Form No. 3383-842 Rev A DH 220 Lawn Tractor Model No. 74596—Serial No. 314000001 and Up G017868 Register at www.Toro.com.
This product complies with all relevant European directives. For details, see the separate product specific Declaration of Conformity (DOC) sheet. Figure 2 1. Safety alert symbol Introduction This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. This rotary-blade, riding lawn mower is intended to be used by residential homeowners.
Contents Mower Deck Maintenance...........................................29 Servicing the Blades................................................29 Removing the Mower..............................................30 Installing the Mower ...............................................30 Storage ........................................................................31 Troubleshooting ...........................................................32 Schematics .....................................................
Safety Safe Operation Practices for Riding Rotary Lawn Mowers Read and understand the contents of this manual before operating the machine. The safety alert symbol (Figure 2) is used to alert you to potential personal injury hazards. Obey all safety messages that follow this symbol to avoid possible injury or death. The following instructions are from the CEN standard EN 836:1997. • • This product is capable of amputating hands and feet and of throwing objects.
• If the fuel tank has to be drained, this should be done • When using any attachments, never direct discharge of outdoors. material toward bystanders nor allow anyone near the machine while in operation. • On multi-bladed machines, take care as rotating one blade • Never operate the machine with damaged guards or can cause other blades to rotate. without safety protective devices in place.
Sound Pressure This unit has a sound pressure level at the operator’s ear of 82 dBA, which includes an Uncertainty Value (K) of 1 dBA. The sound pressure level was determined according to the procedures outlined in EN 836. Sound Power This unit has a guaranteed sound power level of 100 dBA, which includes an Uncertainty Value (K) of 1 dBA. The sound power level was determined according to the procedures outlined in ISO 11094. Vibration Hand-Arm • Measured vibration level for right hand = 2.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. 104-3238 93-7276 1. Explosion hazard—wear eye protection. 3. Fire hazard—no fire, open flames, or smoking. 2. Caustic liquid/chemical burn hazard—to perform first aid, flush with water. 4.
111-5630 1. Moving in reverse enabled 3. Empty the grass collector 2. Lights 4. Power Take-off (PTO) 119-2725 1. Warning—read the Operator's Manual. 111–5941 2. Warning—remove the spark plug wire before performing any maintenance on the machine. 1. Warning—keep hands away from moving parts. 3. Tipping hazard—do not operate on slopes greater than 10 degrees. 4. Thrown object hazard; crushing hazard, bystanders—keep bystanders a safe distance from the machine. 5.
Product Overview Operation Controls Note: Determine the left and right sides of the machine from the normal operating position. Become familiar with the controls (Figure 4) before you start the engine and operate the machine. Filling the Fuel Tank Recommended Fuel: • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method).
of the filler neck. Do not fill the fuel tank completely full. Do not fill the fuel tank completely full. Note: This space in the tank allows gasoline to expand. 4. Install the fuel tank cap securely. 5. Wipe up any gasoline that may have spilled. Checking the Engine Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine Oil Level in Servicing the Engine Oil in the Maintenance section.
Important: You must set the height-of-cut lever to the highest position (7) when you transport the machine off the lawn to prevent damaging the blades. Note: The engine will not start if the blades (PTO) are engaged. 5. When starting a cold engine, pull out the choke knob (Figure 9). 1. Push and hold in the button on the height-of-cut lever (Figure 7). 1 1 G017870 Figure 7 1. Height-of-cut lever G017871 2 Figure 9 2. Shift the height-of-cut lever to the desired position. 1.
Note: If the engine backfires, shift the throttle control lever to the Fast position before stopping the engine. 2. Turn the ignition key to the Off position (Figure 10). If you need to use the blades (PTO) while backing up, turn off the interlock feature using the KeyChoice switch located near the seat bracket (Figure 11). Note: If the engine has been working hard or is hot, let it idle for a minute before turning the ignition key to the Off position.
1 6. Shift the blade control (PTO) knob to the Disengage position: The operating-in-reverse warning light should turn off. Pushing the Machine Manually G017873 Figure 12 Important: Always push the machine manually. Never tow the machine because it may damage the transaxle. 1. Operating-in-reverse light 4. Operate the machine in reverse and complete your task. 5. Disengage the blades (PTO) to activate the interlock. 6. Remove the KeyChoice key and put it in a safe place out of the reach of children.
Driving the Machine Forward or Backward 2. Disengage the blades (PTO). 3. Turn the ignition key to the Off position. 4. Set the parking brake if you leave the machine unattended; refer to Setting the Parking Brake. The throttle control regulates the engine speed as measured in RPM (revolutions per minute). Place the throttle control in the Fast position for best performance. Note: Remove the keys from the ignition and KeyChoice switches. To go forward: 1.
2. Disengage the blades (PTO) and move the throttle to the Slow position. 3. Pull the grass collector dump lever forward and tilt the grass collector (Figure 16). 1 G017876 Figure 17 1. Locking latch 2. Disengage the blades (PTO) and move the throttle to the Slow position. 1 3. Pull the grass collector dump lever forward and tilt the grass collector (Figure 18) until the locking latch engages to lock the grass collector in the open position (Figure 19). G017877 Figure 16 1.
Operating Tips • For the best performance, operate the engine at the 1 maximum speed. The mower requires air to thoroughly cut grass clippings, so do not set the height-of-cut too low or completely surround the mower in uncut grass. Always leave one side of the mower free from uncut grass to allow the air to be drawn into the mower. • Cut the grass slightly longer than normal to ensure that the cutting height of the mower does not scalp any uneven ground.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily • • • • • • Check the safety interlock system. Check the engine oil level. Check the battery electrolyte level. Check the brake. Check the blades. Clean the mower housing. Every 25 hours • Grease and lubricate the machine.
Where to Add Grease 7. Wipe up any excess grease.
Cleaning the Air Filter 2. Unscrew the knobs and remove the air filter cover (Figure 22). 1. Inspect the air filter for tears, and oily film, or damage to the rubber seal. 2. To loosen the debris, gently tap the filter on a hard surface. If the filter is excessively dirty, replace it with a new filter. Important: Never clean the paper element with pressurized air or liquids such as solvents, gasoline, or kerosene. Replace the air filter if it is damaged or cannot be cleaned thoroughly.
Figure 26 Figure 25 1. Drain plug 1. Dipstick/fill hole 3. Filler tube 2. Metal end 10. When oil has drained completely, insert the drain plug and tighten it securely. 8. Unscrew the dipstick and wipe the metal end clean (Figure 25). Note: Note: Recycle the used engine oil properly. 11. Clean around the dipstick and unscrew the cap (Figure 25). 9. Screw the dipstick fully onto the filler tube (Figure 25). 10. Unscrew the dipstick again and look at the metal end.
Servicing the Spark Plug 6. Fill the crankcase with the proper type of new engine oil; refer to Checking the Engine Oil Level. Service Interval: Every 25 hours—Check the spark plug. Every 100 hours—Replace the spark plug. Use a Champion RC12YC or equivalent spark plug. Ensure that the air gap between the center and side electrodes is 0.030 inch (0.76 mm) before installing the spark plug.
Fuel System Maintenance Draining the Fuel Tank Drain the fuel tank when you will not be using the machine for more than 30 days. Figure 29 1. Center electrode insulator 3. Air gap (not to scale) DANGER 2. Side electrode In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. Important: Do not clean the spark plug.
Electrical System Maintenance Note: Now is the best time to install a new fuel filter because the fuel tank is empty. 9. Install the fuel line onto the fuel filter. 10. Slide the hose clamp close to the fuel filter to secure both the fuel line and the fuel filter (Figure 30). Replacing the Headlight Bulbs 1. Disengage the blades (PTO). Replacing the Fuel Filter 2. Set the parking brake. Service Interval: Every 100 hours/Yearly (whichever comes first) 3.
Replacing the Fuses 4. Remove the ignition key. The electrical system is protected by fuses. They are located beneath the hood, near the fuel tank (Figure 34). If a fuse goes out, check the circuit wiring for a short. 5. Lift up the seat to see the battery. 1 6. Lift the rubber cover up off the negative (black) cable. 7. Disconnect the negative (black) ground cable from the battery post (Figure 35). 2 G012460 Figure 34 1.
4. Using the bolt and wing nut, connect the negative (black) cable to the negative (–) battery post (Figure 35). Slide the rubber cover over the battery post. 4. Replace the filler caps. Charging the Battery Checking the Electrolyte Level WARNING Service Interval: Before each use or daily Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from the battery. 1. Tip the seat forward to see the battery. 2. Look at the side of the battery.
Checking the Brake Drive System Maintenance Service Interval: Before each use or daily 1. Park the machine on a level surface. 2. Disengage the blades (PTO). Checking the Tire Pressure 3. Set the parking brake. Service Interval: Every 25 hours/Yearly (whichever comes first) 4. Stop the engine and wait for all moving parts to stop. 5. Remove the ignition key. Maintain the air pressure in the front tires at 120 kPa and in the rear tires at 100 kPa. Check the pressure at the valve stem (Figure 37).
Cleaning the Grass Collector and Tunnel Servicing the Grass Collector 1. Disengage the blades (PTO). 2. Set the parking brake. Removing the Grass Collector 3. Stop the engine and wait for all moving parts to stop. 1. Lock the locking latch on the grass collector (Figure 39). 4. Remove the ignition key. 5. Remove the grass collector; refer to Removing the Grass Collector. 1 6. Clean the collector bag with pressurized water. 7. Wipe the area around the full-bag sensor. 8.
Mower Deck Maintenance Removing the Blades 1. Remove the mower; refer to Removing the Mower. 2. Carefully tip the mower over. 3. Remove the bolts, washers, and blades (Figure 41). Wedge a block of wood between each blade and the mower to lock the blade when you are removing each bolt. Servicing the Blades Service Interval: Before each use or daily Note: Determine the left and right sides of the machine from the normal operating position. Note: The right blade has a left-hand threaded bolt. 4.
Important: The relief spring is very strong. Wedge the mower housing to ensure that it does not fly upward and cause damage. 11. Remove the pin between the front arm linkage and the mower housing (Figure 45). 12. Remove the V-belt from the engine pulley (Figure 45). 13. Slide the mower out from beneath the machine. Installing the Mower Reverse the procedure for Removing the Mower. Figure 44 3. Tighten the blade bolts to 37 ft-lb (50 N-m). Removing the Mower 1. Park the machine on a level surface. 2.
Storage 13. Remove and inspect the spark plug; refer to Servicing the Spark Plug. With the spark plug removed from the engine, pour 2 tablespoons of engine oil into the spark plug hole. Use the electric starter to crank the engine and distribute the oil inside the cylinder. Install the spark plug, but do not connect the wire to the spark plug. 1. Disengage the blades (PTO). 2. Set the parking brake. 3. Stop the engine and wait for all moving parts to stop. 4. Remove the ignition key. 14.
Troubleshooting Problem The starter does not crank. The engine overheats. The machine does not drive. The engine will not start, starts hard, or fails to keep running. Possible Cause 1. The blade control (PTO) knob is engaged. 1. Move the blade control (PTO) knob to the Disengaged position. 2. The parking brake is not on. 3. The battery is dead. 4. The electrical connections are corroded or loose. 5. A fuse is blown. 6. A relay or switch is damaged. 2. Set the parking brake. 3. Charge the battery. 4.
Problem There is abnormal vibration. The blades do not rotate. The cutting height is uneven. Possible Cause Corrective Action 1. The blades are bent or unbalanced. 1. Install a new blades. 2. The blade mounting screws are loose. 3. The engine mounting bolts are loose. 4. There is a loose engine pulley, idler pulley, or blade pulley. 5. The engine pulley is damaged. 6. The blade drive belt is damaged. 2. Tighten the blade mounting screws. 3. Tighten the engine mounting bolts. 4.
Schematics G017998 Electrical Schematic (Rev.
International Distributor List Distributor: Agrolanc Kft Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Equiver Femco S.A. ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd. Jean Heybroek b.v.
Residential Products The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair for the original purchaser1the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manua
