Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74670

FormNo.3393-925RevC

TimeCutter

SWRidingMower

ModelNo.SWTimeCutterModels

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Connectthebattery.

Rearhitch1

Bolt(5/16x1inch)

Locknut(5/16inch)

Installtherearhitch.

Steeringwheel

Topcover1

Locknut1

Rearcover1

Screws

Installthesteeringwheel.

Seatassembly

Seatrod

Hairpincotterpins2

Spacers(certainmodelsonly)

Installtheseatassembly.

Grassdeector(ifnotinstalled)

Installthegrassdeector.

Nopartsrequired

–

Checkthemoweradjustment.

Ignitionkey1

Hosecoupling(notincludedwithCE

models)

Operator'sManual

EngineOwner’sManual(non-Toro

engines)

KeyChoice®key(blue)

Completethesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3393-925*C

Summary of content (8 pages)

PAGE 1
Form No. 3393-925 Rev C TimeCutter® SW Riding Mower Model No. SW TimeCutter Models Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
PAGE 2
1 2 Connecting the Battery Installing the Rear Hitch No Parts Required Parts needed for this procedure: Procedure WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. 1 Rear hitch 2 Bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) Procedure 1. Install the bracket to the frame as shown in Figure 2. 2.
PAGE 3
Installing the Steering Wheel Parts needed for this procedure: 1 Steering wheel 1 Top cover 1 Locknut 1 Rear cover 2 Screws g027737 Figure 4 Procedure 1. Rotate the steering column up to the user position (Figure 3). 1. Steering-wheel cover 4. Top cover 2. Locknut 3. Steering wheel 5. Column 6. Install the rear cover to the back of the footrest with the tabs at the bottom inside the footrest and the 2 screws in the top (Figure 5).
PAGE 4
2. Connect the seat switch (Figure 7). 4 Installing the Seat Assembly Parts needed for this procedure: 1 Seat assembly 1 Seat rod 2 Hairpin cotter pins 2 Spacers (certain models only) Procedure g027695 g027695 1. Install the seat assembly to the frame with the seat rod, 2 hairpin cotter pins, and 2 spacers (certain models only) as shown in Figure 6. Figure 7 3. Route the wire harness to the right side of the machine and push the plastic connector into the seat frame hole (Figure 8).
PAGE 5
7 Installing the Grass Deflector Completing the Setup Parts needed for this procedure: Parts needed for this procedure: 1 Grass deflector (if not installed) Procedure If the grass deflector is not installed, remove it from the packaging and install it onto the mower deck. Refer to your Operator’s Manual for the correct procedure to install the grass deflector.
PAGE 6
Notes:
PAGE 7
Notes:
PAGE 8