Setup Instructions

ManualsBrandsToro ManualsLawn TractorsToro 74585

FormNo.3373-128RevA

DH210andDH220LawnTractors

ModelNo.74585—SerialNo.312000001andUp

ModelNo.74596—SerialNo.312000001andUp

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Steeringwheel

Rollpin1

Spacer

Installthesteeringwheel.

Seat

Bolts2

Adjustingknob2

Flatwashers4

Springwashers

Installtheseat.

Collectorcover

Coverframe

Handle1

Springwasher

Handlescrew2

Screw

Steelwasher

Rubberwasher12

Nut6

Outerframe

Hingepin2

Snapring

Grasscollectordumplever

Grasscollectordumpleverscrew

Assemblethegrasscollector.

Nopartsrequired

–

Checktheoillevel.

Nopartsrequired

–

Activatethebattery.

Nopartsrequired

–

FilltheFuelTank.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Lubricatethemachine.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheCzechRepublic

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3373-128 Rev A DH 210 and DH 220 Lawn Tractors Model No. 74585—Serial No. 312000001 and Up Model No. 74596—Serial No. 312000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 © 2012—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty.
PAGE 2
1 1 Installing the Steering Wheel Parts needed for this procedure: 1 Steering wheel 1 Roll pin 1 Spacer 3 1 Procedure 2 1. Position the front wheels straight ahead. G012505 2. Install the plastic spacer over the steering wheel shaft (smaller diameter first). Figure 1 1. Safety switch 3. Slide the steering wheel over the shaft, aligning the holes on each side of the steering wheel with the holes in the spacer and with the holes in the shaft. 2. Bolts and washers 3.
PAGE 3
Assembling the Grass Collector 1 Parts needed for this procedure: 1 Collector cover 1 Cover frame 1 Handle 2 Spring washer 2 Handle screw 6 Screw 12 Steel washer 12 Rubber washer 6 Nut 1 Outer frame 2 Hinge pin 2 Snap ring 1 Grass collector dump lever 1 Grass collector dump lever screw 2 3 4 E G018122 Figure 3 Cross-sectional view shown Procedure 1. Align the collector frame with the collector cover. 2.
PAGE 4
1 4 B A Checking the Oil Level 2 No Parts Required A Procedure The machine comes from the factory with oil in the engine crankcase; however, it may be necessary to add oil. Refer to the Operator’s Manual for oil type, viscosity, and crankcase capacity. Add only enough oil to raise the level to the Full mark on the dipstick. G018123 Figure 4 5 2. Hinge pin 1. Snap ring 7.
PAGE 5
WARNING 9 Charging the battery produces gasses that can explode. Checking the Safety System Never smoke near the battery, and keep sparks and flames away from the battery. No Parts Required 6. Install the filler caps after the battery is fully charged. 7. Install the battery in the chassis; refer to the Operator’s Manual. Procedure Refer to the Operator’s Manual. 6 Filling the Fuel Tank No Parts Required Procedure Add fuel to the fuel tank; refer to the Operator’s Manual.
PAGE 6
Notes: 6
PAGE 7
Notes: 7
PAGE 8