Form No. 3388-820 Rev A GrandStand® Mower With 122cm TURBO FORCE® Cutting Unit Model No. 74568TE—Serial No. 315000001 and Up g015545 Register at www.Toro.com.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
Contents Servicing the Fuses .................................................41 Drive System Maintenance .........................................41 Adjusting the Tracking ...........................................41 Checking the Tire Pressure ......................................43 Adjusting the Caster-Pivot Bearing............................43 Servicing the Caster Wheels and Bearings...................43 Adjusting the Electric Clutch....................................44 Cooling System Maintenance ..
Preparation Safety • Evaluate the terrain to determine what accessories and Improperly using or maintaining this mower can result in injury. To reduce the potential for injury, comply with these safety instructions. • Toro designed and tested this mower for reasonably safe service; however, failure to comply with the following instructions may result in personal injury.
• Do not change the engine governor setting or overspeed • If fuel is spilled on clothing, change your clothing the engine. immediately. • Stop on level ground, disengage drives, engage the • Do not overfill fuel tank. Replace fuel cap and tighten parking brake (if provided), shut off the engine before leaving the operator's position for any reason, including emptying the catchers or unclogging the chute. securely.
Toro Mower Safety Slope Operation The following list contains safety information specific to Toro products and other safety information you must know. All slopes and ramps require extra caution. If you feel uneasy on a slope, do not mow it. • Remove obstacles such as rocks, tree limbs, etc. from the This product is capable of amputating hands and feet, and throwing objects. Always follow all safety instructions to avoid serious injury or death. mowing area. • Watch for holes, ruts or bumps.
Sound Pressure This unit has a sound pressure level at the operator’s ear of 93 dBA, which includes an Uncertainty Value (K) of 1 dBA. The sound pressure level was determined according to the procedures outlined in EN ISO 5395:2013. Sound Power This unit has a guaranteed sound power level of 105 dBA, which includes an Uncertainty Value (K) of 1 dBA. The sound power level was determined according to the procedures outlined in ISO 11094. Vibration Level Hand-Arm Measured vibration level for right hand = 1.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 20 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 20 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7818 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115-149 N-m (85-110 ft-lb). 115-4212 1. Hydraulic oil level 3. Warning—do not touch the hot surface. 2. Read the Operator's Manual. 106-5517 1. Warning–Do not touch the hot surface. 116-8772 115-4186 1.
119-0217 1. Warning—stop the engine; stay away from moving parts; keep all guards and shields in place. 120-6412 119-7247 1. Height of cut (HOC)—high 1. Belt tension adjustment; read the Operator's Manual for more information. 3. Height of cut (HOC)—low 119-8663 2. Height of cut (HOC)—medium >10∞ >20∞ 121-6049 119-8663 1. Thrown object hazard—keep bystanders away from the machine. 1.
Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. Battery Symbols Some or all of these symbols are on your battery 131-1180 1. Read the Operator's Manual. 2. Short, light grass; dry conditions; maximum dispersion 3. Bagging setting 4. Tall, dense grass; wet conditions; maximum ground speed 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7.
119-7285 1. Read the Operator's Manual before performing any maintenance. 3. Lubricate every 50 hours 5. Check the hydraulic oil every 50 hours 2. Check the drive wheel tire pressure every 50 hours 4. Lubricate the caster wheel every 500 hours 6. Check the engine oil every 8 hours 119-8727 1. Traction control 3. Slow 5. Reverse 2. Fast 4. Neutral 6. Power Take-off (PTO)—disengage 12 7.
120-6464 1. Parking brake—engage 3. Power Take-off (PTO)—engage 5. Engine speed 7. Continuous variable setting 2. Parking brake—disengage 4. Power Take-off (PTO)—disengage 6. Fast 8.
Product Overview 3 5 4 6 7 8 13 12 9 11 10 g015230 Figure 5 G017850 Figure 4 1. Side-discharge chute 6. Control levers 2. Battery 7. Platform (down position) 3. Engine 8. Hydraulic tank 4. Fuel tank 5. Controls 1. Parking-brake lever 9. Mower deck 10. Front caster wheel 8. Height-of-cut pin 2. Choke 3. Hour meter 4. Ignition switch 9. Platform latch 10. Throttle control 11. Right motion-control lever 5. Fuel gauge 12. Blade-control switch (PTO) 6. Height-of-cut lever 13.
Battery-Indicator Light Attachments/Accessories If the ignition key is turned to the On position for a few seconds, the battery voltage will be displayed in the area where the hours are normally displayed. A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories.
Operation DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Breaking in a New Machine of varnish deposits in the fuel system, use fuel stabilizer at all times. New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance. Filling the Fuel Tank Note: Do not fill the fuel tank completely full. Fill the fuel tank to the bottom of the filler neck.
Operating the Mower-Blade-Control Switch (PTO) Operating the Parking Brake Always set the parking brake when you stop the machine or leave it unattended. Before each use, check the parking brake for proper operation. The blade-control switch (PTO) is used in conjunction with the right side motion-control lever to engage and disengage the mower blades. If the parking brake does not hold securely, adjust it; refer to Servicing the Brake (page 45).
Operating the Throttle Operating the Ignition Switch 1. Turn the ignition key to the Start position (Figure 14). When the engines starts, release the key. The throttle control can be moved between Fast and Slow positions (Figure 12). Important: Do not engage starter for more than 5 seconds at a time. If the engine fails to start allow a 15 second cool-down period between attempts. Failure to follow these instructions can burn out the starter motor.
Using the Fuel Shut-off Valve Close the fuel shut-off valve for transport, maintenance, and storage (Figure 15). Ensure the fuel shut-off valve is open when starting the engine. g015365 1 Figure 16 7. Turn the ignition key to the Start position (Figure 17). When the engines starts, release the key. 2 Important: Do not engage the starter for more than 5 seconds at a time. If the engine fails to start, allow a 15 second cool-down period between attempts.
Stopping the Engine The Safety-Interlock System CAUTION CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. If safety-interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. • Do not tamper with the interlock switches.
Testing the Safety-Interlock System WARNING Service Interval: Before each use or daily The operator platform is heavy and may cause injury when lowering and raising the operator platform. The platform may suddenly drop if not supported when the latch pin is pulled out. Test the safety-interlock system before you use the machine each time. Note: If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately.
Driving Forward 1. Release the parking brake; refer to Releasing the Parking Brake (page 18). 2. Move the right side motion-control lever to the center, unlocked position. 1 2 3 4 3 5 4 G012182 Figure 21 Figure 20 1. Platform up 3. Pull the knob out to release the platform. 1. Front reference bar 4. Right control lever 2. Left control lever 5. Right control lever in the neutral lock position 3. Rear reference bar 2. Platform down 3.
Stopping the Machine To stop the machine, move the motion control levers to neutral, move the right side motion control lever into the neutral lock position, disengage the power take off (PTO), and turn the ignition key to off. Set the parking brake when you leave the machine; refer to Setting the Parking Brake (page 18). Remember to remove the key from the ignition switch. CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended.
Pushing the Machine by Hand Transporting the Machine The bypass valves allow the machine to be pushed by hand without the engine running. Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Important: Always push the machine by hand. Do not tow the machine, because hydraulic damage may occur. To transport the machine: 1.
Side Discharging or Mulching the Grass unit to tip backward. If loading on or near a slope, position the trailer or truck so it is on the down side of the slope and the ramp extends up the slope. This will minimize the ramp angle. The trailer or truck should be as level as possible. This mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. Important: Do not attempt to turn the unit while on the ramp; you may lose control and drive off the side.
Adjusting the Flow Baffle Positioning the Flow Baffle The mower-discharge flow can be adjusted for different types of mowing conditions. Position the cam lock and baffle to give the best quality of cut. The following figures are only for recommended use. Adjustments will vary by grass type, moisture content, and the height of the grass. 1. Disengage the PTO, move the motion-control levers to the neutral-locked position, and set the parking brake.
Position B Using the Mid-Size Weight Use this position when bagging (Figure 31). • Weights are installed to improve handling, balance, and improve performance. Weights can be added or removed to create optimized performance under different mowing conditions and for operator preference. • It is recommended that weights be added or removed one at a time until the desired handing and balance is achieved. Note: Contact an Authorized Service Dealer to order a Weight Kit.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. • Check the hydraulic fluid level. • Change the hydraulic filter. Before each use or daily • • • • • • Check the safety-interlock system. Check the engine-oil level. Clean the air-intake screen. Check the brakes. Inspect the blades. Clean the mower deck.
Premaintenance Procedures Raising the Mower for Access The front of the mower can be raised and supported on its back for access under the machine for maintenance. 1. Raise the platform; refer to Operating the Platform (page 22). 2. Remove the battery. Figure 34 1. Cap 3. Hydraulic tank 2. Piece of plastic 5. With 2 people, raise the front of the mower so that it rests on the drive tires and the platform in the up position. 6. Perform any maintenance on the machine. 7.
Figure 35 1. Remove battery 2. Front end of the mower Figure 36 1. Plastic bushing with the large washer Releasing the Cushion for Rear Access 2. Cushion bracket with the key hole You can release the cushion for rear access to the machine for maintenance or adjustment. 1. Lower the platform. 2. Remove the hairpin-cotter pins on each side of the cushion. 3. Slide the large washers with the plastic bushings to the inside. 4. Remove the cushion, and lower it to the platform. 5.
Lubrication Grease with No. 2 general purpose lithium base or molybdenum base grease. Lubricating the Machine Service Interval: Every 50 hours—Grease the lift linkage (more often in dirty or dusty conditions). Every 50 hours—Grease the mower-deck spindles (more often in dirty or dusty conditions). g015589 Use the following graphics for locating the grease points. Figure 39 Greasing the Front Caster Pivots Service Interval: Yearly Lubricate the front caster pivots once a year. 1.
Lubricating the Caster-Wheel Hubs 13. Torque the nut to 8 to 9 N-m (71 to 80 in-lb), loosen, then torque it to 2 to 3 N-m (20 to 25 in-lb). Note: Make sure axle does not extend beyond either nut. Service Interval: Yearly 1. Stop the engine, wait for all moving parts to stop, engage the parking brake, and remove the key. 14. Install the seal guards over the wheel hub and insert wheel into caster fork. 15. Install caster bolt and tighten nut fully.
Engine Maintenance Cleaning the Foam Air-Cleaner Element Service Interval: Every 25 hours Servicing the Air Cleaner 1. Wash the foam element in liquid soap and warm water. When the element is clean, rinse it thoroughly. Service Interval/Specification 2. Dry the element by squeezing it in a clean cloth. Important: Replace the foam element if it is torn or worn. Inspect the foam and paper elements, and replace them if they are damaged or excessively dirty.
g015238 1 2 3 4 6 7 8 9 Figure 42 Checking the Engine-Oil Level 5 Note: Check the oil when the engine is cold. WARNING Contact with hot surfaces may cause personal injury. Keep hands, feet, face, clothing and other body parts away the muffler and other hot surfaces. Important: Do not overfill the crankcase with oil, because damage to the engine may result. Do not run engine with oil below the Low mark, because the engine may be damaged. 1.
Changing the Engine Oil Note: Dispose of the used oil at a recycling center. 1 2 3 4 5 6 1. Park the machine so that the drain side is slightly lower than the opposite side to assure the oil drains completely. 2. Disengage the PTO, move the motion-control levers to the neutral-locked position, and set the parking brake. 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 4. Change the engine oil as shown in Figure 44.
Removing the Spark Plug 1. Disengage the PTO, move the motion-control levers to the neutral-locked position, and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Remove the spark plug as shown in Figure 47. 1 2 3 4 5 6 Figure 47 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has a black coating, worn electrodes, an oily film, or cracks.
Installing the Spark Plug Fuel System Maintenance Tighten the spark plug(s) to 22 N-m (16 ft-lb). Draining the Fuel Tank Note: There is no other recommended way to drain fuel from the tank, other than using a syphon pump. A syphon pump can be purchased at a hardware store. DANGER Figure 49 In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property.
Servicing the Fuel Filter Replacing the Fuel Filter Electrical System Maintenance Service Interval: Every 800 hours/Yearly (whichever comes first) Servicing the Battery Do not install a dirty filter if it is removed from the fuel line. Service Interval: Every 100 hours Note: Wipe up any spilled fuel. Always keep the battery clean and fully charged. Use a paper towel to clean the battery case.
2. Secure the battery with the hold down plate, j-bolts, and locknuts. WARNING Incorrect battery-cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 3. Install the positive (red) battery cable to positive (+) battery terminal with a nut, a washer, and a bolt (Figure 52). 4. Slide the rubber cover over the post. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses, and requires no maintenance. If a fuse blows, check the component or circuit for a malfunction or short. 1. Release the cushion from the rear of the machine. Adjusting the Tracking 2. Pull out on the fuse to remove or replace it (Figure 54). Note: Determine the left and right sides of the machine from the normal operating position. 3. Install the cushion to the rear of the machine. 1.
3 6. Test the safety-interlock system before operation. 1 6 2 3 4 g017848 Figure 56 1. Left cable adjustment 3. Right cable adjustment 6 2. Cable lock 7. Check for proper tracking. 2 Note: If the machine will not start after adjusting the tracking, make sure proximity switch target aligns with bolt attached to motion-control lever; refer to Adjusting the Proximity Switch (page 42). 4 5 8. Repeat the cable adjustment until the tracking is correct. G015609 Figure 57 1.
Checking the Tire Pressure Service Interval: Every 50 hours/Monthly (whichever comes first) Maintain the air pressure in the rear tires at 83 to 97 kPa (12 to 14 psi). Important: Uneven tire pressure can cause an uneven cut. Note: The front tires are semi-pneumatic tires and do not require air-pressure maintenance. Figure 59 1. Spring washers 3. Dust cap 2. Locknut Servicing the Caster Wheels and Bearings Figure 58 The caster wheels rotate on a roller bearing supported by a spanner bushing.
2. Remove one bushing, then pull the spanner bushing and roller bearing out of the wheel hub (Figure 60). 3. Remove the other bushing from the wheel hub, and clean any grease and dirt from the wheel hub (Figure 60). 4. Inspect the roller bearing, bushings, spanner bushing and the inside of the wheel hub for wear. Note: Replace any defective or worn parts (Figure 60). Figure 61 5. Place one bushing into the wheel hub (Figure 60). 1. Adjusting nut 6.
Cooling System Maintenance Brake Maintenance Cleaning the Air-Intake Screen Before each use, check the brakes on a level surface and slope. Service Interval: Before each use or daily Always set the parking brake when you stop the machine or leave it unattended. Servicing the Brake Before each use, remove any buildup of grass, dirt, or other debris from the cylinder and cylinder head cooling fins, air intake screen on the flywheel end, and the carburetor-governor levers and linkage.
Adjusting the Brakes 1 If the parking brake does not hold securely, an adjustment is required. 2 1. Check the brake before you adjust it; refer to Checking the Parking Brake (page 45). 2. Park the machine on a level surface, disengage the PTO, and set the parking brake. 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 4 3 4. Release the parking brake. 5.
Belt Maintenance 1 2 Replacing the Mower-Deck Belt 3 Service Interval: Every 100 hours—Check the mower-deck belt. Squeaking when the belt is rotating, the blade is slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn deck belt. Replace the deck belt if any of these conditions are evident. 1. Disengage the PTO and set the parking brake. 5 2 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
G015595 6 g017890 Figure 66 1. 16.5 cm (6.5 inches) from hook to hook 2. Spring 4. Ratchet 3. Spring-loaded idler 6. Nut 5 Figure 67 5. Square hole for ratchet 1. 16.5 cm (6.5 inches) from hook to hook 2. Spring 4. Ratchet 3. Spring-loaded idler 6. Nut 5. Square hole for ratchet Replacing the Pump-Drive Belt Service Interval: Every 100 hours—Check the pump-drive belt. 1. Disengage the PTO and set the parking brake. 2.
Controls System Maintenance 6 Adjusting the Motion-Control-Handle Positions Adjusting the Right Side Motion-Control Lever If the motion-control levers do not align horizontally, adjust the right side motion-control lever. 1 Note: Adjust the horizontal alignment before the front to back alignment. 1. Disengage the PTO, move the right side motion-control lever to the neutral position, and set the parking brake. 2.
Adjusting the Neutral Position for the Motion-Control Levers Important: Ensure the tracking of the mower is correct after adjusting the motion-control levers. Adjusting the tracking and aligning the motion-control levers front to back is the same procedure (Figure 71). Note: Adjust the horizontal alignment before the front to back alignment. If the motion-control levers do not align front to back, or the right side control lever does not move easily into the neutral-lock position, adjustment is required. 1.
Hydraulic System Maintenance 3 Servicing the Hydraulic System Hydraulic Oil Type: Toro® HYPR-OIL™ 500 hydraulic oil or Mobil® 1 15W-50 synthetic motor oil. Hydraulic System Oil Capacity: 2.0 L (67 oz) Important: Use oil specified. Other fluids could cause system damage. Checking the Hydraulic Fluid Service Interval: After the first 8 hours Every 50 hours Note: There are 2 ways to check the hydraulic oil; when the oil is warm, or when the oil is cold.
4. Locate the front hydraulic hose under the hydraulic tank, and place a drain pan under the tank (Figure 74). 8. Check the fluid level while the fluid is warm. Note: If required, add fluid to the reservoir until it is between the hot level and the cold level. 5. Loosen the hose clamp and move it down the hose. 6. Remove the front hydraulic hose, and allow the fluid to run out of the tank. Note: The fluid level should be below the hot level of the baffle when the fluid is warm (Figure 73). 1 9.
Replacing the Hydraulic Filter Service Interval: After the first 8 hours WARNING Hot hydraulic fluid can cause severe burns. Allow the hydraulic fluid to cool before performing any maintenance to the hydraulic system. Important: Do not substitute with an automotive oil filter, or severe hydraulic system damage may result. Figure 76 1. Disengage the PTO and set the parking brake. 1. Hydraulic filter 2. Stop the engine and wait for all moving parts to stop before leaving the operating position. 3.
Mower Deck Maintenance Checking the Hydraulic Lines Service Interval: Every 100 hours Check hydraulic hoses and hoses for leaks, loose fittings, kinked hoses, loose mounting supports, wear, general weathering, and chemical deterioration. Make any necessary repairs before operating. Servicing the Cutting Blades To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, you may want to keep extra blades on hand.
Removing the Blades Checking for Bent Blades 1. Disengage the PTO, move the motion-control levers to the neutral-locked position, and set the parking brake. Blades must be replaced if a solid object is hit, if the blade is out of balance, or if the blade is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in nonconformance with safety standards. 2.
Correcting the Mower Quality-of-Cut Note: If the blade stays in a horizontal position, the blade is balanced and can be used. If one deck blade cuts lower than the other, correct it as follows: Note: Tire air pressure is critical in these procedures; make sure the rear tires have the correct pressure. Figure 81 1. Blade 1. Disengage the PTO and set the parking brake. 2. Balancer 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
Changing the Mower Deck Side-to-Side Height Changing the side-to-side height is done by adjusting the rear-tire pressure and U-plates on the side of the engine deck. 1. Change the rear-tire pressure. Note: Do this to the corresponding side that needs adjustment. 2. Locate the U-plates on the side of the engine deck (Figure 84). 3. Loosen the U-plate on 1 side, and adjust it up or down to make the difference between measurements B and C no more than a 6 mm (1/4 inch) as shown in Figure 84. Figure 85 4.
4. Tighten both the front and rear nuts. 5. Check the front-to-rear pitch of the cutting unit. 6. If the dimensions are not correct, adjust the front and rear nuts on either side to get the correct front-to-rear pitch (Figure 87). Figure 88 1. Measure from a level surface 2. Measure the blade at point A 5. If it does not measure correctly, locate the height-of-cut rod on the right side of the machine (Figure 89). 6. Adjust the adjustment bolt until the blade tips match 7.
Replacing the Grass Deflector Cleaning WARNING Cleaning under the Mower An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or bystander's direction and result in serious injury. Also, contact with the blade could occur. Service Interval: Before each use or daily Remove the grass buildup under the mower daily. 1. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake.
Storage 13. Store the machine in a clean, dry garage or storage area. Remove the key from the ignition switch and keep it in a memorable place. Cover the machine to protect it and keep it clean. Cleaning and Storage 1. Disengage the power take off (PTO), set the parking brake, turn the ignition key to off, and remove the key. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Important: You can wash the machine with a mild detergent and water.
Troubleshooting Problem The engine will not start, starts hard, or fails to keep running. The engine loses power. The engine overheats. The machine does not drive. Possible Cause 1. Fuel tank is empty. 1. Fill the fuel tank with gasoline. 2. Choke is not on. 3. Spark plug wire is loose or disconnected. 4. Spark plug is pitted, fouled, or the gap is incorrect. 5. Air cleaner is dirty. 6. Dirt in the fuel filter. 7. Dirt, water, or stale fuel is in the fuel system. 8.
Problem The blades do not rotate. Possible Cause Corrective Action 1. Pump-drive belt is worn, loose or broken. 1. Check the belt tension. 2. Pump-drive belt is off the pulley. 2. Install the drive belt, and check the adjusting shafts and belt guides for correct position. 3. Install the new deck belt. 3. Mower-deck belt is worn, loose or broken. 4. Mower-deck belt is off the pulley. 5. 6. 7. 8. 9. Broken or missing idler spring. Electric clutch out of adjustment. Clutch connector or wire damaged.
Schematics Hydraulic Schematic (Rev.
G015606 Electrical Schematic (Rev.
Notes: 65
Notes: 66
International Distributor List Distributor: Country: Phone Number: Distributor: Phone Number: 57 1 236 4079 Colombia Japan 81 3 3252 2285 Czech Republic 420 255 704 220 420 255 704 Slovakia 220 Argentina 54 11 4 821 9999 Russia 7 495 411 61 20 Ecuador 593 4 239 6970 Finland 358 987 00733 Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Hungary Hong Kong Korea 36 27 539 640 852 2155 2163 82 32 551 2076 Maquiver S.A. Maruyama Mfg. Co. Inc. Mountfield a.s.
The Toro Total Warranty Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship. Landscape Contractor Equipment (LCE) Instructions for Obtaining Warranty Service If you think that your Toro Product contains a defect in materials or workmanship, follow this procedure: 1.
