Setup Instructions

ManualsBrandsToro ManualsLawn TractorsToro 74585

FormNo.3377-248RevB

DH210LawnTractor

ModelNo.74585—SerialNo.313000001andUp

ModelNo.74596—SerialNo.313000001andUp

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Steeringwheel

Rollpin1

Spacer

Cap

Installthesteeringwheel.

Seat

Bolts2

Adjustingknob2

Spacers

Springwashers

Installtheseat.

Collectorcover

Coverframe

Handle1

Springwasher

Handlescrew2

Screw

Steelwasher

Rubberwasher12

Nut6

Outerframe

Hingepin2

Snapring

Grasscollectordumplever

Grasscollectordumpleverscrew

Assemblethegrasscollector.

Nopartsrequired

–

Checktheoillevel.

Nopartsrequired

–

Activatethebattery.

Nopartsrequired

–

FilltheFuelTank.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Lubricatethemachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheCzechRepublic

AllRightsReserved

*3377-248*B

Summary of content (8 pages)

PAGE 1
Form No. 3377-248 Rev B DH 210 Lawn Tractor Model No. 74585—Serial No. 313000001 and Up Model No. 74596—Serial No. 313000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 © 2017—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty.
PAGE 2
1 Installing the Steering Wheel Parts needed for this procedure: 1 Steering wheel 1 Roll pin 1 Spacer 1 Cap Procedure g012505 Figure 1 1. Position the front wheels straight ahead. 1. Safety switch 2. Install the plastic spacer over the steering wheel shaft (smaller diameter first). 2. Bolts and spacers 3. Slide the steering wheel over the shaft, aligning the holes on each side of the steering wheel with the holes in the spacer and with the holes in the shaft. 4.
PAGE 3
Assembling the Grass Collector Parts needed for this procedure: 1 Collector cover 1 Cover frame 1 Handle 2 Spring washer 2 Handle screw 6 Screw 6 Steel washer 12 Rubber washer 6 Nut 1 Outer frame 2 Hinge pin 2 Snap ring 1 Grass collector dump lever 1 Grass collector dump lever screw g018122 Figure 3 Cross-sectional view shown Procedure 1. 2. Align the collector frame with the collector cover. 1. Screw 3.
PAGE 4
Checking the Oil Level No Parts Required Procedure It may be necessary to add oil to the machine before first operation. Refer to the Operator’s Manual for oil type, viscosity, and crankcase capacity. Add only enough oil to raise the level to the Full mark on the dipstick. g018123 5 Figure 4 1. Snap ring 2. Hinge pin 7. Secure a hinge pin on each side of the collector (on the outside of the collector), with a snap ring installed into the groove on the pin (Figure 4). 8.
PAGE 5
Important: Use only a battery charger set to 12 volts to charge the battery. 8 Important: Do not start the engine with a battery booster (jump starter) pack. Jump-starting the engine with a battery booster pack may damage electronic components of the machine. Lubricating the Machine No Parts Required WARNING Procedure Charging the battery produces gasses that can explode. Ensure that all of the necessary points on the machine are lubricated; refer to the Operator’s Manual.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8