Form No. 3379-764 Rev A TimeCutter® SS 4235 Riding Mower Model No. 74633—Serial No. 313100001 and Up Register at www.Toro.com.
Introduction This machine is a ride-on, rotary-blade lawnmower intended to be used by homeowners in residential applications. It is primarily designed for cutting grass on well-maintained lawns. It is not designed for cutting brush, mowing grass and other growth alongside highways, or for agricultural uses. Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
Contents Schematics ...................................................................44 Introduction .................................................................. 2 Safety ........................................................................... 4 Safe Operating Practices........................................... 4 Toro Riding Mower Safety ........................................ 6 Slope Indicator ....................................................... 7 Safety and Instructional Decals .........
Safety • Never leave a running machine unattended. Always turn off blades, set parking brake, stop engine, and remove key before dismounting. This machine meets or exceeds the B71.1-2003 specifications of the American National Standards Institute, in effect at the time of production. However, improper use or maintenance by the operator or owner can result in injury.
• Be aware that loss of traction may occur going downhill. • • • • • • On slopes, the weight of the towed equipment may cause Weight transfer to the front wheels may cause drive wheels to slip and cause loss of braking and steering. Always avoid sudden starting or stopping on a slope. If tires lose traction, stop the machine, disengage the blades and proceed slowly off the slope. Use extreme care with grass catchers or other attachments.
and replace with manufacturers' recommended parts, when necessary. • Mower blades are sharp and can cut. Wrap the blade(s) or wear gloves, and use extra caution when servicing them. • Check for proper brake operation frequently. Adjust and service as required. • Maintain or replace safety and instruction decals as necessary. • Use only genuine Toro replacement parts to ensure that original standards are maintained.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7009 1. Warning—don't operate the mower with the deflector up or removed; keep the deflector in place. 106-8717 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. 1. Read the instructions before servicing or performing maintenance. 2.
119-8814 1. Parking position 4. Neutral 2. Fast 3. Slow 5. Reverse 119-8815 1. Parking position 4. Neutral 2. Fast 3. Slow 5. Reverse 119-8871 Certain models only 1. Height-of-cut Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. 121-2989 1. Bypass lever position for pushing the machine 9 2.
121-0772 1. Fast 2. Continuous variable setting 4. Choke 5. Power take-off (PTO), Blade control switch 3.
9-8874 1. Low speed 2. High speed Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual. 10.
0-2239 1. Warning—read the Operator's Manual. 5. Warning—do not use split ramps, use a full ramps when transporting machine. 2. Warning—read the instructions before servicing or performing maintenance; move the motion control levers to the park (brake) position, remove the ignition key and disconnect the spark plug wire. 6. Loss of traction/control hazard, slopes—loss of traction/control on a slope, disengage the blade control switch (PTO), proceed off the slope slowly. 3.
Product Overview 4 3 5 9 8 6 2 7 1 10 2 g023853 11 Figure 4 1. Deflector 4. Height of cut lever 7. Footrest 10. Engine 2. Rear drive wheel 5. Operator seat 8. Fuel tank cap 11. Front caster wheel 3. Motion control levers 6. Smart Speed™ lever 9. Control panel Controls Ignition Switch Become familiar with all of the controls in Figure 4 and Figure 5 before you start the engine and operate the machine. The ignition switch has three positions, Off, Run and Start.
reverse; wheel speed is proportional to the amount the lever is moved. Move the control levers outward from the center to the park position and exit the machine (Figure 16). Always position the motion control levers into the park position when you stop the machine or leave it unattended.
DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling. • Do not fill gasoline containers inside a vehicle or on a truck or trailer bed because interior carpets or plastic truck bed liners may insulate the container and slow the loss of any static charge.
2. Slowly add regular, unleaded gasoline until the fuel reaches the base of the filler neck (Figure 9). The safety interlock system also is designed to stop the engine whenever the control levers are out of the park position and you rise from the seat. 1 2 Before Starting 3 Recommended Fuel 4 • For best results, use only clean, fresh, unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). • Oxygenated fuel with up to 10% ethanol or 15% MTBE by volume is acceptable.
Starting the Engine 1. Sit down on the seat and move the motion controls outward to the park position. 2. Disengage the blades by moving the blade control switch to Off (Figure 11) Figure 12 Figure 11 1. Control panel 2. Blade control switch—Off position 1. Control panel 4. Continuous variable setting 2. Throttle 3. Fast 5. Slow 6. Choke control 4. Turn the ignition key to Start to energize the starter. When the engine starts, release the key (Figure 13). 3.
Figure 14 1. Control panel Figure 13 1. Control panel 5. Run 2. Ignition key—run position 6. Start 3. Ignition key—start position 7. Choke control 2. Blade control switch—On position Disengaging the Blades 4. Off Push down on the blade control switch to move it to the Off position and disengage the blades (Figure 15). 5. After the engine starts, push down on the Choke control (Figure 13). If the engine stalls or hesitates, pull up on the Choke control and let the engine run for a few seconds.
1. While sitting on the seat, with the control levers in park position, and move the blade control switch to On. Try starting the engine; the engine should not crank. 2. While sitting on the seat, move the blade control switch to Off. Move either motion control lever to the center, unlocked position. Try starting the engine; the engine should not crank. Repeat with the other motion control lever. 3.
WARNING Removing your hands from the motion control levers while the machine is in motion can result in a loss of control causing harm to you or bystanders. Always stop the machine and move the motion control levers to the park position before adjusting the Smart Speed™ Control System. 2. Adjust the lever to the desired position. Forward G008953 1. Move the levers to the center, unlocked position. Figure 19 2. To go forward, slowly push the motion control levers forward (Figure 16).
4 3 1 2 3 2 g019929 1 5 Figure 21 1. Anti-scalp roller 4. Upper hole—the mower deck in the 63mm (2-1/2 inch) and below height-of-cut positions 2. Lower hole—the mower deck in the 76mm (3 inch) and above height-of-cut positions 5. Bolt G014476 Figure 20 1. Height-of-cut lever 3. Flange Nut 3. 4.5 inch (115 mm), Transport position 2. Height-of-cut positions Positioning the Seat 1. Pull up and inward on the lever to move it to the desired cutting position.
Adjusting the Motion Control Levers 3. Locate the bypass levers on the frame on both sides of the engine. 4. Move the bypass levers forward through the key hole and down to lock them in place as shown inFigure 24. Ensure this is done for each lever. Adjusting the Height The motion control levers can be adjusted higher or lower for maximum operator comfort. 5. Move the motion control levers inward to the neutral position and turn the ignition key to the run position. Do not start the machine. 1.
Mowing Direction DANGER Alternate mowing direction to keep the grass standing straight. This also helps disperse clippings which enhances decomposition and fertilization. Without the grass deflector, discharge cover, or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris. Contact with rotating mower blade(s) and thrown debris will cause injury or death.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • • • • • • • Check the safety interlock system. Check the air cleaner for dirty, loose or damaged parts. Check the engine oil level. Check air intake and cooling areas, clean as necessary. Check the cutting blades. Inspect the grass deflector for damage. Clean the mower housing.
Premaintenance Procedures Lubrication Raising the Seat Service Interval: Every 25 hours—Grease all lubrication points. Make sure the motion control levers are locked in the park position. Lift the seat forward. Grease Type: No. 2 General Purpose Lithium Base Grease Greasing the Bearings 1. Park the machine on a level surface and disengage the blade control switch. The following components can be accessed by raising the seat: • Serial plate 2.
Engine Maintenance Servicing the Engine Oil Oil Type: Detergent oil (API service SJ or higher) Servicing the Air Cleaner Crankcase Capacity: 2.0 qt (1.9 l) when the filter is changed Viscosity: See the table below. Service Interval: Before each use or daily—Check the air cleaner for dirty, loose or damaged parts. Every 50 hours—Service the paper element. (more often under extremely dusty, dirty conditions) Every 100 hours—Replace the paper element.
5. Pull the dipstick out and check the oil level. (Figure 29). The oil level should be up to, but not over, the Full or F mark on the dipstick 6. If the level is low, add oil of the proper type, up to the Full or F mark on the dipstick. Always check the level with the dipstick before adding more oil. Note: To prevent extensive engine wear or damage, always maintain the proper oil level in the crankcase.
the pad, then tighten the filter an additional 3/4 to 1 turn (Figure 31). Wipe up any excess oil on the frame. 12. When oil has drained completely, install the oil drain plug. Tighten the plug to 125 in-lb (14 N-m) torque. Wipe up any excess oil (Figure 30). 1 Note: Dispose of the used oil at a recycling center. 13. Slowly pour approximately 80% of the specified oil into the filler tube (Figure 29). 14. Install the oil fill cap/dipstick (Figure 29). 15.
Cleaning the Blower Housing Fuel System Maintenance Service Interval: Before each use or daily—Check air intake and cooling areas, clean as necessary. Every 100 hours—Clean the blower housing (more often under extremely dusty, dirty conditions). DANGER In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property.
Electrical System Maintenance 4. Squeeze the ends of the hose clamps together and slide them away from the filter (Figure 34). 5. Remove the filter from the fuel lines. 6. Install a new filter with the flow direction arrow coming from the fuel tank and pointing to the engine. Move the hose clamps close to the filter (Figure 34) to secure it in place.
Note: Do not run the machine with the battery disconnected, electrical damage may occur. 5. Slide the rubber cover up the positive (red) cable. Disconnect the positive (red) cable from the battery post (Figure 35). Retain all fasteners. 6. Remove the battery hold-down (Figure 35) and lift the battery from the battery tray. 3 2 6 5 Installing the Battery 1. Position the battery in the tray (Figure 35). 2.
Drive System Maintenance 2. Rotate the shaft forward to release the brake. Checking the Tire Pressure Service Interval: Every 25 hours—Check tire pressure. Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause uneven cut. Check the pressure at the valve stem (Figure 38). Check the tires when they are cold to get the most accurate pressure reading. Refer to the maximum pressure suggested by the tire manufacturer on the sidewall of the caster wheel tires.
Mower Maintenance Servicing the Cutting Blades Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. Figure 40 Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary.
3. Measure from the tip of the blade to the flat surface here. 1 1 G014973 3 2 G014973 3 Figure 44 2 1. Opposing blade edge, in position for measuring Figure 42 2. Level surface 3. Second measured distance between blade and surface (B) 1. Blade, in position for measuring 2. Level surface 3. Measured distance between blade and surface (A) WARNING A blade that is bent or damaged could break apart and could seriously injure or kill you or bystanders. 4.
Leveling the Mower Deck Check to ensure the mower deck is level any time you install the mower or when you see an uneven cut on your lawn. The mower deck must be checked for bent blades prior to leveling; any bent blades must be removed and replaced. Refer to the Checking for Bent Blades procedure before continuing. The mower deck must be leveled side-to-side first then the front to rear slope can be adjusted. Figure 45 Requirements: 4. Blade bolt 5. Blade stiffener 1. Sail area of blade 2. Blade 3.
Note: Avoid placing the supports under any anti-scalp rollers if present on the deck. 7. Move to the left side of the machine. Check if the side carriage bolt is in the fixed or slotted position (Figure 49). 1 3 G015323 4 5 2 1 G015324 Figure 51 4 3 2 1. Hanger bracket 4. Side locking nut 5. Side carriage bolt 3. Side locking nut 4. Adjustment notches 10. Use the notches on the welded bracket to measure the amount of adjustment. Each notch surface is equivalent to 0.
1. Park the machine on a level surface and disengage the blade control switch. 7. To raise the front of the mower, tighten the adjustment nut. To lower the front of the mower, loosen the adjustment nut. 2. Move the motion control levers outward to the park position, stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 8. After adjustment, check the front-to-rear slope again. Continue adjusting the nut until the front blade tip is 1/16-5/16 inch (1.
WARNING The spring is under tension when installed and can cause personal injury. Be careful when removing the belt. 2 2 2 3 5 1 3 1 4 G005077 Figure 56 1. Mower deck 2. Hanger bracket 3 3. Rear lift rod 6. Slide the mower deck rearward to remove the mower belt from the engine pulley. 4 7. Slide the mower deck out from underneath the machine. G014930 6 Note: Retain all parts for future installation. Figure 57 Mower Belt Maintenance 1. Idler pulley 4. Spring 2. Mower belt 5.
Replacing the Grass Deflector Important: The grass deflector must be spring loaded in the down position. Lift the deflector up to test that it snaps to the full down position. Service Interval: Before each use or daily—Inspect the grass deflector for damage. WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or bystander's direction and result in serious injury. Also, contact with the blade could occur.
Cleaning 8. Run the mower again for one to three minutes to remove excess water. Washing the Underside of the Mower WARNING A broken or missing washout fitting could expose you and others to thrown objects or blade contact. Contact with blade or thrown debris can cause injury or death. Service Interval: Before each use or daily—Clean the mower housing. Wash the underside of the mower after each use to prevent grass buildup for improved mulch action and clipping dispersal. 1.
Storage section. With the spark plug(s) removed from the engine, pour two tablespoons of engine oil into the spark plug hole. Use the starter to crank the engine and distribute the oil inside the cylinder. Install the spark plug(s). Do not install the wire on the spark plug(s). Cleaning and Storage 1. Disengage the blade control switch, move the motion controls outward to the park position, stop the engine, and remove the key. 12. Clean any dirt and chaff from the top of the mower. 13.
Troubleshooting Problem The engine overheats. Possible Cause 1. The engine load is excessive. 1. Reduce ground speed. 2. The oil level in the crankcase is low. 3. The cooling fins and air passages under the engine blower housing are plugged. 4. The air cleaner is dirty. 2. Add oil to the crankcase. 3. Remove the obstruction from the cooling fins and air passages. 5. Dirt, water, or stale fuel is in fuel system. The starter does not crank.
Problem There is abnormal vibration. The cutting height is uneven. Possible Cause 1. The engine mounting bolts are loose. 1. Tighten the engine mounting bolts. 2. The engine pulley, idler pulley, or blade pulley is loose. 3. The engine pulley is damaged. 4. The cutting blade(s) is/are bent or unbalanced. 5. A blade mounting bolt is loose. 6. A blade spindle is bent. 2. Tighten the appropriate pulley. 1. The blade(s) is not sharp. 1. Sharpen the blade(s). 2. A cutting blade(s) is/are bent. 3.
Schematics G014644 Electrical Diagram (Rev.
Notes: 45
Notes: 46
International Distributor List Distributor: Atlantis Su ve Sulama Sisstemleri Lt Balama Prima Engineering Equip. B-Ray Corporation Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Equiver Femco S.A. G.Y.K. Company Ltd. Geomechaniki of Athens Guandong Golden Star Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irriamc Irrigation Products Int'l Pvt Ltd. Jean Heybroek b.v.
The Toro Warranty and The Toro GTS Starting Guarantee Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair for the original purchaser1the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have been performed.
