Form No. 3433-557 Rev C Tosaerba rider TimeCutter® ZS 4200T Nº del modello 74687—Nº di serie 400000000 e superiori Registrate il vostro prodotto presso www.Toro.com.
Introduzione Questo prodotto è conforme a tutte le direttive europee pertinenti. Per informazioni dettagliate vedere la Dichiarazione di Conformità (DICO) specifica del prodotto, fornita a parte. Questo tosaerba per tappeti erbosi a lama rotante con operatore a bordo è inteso per l'utilizzo da parte di proprietari in applicazioni residenziali. È progettato principalmente per i taglio dell'erba in prati ben mantenuti.
Sicurezza in fase di manutenzione.................... 29 Programma di manutenzione raccomandato .............................................................. 30 Procedure pre-manutenzione .............................. 31 Rilascio della cortina del piatto di taglio ............. 31 Lubrificazione ...................................................... 31 Ingrassaggio dei cuscinetti ............................... 31 Manutenzione del motore .................................... 32 Sicurezza del motore .......
Requisiti generali di sicurezza Sicurezza Questa macchina è stata progettata in conformità con EN ISO 5395:2013. Questa macchina è in grado di amputare mani e piedi e di scagliare oggetti. Toro ha progettato e testato questo tosaerba per offrire un servizio ragionevolmente sicuro; tuttavia, il mancato rispetto delle istruzioni di sicurezza può comportare infortuni o la morte.
Indicatore di pendenza g011841 Figura 4 Potete copiare questa pagine per uso personale. 1. La pendenza massima che consente di utilizzare la macchina è di 15 gradi. Usate il grafico delle pendenze per determinare la pendenza di un terreno prima di utilizzare la macchina. Non utilizzate questa macchina su pendenze superiori ai 15 gradi. Ripiegate il grafico lungo la linea che indica la pendenza consigliata. 2.
Adesivi di sicurezza e informativi Gli adesivi di sicurezza e di istruzione sono chiaramente visibili e sono affissi accanto a zone particolarmente pericolose. Sostituite gli adesivi danneggiati o smarriti. decalbatterysymbols Simboli della batteria Sulla vostra batteria si trovano alcuni di questi simboli, o tutti. 1. Pericolo di esplosione. 2. 3. 4. 5. 6. Tenete lontano gli astanti dalla batteria. 7.
decal139-2391 139-2391 decal131-1097 131-1097 1. Massima 2. Minima 1. Spurgo dell’olio decal139-2394 139-2394 1. Comandi della trazione 2. Massima 3. Minima decal132-0872 132-0872 1. Pericolo di lancio di oggetti 3. Pericolo di ferite alla mano – tenete gli astanti a o al piede – tenetevi a distanza di sicurezza dalla distanza dalle parti in macchina. movimento. 4. Pericolo di 2.
decal139-2388 139-2388 1. Minima 2. Rimorchio 3. Massima decal140-2748 140-2748 decal135-3295 135-3295 Nota: Questa macchina è conforme al test di stabilità dello standard di settore nei test statici laterali e longitudinali con la massima inclinazione raccomandata indicata sull'adesivo.
Quadro generale del prodotto g293302 Figura 5 1. Motore 2. Sedile dell'operatore 3. Tappo del serbatoio del carburante 4. Leve di controllo del 7. Deflettore movimento 5. Ruota di trazione posteriore 8. Leva Smart Speed™ 6. Ruote orientabili anteriori 9. Leva dell'altezza di taglio 9 10.
Comandi Leve di controllo del movimento Prima di avviare il motore e di utilizzare la macchina, familiarizzate con tutti i comandi. Utilizzate le leve di controllo del movimento per fare marcia avanti, indietreggiare e girare la macchina nella direzione opportuna (Figura 5). Plancia Posizione di parcheggio Spostate le leve di controllo del movimento verso l'esterno, nella posizione di PARCHEGGIO quando scendete dalla macchina (Figura 23).
Funzionamento Leva dell'altezza di taglio Utilizzate la leva dell'altezza di taglio per abbassare e sollevare il piatto di taglio dalla posizione di seduta. Lo spostamento della leva verso l'alto (verso di voi) solleva il piatto da terra, mentre lo spostamento della leva verso il basso (lontano da voi) abbassa il piatto verso terra. Regolate l'altezza di taglio soltanto quando la macchina è ferma (Figura 27). Nota: Stabilite i lati sinistro e destro della macchina rispetto alla normale posizione di guida.
• Non riempite completamente il serbatoio del carburante. Riempite il serbatoio fino alla base del collo del bocchettone. Lo spazio vuoto nel serbatoio serve a contenere l'espansione della benzina. Un eccessivo riempimento del serbatoio può causare la fuoriuscita di carburante, danni al motore o al sistema di controllo delle emissioni. e sostituiteli con i ricambi raccomandati dal produttore, quando necessario. Pre-avviamento Riempite il serbatoio del carburante su una superficie pianeggiante.
• Tenete il motore e la relativa area privi di accumuli PERICOLO In talune condizioni, durante il rifornimento, vengono rilasciate scariche elettrostatiche che causano scintille in grado di fare incendiare i vapori di benzina. Incendio o esplosioni causati dalla benzina possono ustionare voi o altre persone, e causare danni. di erba, foglie, grasso od olio in eccesso e altri detriti che possano accumularsi in queste aree.
3. Spegnete il motore e togliete la chiave. 4. Pulite attorno al tappo del serbatoio del carburante. 5. Riempite il serbatoio fino alla base del collo del bocchettone (Figura 8). Uso del sistema di microinterruttori di sicurezza AVVERTENZA Nota: Non riempite completamente il Se i microinterruttori di sicurezza sono scollegati o guasti, la macchina può muoversi improvvisamente e causare lesioni personali. • Non manomettete i microinterruttori di sicurezza.
4. Sedetevi sul sedile, spostate il comando delle lame in posizione di SPEGNIMENTO e bloccate le leve di controllo del movimento in posizione di PARCHEGGIO . Avviate il motore. Con il motore acceso, spostate le leve di controllo del movimento al centro, in posizione sbloccata, inserite il comando delle lame e alzatevi leggermente dal sedile: il motore dovrebbe spegnersi. Posizionamento del sedile g027252 Il sedile può essere spostato avanti e indietro.
nella staffa saldata sul piatto di taglio (Figura 13). g293897 Figura 11 1. Fermo del dispositivo di chiusura 2. Dispositivo di chiusura g230248 Figura 13 3. Coperchio dello scarico 1. Coperchio dello scarico 3. Staffa sul piatto di taglio 2. Linguetta metallica 4. Liberate il dispositivo di chiusura a uncino sopra il coperchio dello scarico dall’asta di rotazione (Figura 15). 5.
AVVERTENZA Lo scarico del motore contiene ossido di carbonio, gas velenoso inodoro che può uccidere. Non lasciate in funzione il motore al chiuso o in un'area ristretta e confinata dove possano raccogliersi i pericolosi fumi di monossido di carbonio. • Il proprietario/operatore può impedire che si • g297786 Figura 15 1. Deflettore 2. Dispositivo di chiusura 6. • 3. Asta orientabile 4.
che i bambini rimangano dove li avete visti per l'ultima volta. – Tenete i bambini a distanza dall'area di tosatura e sotto l'attenta sorveglianza di un altro adulto responsabile che non sia l'operatore. – Prestate attenzione e spegnete la macchina se dei bambini entrano nell'area da falciare. – Prima e durante la lappatura o il cambio di direzione, guardate indietro, in basso e lateralmente per escludere la presenza di bambini piccoli. – Non permettete mai che bambini e ragazzi utilizzino la macchina.
del piatto di taglio durante l'utilizzo in pendenza può causare l'instabilità della macchina. una macchina a spinta o un decespugliatore manuale per tosare l'erba in queste zone. Avvertenze di sicurezza per il traino • L’attrezzatura da trainare deve essere agganciata soltanto al punto di attacco. • Non usate la macchina come veicolo di traino, a meno che non sia dotata di apposito attacco. • Non superate i limiti di peso per l’attrezzatura trainata e durante il traino in pendenza.
1. Tirate verso l'alto la manopola dello starter per avviarlo prima di utilizzare l'interruttore a chiave (Figura 21). Nota: Assicuratevi di innestare completamente lo starter. Può essere necessario tenere fissa la manopola in alto quando utilizzate l'interruttore a chiave. 2. Spingete giù lo starter per disinnestarlo una volta acceso il motore (Figura 21). g295538 Figura 18 Disattivazione del comando delle lame (PDF) g009174 Figura 19 g295540 Figura 21 1.
Utilizzo delle leve di controllo del movimento g004532 Figura 23 1. Leva di controllo del movimento: posizione di g295541 4. Retromarcia PARCHEGGIO Figura 22 2. Posizione centrale di sbloccaggio 5. Parte anteriore della macchina 3. Marcia avanti Spegnimento del motore 1. Disinserite le lame spostando il comando delle lame in posizione di SPEGNIMENTO (Figura 19). 2. Mettete le leve di controllo del movimento in posizione di PARCHEGGIO . 3.
AVVERTENZA La macchina può girare molto rapidamente. Potete perdere il controllo della macchina e infortunarvi o danneggiare la macchina. • Prestate molta attenzione quando sterzate. • Rallentate prima di prendere curve strette. Guida in marcia avanti Nota: Prestate sempre molta attenzione quando fate retromarcia e sterzate. 1. Sbloccate le leve portandole al centro. 2. Per fare marcia avanti spingete lentamente in avanti le leve di controllo del movimento (Figura 24).
Quanto segue è inteso puramente come consiglio per l’uso. Le regolazioni variano secondo il tipo di erba, il tenore di umidità e l’altezza dell’erba.
g019929 Figura 28 1. Rullo antistrappo 2. Foro inferiore – Utilizzare questa posizione con il piatto di taglio a un'altezza di taglio di 76 mm e superiore 4. Foro superiore – Utilizzare questa posizione con il piatto di taglio a un'altezza di taglio di 63 mm e inferiore 5. Bullone 3. Dado flangiato Suggerimenti Utilizzo dell'impostazione alta velocità g296586 Figura 27 Per ottenere migliori risultati e garantire la massima circolazione dell'aria, regolate il motore in posizione MASSIMA.
Direzione di tosatura alternata marrone, di conseguenza l'erba cresce più lentamente ed è più soggetta a malattie. Dopo ogni utilizzo controllate che le lame siano affilate e non presentino danni o segni di usura. All'occorrenza, limate eventuali tacche ed affilate le lame. Sostituite immediatamente la lama se è danneggiata o usurata, utilizzando una lama di ricambio originale Toro. Alternate la direzione della tosatura per mantenere l'erba eretta.
dell'altezza dell'autocarro o rimorchio fino al terreno. Con un'inclinazione maggiore, quando il tosaerba si sposta dalla rampa al rimorchio o all'autocarro, i componenti del tosaerba possono impigliarsi. Una maggiore inclinazione può fare ribaltare la macchina o farne perdere il controllo. Se caricate su una pendenza o nelle adiacenze, posizionate il rimorchio o l'autocarro in modo che si trovino dal lato a valle della pendenza, e la rampa si estenda in salita.
e spostate le leve di controllo del movimento verso l'esterno, in posizione di PARCHEGGIO . 2. Spegnete il motore, togliete la chiave e attendete che tutte le parti in movimento si arrestino prima di abbandonare la postazione di guida. 3. Individuate le leve di bypass sul telaio su ambo i lati del motore. 4. Spostate in avanti le leve di bypass attraverso il foro della chiavetta, quindi verso il basso per bloccarle in posizione (Figura 32). Nota: Effettuate l'operazione per ciascuna leva.
Funzionamento della macchina Spostate indietro le leve di bypass attraverso il foro della chiavetta, quindi verso il basso per bloccarle in posizione, come illustrato nella Figura 32. Nota: Effettuate l'operazione per ciascuna leva.
Manutenzione Nota: Stabilite i lati sinistro e destro della macchina dalla normale posizione di guida. AVVERTENZA Sicurezza in fase di manutenzione La rimozione o modifica di attrezzatura originale, ricambi e/o accessori può alterare la garanzia, la controllabilità e la sicurezza della macchina. Modifiche non autorizzate all'attrezzatura originale o il mancato utilizzo di ricambi originali Toro possono comportare gravi infortuni o la morte.
AVVERTENZA Il contatto con parti in movimento o superfici calde può causare infortuni. Tenete dita, mani e abiti lontano dalle parti rotanti e dalle superfici calde. • Controllate frequentemente tutti i bulloni per mantenere il serraggio corretto. Programma di manutenzione raccomandato Cadenza di manutenzione Dopo le prime 5 ore Prima di ogni utilizzo o quotidianamente Dopo ogni utilizzo Ogni 25 ore Procedura di manutenzione • Cambiate l’olio motore e il filtro.
Procedure premanutenzione Lubrificazione Rilascio della cortina del piatto di taglio Intervallo tra gli interventi tecnici: Ogni 25 ore—Ingrassate i cuscinetti della ruota orientabile. Allentate i 2 bulloni inferiori della cortina per accedere alla parte superiore del piatto di taglio (Figura 33). Tipo di grasso: grasso n. 2 a base di litio Ingrassaggio dei cuscinetti 1.
Manutenzione del motore Sicurezza del motore • Prima di controllare l'olio o di rabboccare la coppa, spegnete il motore. • Tenete mani, piedi, viso, abbigliamento e altre parti del corpo lontano dalla marmitta e altre superfici calde. g027800 Revisione del filtro dell’aria Intervallo tra gli interventi tecnici: Prima di ogni utilizzo o quotidianamente Nota: Eseguite la manutenzione del filtro dell'aria più di frequente (ogni poche ore) in ambienti molto inquinati o sabbiosi.
Manutenzione dell'elemento in schiuma sintetica del filtro dell'aria Montaggio del filtro dell'aria 1. Intervallo tra gli interventi tecnici: Ogni 25 ore/Ogni mese (optando per l’intervallo più breve)—Pulite l'elemento in schiuma del filtro dell'aria (più spesso in ambienti sporchi o polverosi). Nota: Assicuratevi di non danneggiare gli elementi. 2. Allineate i fori del filtro ai fori del collettore. 3. Ruotate il filtro nella camera e innestatelo completamente contro il collettore (Figura 37).
Cambio dell’olio motore Specifiche dell'olio motore Tipo di olio: Olio detergente (API service SF, SG, SH, SJ o SL) Capacità della coppa dell'olio: 2,4 litri con il filtro dell'olio Viscosità: Vedere la tabella seguente. g029683 Figura 38 Controllo del livello dell'olio motore Intervallo tra gli interventi tecnici: Prima di ogni utilizzo o quotidianamente g193541 Figura 39 Nota: Controllate l'olio a motore freddo.
5. Cambiate il filtro dell'olio del motore (Figura 41). Nota: Assicuratevi che la guarnizione del filtro dell'olio tocchi il motore e poi ruotate il filtro di altri ¾ di giro. g027799 g027477 Figura 41 6. g029570 Figura 40 35 Versate lentamente circa l'80% dell'olio indicato nel tubo di rifornimento e sempre con cautela rabboccate l'olio necessario per portarlo alla tacca di Pieno (Figura 42).
4. Togliete la candela (Figura 43). g027478 Figura 43 Controllo della candela Importante: Non pulite la(e) candela(e). Sostituite sempre la candela (o candele) in caso di patina nera sull'isolatore, elettrodi usurati, pellicola d'olio oppure crepe. Se l'isolatore è marrone chiaro o grigio, il motore funziona correttamente. Una patina nera sull'isolatore significa in genere che il filtro dell'aria è sporco. g193530 Figura 42 7. Regolate la distanza a 0,76 mm.
Manutenzione del sistema di alimentazione Montaggio della candela PERICOLO In talune condizioni, il carburante è estremamente infiammabile ed altamente esplosivo. Un incendio o un'esplosione causati dal carburante possono ustionare voi ed altre persone, e provocare danni. Fate riferimento a Avvertimenti sull'utilizzo del carburante (pagina 12) per un elenco completo di precauzioni relative al carburante. AVVERTENZA g027960 Figura 45 Il contatto con superfici calde può causare infortuni.
Manutenzione dell'impianto elettrico Sicurezza dell'impianto elettrico g027939 • Scollegate la batteria prima di riparare la macchina. Scollegate prima il morsetto negativo, per ultimo quello positivo. Collegate prima il morsetto positivo, per ultimo quello negativo. • Caricate la batteria in un'area aperta e ben ventilata, lontano da scintille e fiamme. Togliete la spina del caricabatterie prima di collegare o scollegare la batteria. Indossate indumenti di protezione e utilizzate attrezzi isolati.
Ricarica della batteria AVVERTENZA Una rimozione non corretta dei cavi dalla batteria può causare danni a macchina e cavi, causando scintille. che possono fare esplodere i gas delle batterie e provocare infortuni. Intervallo tra gli interventi tecnici: Prima del rimessaggio—Caricate la batteria e scollegate i cavi. 1. Togliete la batteria dal telaio; vedere Rimozione della batteria (pagina 38). • Scollegate sempre il cavo negativo (nero) della batteria prima di quello positivo (rosso). 2.
Manutenzione del sistema di trazione Revisione dei fusibili l'impianto elettrico è protetto da fusibili, che non necessitano di alcuna manutenzione; tuttavia, nel caso in cui salti un fusibile dovete controllare che non vi sia un cortocircuito e se i componenti funzionano correttamente. Controllo della pressione degli pneumatici Tipo di fusibile: Intervallo tra gli interventi tecnici: Ogni 25 ore—Controllate la pressione degli pneumatici.
Rilascio del freno elettrico 2. Potete rilasciare manualmente il freno elettrico ruotando i bracci articolati in avanti. Una volta eccitato il freno elettrico, il freno si resetta. Spegnete il motore, togliete la chiave e attendete che tutte le parti in movimento si arrestino prima di abbandonare la postazione di guida. 3. Individuate il bullone di regolazione dell’allineamento vicino alla leva di comando del movimento sul lato specifico che richiede la regolazione (Figura 52). 1.
Manutenzione della cinghia Ispezione delle cinghie 5. Allentate i 2 bulloni inferiori che fissano la cortina del piatto di taglio al piatto di taglio. Vedere Rilascio della cortina del piatto di taglio (pagina 31). 6. Servendovi di un attrezzo per la rimozione delle molle (n. cat. Toro 92-5771), sganciate la molla di rinvio dal gancio del piatto di taglio per eliminare la tensione dalla puleggia tendicinghia e togliete la cinghia dalle pulegge (Figura 54).
Manutenzione del tosaerba Sicurezza delle lame Le lame consumate o danneggiate possono spezzarsi e scagliare frammenti verso di voi o gli astanti, causando gravi ferite o anche la morte. Non cercate di riparare le lame danneggiate, in quanto potreste annullare la certificazione di sicurezza del prodotto. 1. Tagliente 3. Usura/scanalatura • Controllate le lame ad intervalli regolari, per 2. Area curva 4. Incrinatura g006530 Figura 55 accertare che non siano consumate o danneggiate.
g014973 g014973 Figura 57 Figura 59 1. Lama (in posizione per la misurazione) 1. Bordo della lama opposto (in posizione per la misurazione) 2. Superficie piana 2. Superficie piana 3. Distanza misurata tra la lama e la superficie (A) 3. Seconda distanza misurata tra la lama e la superficie (B) 4. Ruotate la stessa lama di 180 gradi in modo che il tagliente opposto si trovi ora nella stessa posizione (Figura 58). A.
Montaggio delle lame 1. Montate la lama sull'asse del mandrino (Figura 60). Importante: Perché tagli correttamente, il lato curvo della lama deve essere rivolto in alto, verso l'interno del tosaerba. g027833 3. Rondella curva 4. Bullone della lama 3. Serrate il bullone della lama a una coppia compresa tra 81 e 108 N∙m. Il livellamento del piatto di taglio deve essere controllato ogni volta che si mette in opera il tosaerba oppure quando il taglio è irregolare. Affilatura delle lame 1.
una regolazione; fate riferimento a Livellamento laterale (pagina 46). g294046 Figura 64 1. Lame in posizione longitudinale g294044 Figura 63 1. Lame in posizione laterale 3. Misurate qui dalla punta della lama alla superficie piana. 3. Misurate qui dalla punta della lama alla superficie piana. 2. Taglienti esterni 2.
g294195 Figura 67 g294196 Figura 65 1. Blocco di legno spesso 6,6 cm 6. 2. Blocco di legno spesso 7,3 cm Rimuovete la coppiglia e la rondella dal perno del braccio di sollevamento inferiore (Figura 66). g294197 Figura 66 1. Piastra dell'altezza di taglio 3. Rondella 2. Coppiglia 7. Ruotate la piastra dell’altezza di taglio a un foro differente, in modo tale che supporti il peso del piatto di taglio dopo l’installazione della piastra (Figura 67). 47 8.
Rimozione del piatto di taglio del tosaerba Livellamento longitudinale della lama 1. Ruotate il dado di regolazione nella parte anteriore del tosaerba (Figura 68). 1. Parcheggiate la macchina su una superficie pianeggiante, disinnestate il comando delle lame (PDF) e spostate le leve di controllo del movimento verso l'esterno, in posizione di PARCHEGGIO . 2. Spegnete il motore, togliete la chiave e attendete che tutte le parti in movimento si arrestino prima di abbandonare la postazione di guida. 3.
g295768 Togliete il braccio di sollevamento dal perno del piatto di taglio (Figura 70). 9. Ripetete i passaggi 7 e 8 per l’altro lato della macchina. 10. Spostate indietro il tosaerba per rimuovere la relativa cinghia dalla puleggia del motore. 11. Togliete il tosaerba da sotto la macchina. Spegnete il motore, togliete la chiave e attendete che tutte le parti in movimento si arrestino prima di abbandonare la postazione di guida. 3. Infilate il tosaerba sotto la macchina. 4.
Pulizia Lavaggio del sottoscocca del piatto di taglio Intervallo tra gli interventi tecnici: Dopo ogni utilizzo—Pulite l'alloggiamento della scocca del tosaerba. Importante: La macchina può essere lavata con detersivo neutro ed acqua. Non utilizzate lance ad alta pressione. Non utilizzate una quantità d'acqua eccessiva, in particolare in prossimità della plancia, sotto al sedile, attorno al motore, alle pompe idrauliche e ai motori.
5. Sedetevi sul sedile ed avviate il motore. 6. Innestate il comando delle lame e lasciate girare il motore per un massimo di tre minuti. 7. Disinnestate il comando delle lame, spegnete il motore, togliete la chiave e attendete che tutte le parti in movimento si siano fermate. 8. Chiudete il rubinetto e togliete il raccordo a disinnesto rapido dal raccordo di lavaggio.
11. Controllate le condizioni delle lame; vedere Revisione delle lame di taglio (pagina 43). 12. Preparate la macchina per il rimessaggio per oltre 30 giorni nel modo seguente: A. B. C. D. Immagazzinamento della batteria Aggiungete stabilizzatore/additivo del carburante al carburante fresco nel serbatoio. Osservate le istruzioni per la miscelazione riportate dal produttore dello stabilizzatore del carburante. Non utilizzare stabilizzatori a base di alcol (etanolo o metanolo).
Localizzazione guasti Problema Possibile causa Rimedio Il serbatoio del carburante ha segni di cedimento o la macchina indica spesso l'esaurimento del carburante. 1. L'elemento di carta del filtro dell'aria è ostruito. 1. Pulite l’elemento di carta. Il motore si surriscalda. 1. Il motore è sotto sforzo eccessivo. 1. Rallentate. 2. Il livello dell'olio nel carter è scarso. 3. Le alette di raffreddamento e i passaggi per l'aria sotto il convogliatore sono intasati. 4. Il filtro dell'aria è sporco.
Problema La trazione non funziona. La macchina inizia a vibrare in modo insolito. Possibile causa 1. Le valvole bypass sono aperte. 1. Chiudete le valvole di traino. 2. Le cinghie della trazione sono usurate, allentate o rotte. 3. Le cinghie della trazione sono scivolate dalle pulegge. 4. Panne della trasmissione. 2. Rivolgetevi a un Centro Assistenza autorizzato. 3. Rivolgetevi a un Centro Assistenza autorizzato. 4. Rivolgetevi a un Centro Assistenza autorizzato. 1.
Schemi g307974 Schema elettrico – 139–2356 (Rev.
Informativa sulla privacy SEE/Regno Unito Utilizzo delle vostre informazioni personali da parte di Toro The Toro Company (“Toro”) rispetta la vostra privacy. Quando acquistate i nostri prodotti, possiamo raccogliere determinate informazioni personali su di voi, direttamente da voi o tramite la vostra azienda o distributore Toro.