Setup Instructions

ManualsBrandsToro ManualsLawn TractorsToro 74592

FormNo.3360-473RevB

DH200,DH210,andDH220LawnTractors

SerialNo.280000001andUp

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

SteeringWheel

LockWasher1

Nut1

Installingthesteeringwheel

Seat

Bolts2

FlatWashers2

SpringWashers

Installingtheseat

TrailerHitch1

Bolts2

Nuts2

Attachingthetrailerhitch

CollectorCover

GrassCollector—PartiallyAssembled

GrassBag

FastenerPackage1

ArrowDecal1

Assemblingthegrasscollector

Nopartsrequired

–

Checkingtheoillevel

Nopartsrequired

–

Activatingthebattery

Nopartsrequired

–

Fillingthefueltank

Nopartsrequired

–

Checkingthetirepressure

Nopartsrequired

–

Lubricatingthemachine

Keys2

UsingintheignitionandKeyChoice™

switch

Nopartsrequired

–

Checkthesafetysystem

Operator’sManual

EngineOperator’sManual

Readingbeforeoperatingthemachine

CerticateofConformance

CEconformance

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3360-473 Rev B DH 200, DH 210, and DH 220 Lawn Tractors Serial No. 280000001 and Up Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 12 13 © 2009—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Use Qty.
PAGE 2
1 2 Installing the Steering Wheel Installing the Seat Parts needed for this procedure: Parts needed for this procedure: 1 Steering Wheel 1 Seat 1 Lock Washer 2 Bolts 1 Nut 2 Flat Washers 2 Spring Washers Procedure 1. Position the front wheels straight ahead. Procedure 2. Remove the logo cover by releasing the 3 latches from the back side with a screwdriver. 1. Remove the plastic cover from the seat and discard it. 3.
PAGE 3
4 Attaching the Trailer Hitch Assembling the Grass Collector Parts needed for this procedure: 1 Trailer Hitch 2 Bolts 2 Nuts Parts needed for this procedure: Procedure 1. Line up the holes in the trailer hitch with the holes in the machine frame. 2. Attach the hitch with two bolts and nuts (Figure 3). 1 Collector Cover 1 Grass Collector—Partially Assembled 1 Grass Bag 1 Fastener Package 1 Arrow Decal Procedure 1. Tilt the front tube of the partially assembled collector. 2.
PAGE 4
12. Place the cover on the grass collector. 13. Align the cover with the rear fender by adjusting the rear machine supports until there is a proper seal between the cover and the collector. 14. Tighten the rear machine support bolts. 15. Remove the grass collector from the machine. 16. Tighten all screws securely. 17. Use the plastic extrusions on the bag edges to fix the bag to the frame tube. 18.
PAGE 5
8 Battery electrolyte contains sulfuric acid that is poisonous (if consumed) and can severely burn you. Checking the Tire Pressure • Do not drink electrolyte. No Parts Required • Avoid contact with skin, eyes or clothing. Procedure • Wear safety glasses to shield your eyes and rubber gloves to protect your hands. Check front and rear tires for proper inflation; refer to the Operator’s Manual for the recommended inflation pressure.
PAGE 6
12 Test Driving the Machine Parts needed for this procedure: 1 Operator’s Manual 1 Engine Operator’s Manual Procedure Ensure that all electrical and mechanical systems are operating properly. Refer to the Operator’s Manual for how to properly operate the controls.
PAGE 7
Notes: 7
PAGE 8