Never store the machine or fuel container inside where there is an open flame, such as near a water heater or furnace.
Slope Indicator G011841 Figure 2 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 20 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 20 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Battery Symbols Some or all of these symbols are on your battery 93-7010 1. Thrown object hazard—keep bystanders a safe distance from the machine. 2. Thrown object hazard, mower—keep the deflector in place. 3. Cutting/dismemberment of hand or foot—stay away from moving parts. 1. Explosion hazard 6.
110-2067 116-3267 115-4186 1. Interval 2. Power Take-off (PTO) 116-3290 3. Parking brake 4. Neutral 5. Operator presence switch 6. Battery 115-4212 1. Hydraulic oil level 3. Warning—do not touch the hot surface. 119-0185 2. Read the Operator's Manual.
119-0217 1. Warning—stop the engine; stay away from moving parts; keep all guards and shields in place. 119-1854 1. Adjustment knob for traction drive speed. 119-0186 36in Mower Deck 1. Belt routing 119-2317 1. Height-of-cut (inches) 119-0187 40in Mower Deck 1.
7-0454 1. Traction control 3. Slow 5. Reverse 2. Fast 4. Neutral 6. Power Take-off (PTO)—disengage 7. Operator presence switch 117–3626 1. Warning—read the Operator's Manual. 5. Thrown object hazard—keep bystanders a safe distance from the machine. 2. Warning—do not operate this machine unless you are trained. 6. Warning—engage the parking brake, stop the engine and remove the spark plug wire before performing any maintenance on the machine. 7.
Product Overview 6 5 7 4 8 9 10 11 12 3 2 g012564 1 Figure 4 Figure 3 1. Fuel cap 7. Hour meter 2. Height-of-cut lever 8. Choke 1. Side discharge chute 7. Manual tube 2. Battery 8. Platform (down position) 3. Blade control switch (PTO) 9. Ignition switch 9. Hydraulic tank 4. Right motion control lever 10. Speed control lever 3. Engine 4. Fuel tank 5. Controls 6. Motion control levers 10. Mower deck 11. Front caster wheel 12. Operator cushion 5. Left motion control lever 11.
Attachments/Accessories A selection of Toro approved attachments and accessories are available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. Specifications Figure 5 1. Safety interlock symbols 3. Hour meter Note: Specifications and design are subject to change without notice. 2.
Operation DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Checking the Engine Oil Level Note: A fuel stabilizer/conditioner is most effective when mixed with fresh gasoline. To minimize the chance of varnish deposits in the fuel system, use fuel stabilizer at all times. Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking Oil Level in Engine Maintenance. Filling the Fuel Tank Note: Determine the left and right sides of the machine from the normal operating position.
g012782 Figure 9 Figure 7 1. Parking brake engaged 2. Parking brake released • Move the motion control levers to neutral and move the right side motion control lever into the neutral lock position. Releasing the Parking Brake Push the parking brake lever forward. Operating the Mower Blade Control Switch (PTO) The blade control switch (PTO) is used in conjunction with the right side motion control lever to engage and disengage the mower blades.
Using the Speed Control Lever This machine has a speed control lever that sets the maximum ground speed of the machine. This can be adjusted to the operator's desired speed. It is recommended to use the slowest speed for new operator's. 1 Note: The numbers next to the speed control are an approximate miles per hour (mph) the machine will travel. 1. Move the speed control lever to set the desired speed. • Full forward has quick response and maximum speed.
g012703 1 2 Figure 16 7. Turn the ignition key to the Start position (Figure 13). When the engines starts, release the key. G008948 Figure 15 1. On Important: Do not engage starter for more than 5 seconds at a time. If the engine fails to start allow a 15 second cool-down period between attempts. Failure to follow these instructions can burn out the starter motor. 2.
Stopping the Engine The Safety Interlock System CAUTION CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. If safety interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. • Do not tamper with the interlock switches. • Check the operation of the interlock switches daily and replace any damaged switches before operating the machine.
Operating the Machine with the Platform Up 3. Move the right side motion control lever to the center, un-locked position. The blades should not rotate. 4. Move the motion control levers forward. The engine should kill. 5. Start the engine and release the parking brake. 6. Move the right side motion control lever to the center, un-locked position. 7. Continue holding the right side motion control lever in the center, un-locked position and pull up on the blade control switch (PTO) and release.
2 4 1 3 5 2 4 Figure 20 1. Platform up g012570 Figure 21 3. Pull the knob out to release the platform 2. Platform down 1. Front reference bar 4. Right control lever 2. Left control lever 5. Right control lever in the neutral lock position 3. Rear reference bar Driving Forward or Backward 4. Slowly push the motion control levers forward (Figure 22). The throttle control regulates the engine speed as measured in rpm (revolutions per minute).
Set the parking brake when you leave the machine; refer to Setting the Parking Brake in Operation. Remember to remove the key from the ignition switch. CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. Pushing the Machine by Hand The by-pass valves allow the machine to be pushed by hand without the engine running.
5. Stop the engine, remove the key, set the brake, and close the fuel valve. 6. Use the metal tie down loops on the machine to securely fasten the machine to the trailer or truck with straps, chains, cable, or ropes (Figure 25). Figure 24 Figure 25 1. Pump by-pass valve 1. Traction unit tie down loop 4. Release the parking brake. Loading Machines 5. Push the machine to the desired location. 6. Set the parking brake. Use extreme caution when loading units on trailers or trucks.
Important: Do Not attempt to turn the unit while on the ramp; you may lose control and drive off the side. Side Discharging or Mulching the Grass Avoid sudden acceleration when driving up a ramp and sudden deceleration when backing down a ramp. Both maneuvers can cause the unit to tip backward. This mower has a hinged grass deflector that disperses clippings to the side and down toward the turf.
Positioning the Flow Baffle The following figures are only recommendations for use. Adjustments will vary by grass type, moisture content, and height of grass. Note: If the engine power draws down and the mower ground speed is the same, open up the baffle. Position A This is the full rear position (see Figure 29). The suggested use for this position is a follows. • Use for short, light grass mowing conditions. Figure 27 1. Height-of-cut holes • Use in dry conditions. 3.
Note: Contact an Authorized Service Dealer to order a Weight Kit. WARNING Excessive weight changes can effect handling and operation of the machine. This could cause serious injury to you or bystanders. Make weight changes in small increments only. Evaluate the mower after each weight change to ensure the machine can be operated safely. G012678 Figure 30 Position C This is the full open position. The suggested use for this position is as follows (Figure 31). • Use in tall, dense grass mowing conditions.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. • Check the hydraulic fluid level. • Change the hydraulic filter. Before each use or daily • • • • • • Check the safety interlock system. Check the engine oil level. Clean the air intake screen. Check the brakes. Inspect the blades. Clean the mower deck.
Premaintenance Procedures Raising the Mower for Access The front of the mower can be raised and supported on its back for access under the machine for maintenance. 1. Raise the platform. Refer to Operating the Platform in Operation. 2. Remove the battery. Figure 33 1. Cap 3. Hydraulic tank 2. Piece of plastic 5. With two people, raise the front of the mower so it rests on the drive tires and the platform in the up position. 6. Perform any maintenance on the machine. 7.
1 2 3 4 g012572 Figure 35 Figure 34 1. Remove battery 2. With two people, lift the front end of the mower (ensure the platform is up) Release the Cushion for Rear Access The cushion can be released for rear access to the machine for maintenance or adjustment. 1. Lower the platform. 2. Remove the hairpin cotter pins on each side of the cushion. 3. Slide the large washers with plastic bushings to the inside. 4. Remove the cushion and lower it to the platform. 5.
Lubrication Grease with No. 2 general purpose lithium base or molybdenum base grease. Lubricate the speed/traction control linkage with a dry lubricant, PTFE (Polytetrafluoroethylene) (Figure 39). How to Grease 1. Disengage the PTO and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Figure 37 40in Mower Deck 3. Clean the grease fittings with a rag. Make sure to scrape any paint off the front of the fitting(s). 4.
Figure 40 1. Seal guard 2. Spacer nut with wrench flats 2. Remove the caster wheel from the caster forks. 3. Remove the seal guards from the wheel hub. 4. Remove one of the spacer nuts from the axle assembly in the caster wheel. Note that thread locking adhesive has been applied to lock the spacer nuts to the axle. Remove the axle (with the other spacer nut still assembled to it) from the wheel assembly. Figure 39 Greasing the Front Caster Pivots 5.
Engine Maintenance 13. Torque the nut to 75-80 in-lb (8-9 N-m), loosen, then re-torque to 20-25 in-lb (2-3 N-m). Make sure axle does not extend beyond either nut. Servicing the Air Cleaner 14. Reinstall the seal guards over the wheel hub and insert wheel into caster fork. Reinstall caster bolt and tighten nut fully. Service Interval/Specification Important: To prevent seal and bearing damage, check the bearing adjustment often. Spin the caster tire.
Cleaning the Foam Air Cleaner Element Note: There are different oil capacities for the different models listed in this manual. Ensure the correct amount of oil is used. Service Interval: Every 25 hours 1. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly. Important: Remember to add 80% of the oil and then gradually fill it to the full mark on the dipstick. 2. Dry the element by squeezing it in a clean cloth.
3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position (Figure 44). 1 3 6 2 4 1 2 3 4 5 7 g012596 Figure 44 8 9 4. Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 45). 10 G008792 Figure 43 Changing the Engine Oil Note: Dispose of the used oil at a recycling center. 1.
1 2 3 4 5 6 1 2 3 4 G008796 Figure 45 5 6 Changing the Engine Oil Filter Note: Change the engine oil filter more frequently when operating conditions are extremely dusty or sandy. 1. Drain the oil from the engine; refer to Changing the Engine Oil. 3/4 2. Place a rag under the oil filter to soak up any spilled oil. G012845 Figure 46 Important: Spilled oil may drain under the engine and onto the clutch.
Removing the Spark Plug 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Figure 49 Figure 47 Checking the Spark Plug Important: Never clean the spark plug(s). Always replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, or cracks.
Fuel System Maintenance Servicing the Fuel Filter Draining the Fuel Tank Service Interval: Yearly Note: There is no other recommended way to drain fuel from the tank, other than using a syphon pump. A syphon pump can be purchased at a hardware store. Never install a dirty filter if it is removed from the fuel line. Replacing the Fuel Filter Note: Note how the fuel filter is installed in order to install the new filter correctly. DANGER Note: Wipe up any spilled fuel.
Electrical System Maintenance WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Servicing the Battery • Always Disconnect the negative (black) battery cable before disconnecting the positive (red) cable. Service Interval: Every 100 hours Always keep the battery clean and fully charged. Use a paper towel to clean the battery case.
2 3 Note: Do not run the machine with the battery disconnected, electrical damage may occur. 4 1 5 Figure 53 1. Positive Battery Post 3. Red (+) Charger Lead 2. Negative Battery Post 4. Black (-) Charger Lead Servicing the Fuses The electrical system is protected by fuses. It requires no maintenance. If a fuse blows, check the component or circuit for a malfunction or short. 6 g013199 1. Release the operator cushion from the rear of the machine. Figure 52 1. Wing nut 4.
Drive System Maintenance 1 2 Adjusting the Tracking Note: Determine the left and right sides of the machine from the normal operating position. 1. Push both control levers forward the same distance. 2. Check if the machine pulls to one side. If it does, stop the machine and set the parking brake. 3. Release the cushion from the rear of the machine. 4. Rotate the right cable adjustment to position the right motion control in the center of the control panel neutral lock slot (Figure 56).
4. If adjustment is needed, loosen the jam nut and adjust the bolt to the correct distance. Tighten the jam nut after adjusting the bolt (Figure 57). 5. Test the safety interlock system before operation. 1 6 Figure 58 Adjusting the Caster Pivot Bearing Service Interval: Every 500 hours/Yearly (whichever comes first) 2 3 4 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 2.
Figure 60 1. Adjusting nut 2. Slot Figure 59 1. Spring Washers 3. Dust Cap 2. Lock Nut Adjusting the Electric Clutch Service Interval: Every 500 hours—Check the electric clutch. The clutch is adjustable to ensure proper engagement and proper braking. 1. Insert a 0.015–0.021 inch (0.381–0.533 mm) feeler gauge through one inspection slot in the side of the assembly. Make sure it is between the armature and the rotor friction surfaces. The gap needs to be at least .015 inches (0.381 mm) and not more than .
Cooling System Maintenance 1 2 Cleaning the Air Intake Screen Service Interval: Before each use or daily 3 Before each use remove any build-up of grass, dirt or other debris from the cylinder and cylinder head cooling fins, air intake screen on flywheel end, and carburetor-governor levers and linkage. This will help insure adequate cooling and correct engine speed and will reduce the possibility of overheating and mechanical damage to the engine.
Brake Maintenance Adjusting the Brakes If the gap between the brake bar and tire is not correct, an adjustment is required. Servicing the Brake 1. Park the machine on a level surface, disengage the PTO, and set the parking brake. Before each use, check brakes on both a level surface and slope. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Always set the parking brake when you stop the machine or leave it unattended.
Belt Maintenance Replacing the Mower Deck Belts for 40in Mowers Checking the Belts Replacing the Right Mower Deck Belt Service Interval: Every 100 hours—Check the pump drive belt. 1. Disengage the PTO and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Unlatch and remove the right belt cover. 4. Remove the spring from the anchor post on the idler pulley arm (Figure 64). 5. Remove the worn mower belt (Figure 64).
5. Remove the spring from the anchor post on the idler pulley arm (Figure 64). 6. Remove the worn mower belt (Figure 64). 7. Install the new mower belt around the deck pulleys, clutch pulley and idler pulley (Figure 64 ). 8. Install the spring onto the anchor post (Figure 64 ). 9. Install the right mower belt. Refer to Replacing the Right Mower Belt. 10. Install the belt covers onto the cutting unit and secure the latches. Figure 67 4. Clutch retainer 2. Idler pulley 5. Pump drive belt 3.
Controls System Maintenance 1 2 Adjusting the Motion Control Handle Positions Adjusting the Right Side Motion Control Lever If the motion control levers do not align horizontally, adjust the right side motion control lever. 3 Note: Adjust the horizontal alignment before the front to back alignment. 1. Disengage the PTO, move the right side motion control lever to the neutral position and set the parking brake. G012704 Figure 69 2.
2 1 3 3 1 2 4 G012706 Figure 71 1. Left motion control lever 3. Neutral locked position 2. Right motion control lever 4. Align the control levers front to back 2. Ensure the right motion control lever moves easily into the neutral lock position. Note: Turn the cable adjustment clockwise to move the motion control handle forward. Turn the cable adjustment counter-clockwise to move the motion control handle rearward. 3. Rotate the cable adjustment on right side when adjustment is needed.
Hydraulic System Maintenance Servicing the Hydraulic System Hydraulic Oil Type: Toro® HYPR-OIL™ 500 hydraulic oil or Mobil® 1 15W-50 synthetic motor oil. Important: Use oil specified or equivalent. Other fluids could cause system damage. Hydraulic System Oil Capacity: 67 oz. (2.0 l) Checking the Hydraulic Fluid Service Interval: After the first 8 hours Every 50 hours Figure 72 1. Left cable adjustment 3.
5. Remove cap from filler neck. Look inside to check the fluid level in the reservoir. (Figure 73). 2. Stop the engine and wait for all moving parts to stop before leaving the operating position. 6. Add fluid to the reservoir until it reaches the cold level of the baffle. 3. Remove hydraulic reservoir cap. 4. Locate the front hydraulic hose under the hydraulic tank and place drain pan under the tank (Figure 74). 7.
Replacing the Hydraulic Filter Service Interval: After the first 8 hours Every 500 hours/Yearly (whichever comes first) WARNING Hot hydraulic fluid can cause severe burns. Allow the hydraulic fluid to cool before performing any maintenance to the hydraulic system. Figure 76 1. Disengage the PTO and set the parking brake. 1. Hydraulic filter 2. Stop the engine and wait for all moving parts to stop before leaving the operating position. 3. Adapter 2.
Mower Deck Maintenance Checking the Hydraulic Lines Service Interval: Every 100 hours Check hydraulic hoses and hoses for leaks, loose fittings, kinked hoses, loose mounting supports, wear, weather and chemical deterioration. Make necessary repairs before operating. Servicing the Cutting Blades To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, you may want to keep extra blades on hand.
Checking for Bent Blades performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Rotate the blades until the ends face forward and backward.
4. Check the tire pressure of both drive tires. If needed, adjust to 13 psi (90 kPa) 5. Lower the mower to the 3 inch (76 mm) height-of-cut position. Figure 81 1. Blade Note: The actual cutting height will not be adjusted until the deck has been leveled. Refer to Adjusting Height of Cut. 2. Balancer 6. Check the distance between the swivels, measure at the center of the swivels (center-to-center length) on the threaded rod. This length needs to be 19-1/2 inches (49.
6. Use the adjustment bolt to achieve 1/4 to 3/8 inch (6 to 10 mm) lower in front at A than in the rear at B (Figure 83). 1 7. Tighten the nut on the upper chain bolt and the jam nut on the adjustment bolt. A B 2 3 2 5 6 7 8 g012784 Figure 84 4 1. Measure here from the blade to a hard surface 2. Measure at A and B g012739 Figure 83 1. Measure here at the center of the swivels (center-to-center length) 5. Rear chain 2. Swivel jam nuts 6. Adjustment bolt 3. Front swivel 4. Front chain 7.
C A C D g012787 g012788 Figure 85 1. Measure here from blade to hard surface Figure 86 2. Measure at A and C 1. Measure here from blade to hard surface Adjusting the Right Side Front-to-Rear Mower Pitch 2. Measure at C and D Adjusting the Height of Cut 1. Lower the mower to the 3 inch (76 mm) height-of-cut position. 1. Position the right blade front-to-rear (Figure 86). 2. Position the left blade front-to-rear (Figure 85). 2.
1 4 3 2 g012783 Figure 87 1. Jam nut Figure 88 3. Groove indicating left hand threads 1. 10-1/8 inch (25.7 cm) for 40in mower decks and 11-1/8 inch (28.2 cm) for 36in mower decks 2. Spring jam nut 2. Turnbuckle 3. Front nut 4. Compression spring Adjusting the Compression Spring Note: Adjusting the compression spring will alter how much the deck will float and how much effort it takes to lift the deck when using the height-of-cut handle.
6 2 4 Cleaning 7 Cleaning Under the Mower 3 Service Interval: Before each use or daily Remove the grass buildup under the mower daily. 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 1 5 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. g015594 Figure 89 1. Bolt 5. Spring installed 2. Spacer 6. Grass Deflector 3. Locknut 7. J hook end of spring 3.
Storage hole. Now use the starter to crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s). Cleaning and Storage 10. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged or defective. 1. Disengage the power take off (PTO), set the parking brake, and turn the ignition key to off. Remove the key. 11. Paint all scratched or bare metal surfaces.
Troubleshooting Problem Engine will not start, starts hard, or fails to keep running. Engine loses power. Engine overheats. Machine does not drive. Possible Cause 1. Fuel tank is empty or shut-off valve closed. 1. Fill fuel tank with gasoline and open valve 2. Choke is not on. 3. Spark plug wire is loose or disconnected. 4. Spark plug is pitted, fouled, or the gap is incorrect. 5. Air cleaner is dirty. 6. Dirt in the fuel filter. 7. Dirt, water, or stale fuel is in the fuel system. 8.
Problem Blades do not rotate. Possible Cause 1. Pump drive belt is worn, loose or broken. 1. Check the belt tension. 2. Pump drive belt is off pulley. 2. Install drive belt and check adjusting shafts and belt guides for correct position. 3. Install new deck belt. 3. Mower deck belt is worn, loose or broken. 4. Mower deck belt is off pulley. 5. 6. 7. 8. 9. Broken or missing idler spring. Electric clutch out of adjustment. Clutch connector or wire damaged. Damaged electric clutch.
Schematics Hydraulic Schematic (Rev.
G015606 Electrical Schematic (Rev.
The Toro Total Coverage Warranty A Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship. The following time periods apply from the date of purchase by the original owner: Products 21 in.
