Form No. 3400-208 Rev B TimeCutter® SS 4225 or 5000 Riding Mower Model No. 74721—Serial No. 316000001 and Up Model No. 74732—Serial No. 316000001 and Up Register at www.Toro.com.
identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Contents Washing the Underside of the Mower................ 47 Storage ................................................................... 48 Cleaning and Storage ....................................... 48 Troubleshooting ...................................................... 49 Schematics ............................................................. 51 Safety ....................................................................... 4 Safe Operating Practices....................................
Safety • Be alert, slow down and use caution when making turns. Look behind and to the side before changing directions. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER-"personal safety instruction." Failure to comply with the instruction may result in personal injury or death. • Never leave a running machine unattended.
• Follow the attachment manufacturer's • Avoid sudden starts when mowing uphill because recommendation for weight limits for towed equipment and towing on slopes. Towed weight must not exceed the weight of the machine, operator, and ballast. Use counterweights or wheel weights as described in the attachment, or in the pulling machine Operator’s Manual. the mower may tip backwards. • Be aware that loss of traction may occur going downhill.
Service • Grass catcher components are subject to wear, damage and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace with manufacturers' recommended parts, when necessary. Safe Handling of Gasoline: To avoid personal injury or property damage, use extra care when handling gasoline and other fuels. They are flammable and the vapors are explosive. • Mower blades are sharp and can cut.
Slope Indicator g011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal93-7009 93-7009 1. Warning—do not operate the mower with the deflector up or removed; keep the deflector in place. 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts. decal105-7015 105-7015 For models with 42-inch decks decaloemmarkt Manufacturer's Mark decal99-3943 1.
decal119-8814 119-8814 1. Parking position 4. Neutral 2. Fast 3. Slow 5. Reverse decal119-8815 119-8815 1. Parking position 4. Neutral 2. Fast 3. Slow 5. Reverse decal119-8871 119-8871 For models with 42-inch decks 1. Height-of-cut decal121-2989b 121-2989 1. Bypass lever position for pushing the machine decal119-8870 119-8870 For models with 50-inch decks 1. Height-of-cut 9 2.
decal131-4036 131-4036 1. Maximum drawbar pull 36 kg (80 lb) 2. Read the Operator's Manual. decal132-0872 132-0872 1. Thrown object hazard—keep bystanders away from the machine. 3. Severing hazard of hand or foot—keep away from moving parts. 2. Thrown object hazard, raised baffle—do not operate the machine with an open deck; use a bagger or a baffle. 4. Entanglement hazard—keep away from moving parts; keep all guards and shields in place.
decal131-3947 131-3947 1. Trim—slow 2. Tow—medium 3. Mow—fast decal131-4161 131-4161 For models with 42-inch decks 1. Fast 2. Slow 3.
decal131-4162a 131-4162 For models with 50-inch decks 1. Fast 2. Continuous-variable setting 3. Slow 4.
decal132-0869 132-0869 1. Warning—read the Operator's Manual. 5. Ramp tipping 3. Cutting hazard of hand, hazard—when loading mower blade; pinching onto a trailer, do not use hazard of hand, belt—keep dual ramps; only use a hands and feet away from single ramp wide enough moving parts; keep all for the machine and that guards and shields in place. has an incline less than 15 degrees; back up the ramp (in reverse) and drive forward off the ramp. 2.
Product Overview g027933 Figure 4 1. Deflector 4. Height-of-cut lever 7. Footrest 10. Control panel 2. Rear drive wheel 5. Operator seat 8. Engine 11. Engine guard 3. Motion-control levers 6. Smart Speed™ lever 9. Fuel-tank cap 12. Front caster wheel Controls Ignition Switch Become familiar with all of the controls in Figure 4 and Figure 5 before you start the engine and operate the machine. The ignition switch has 3 positions: OFF, RUN, and START .
Operation levers outward from the center to the PARK position when exiting the machine (Figure 13). Always position the motion-control levers into the PARK position when you stop the machine or leave it unattended. Note: Determine the left and right sides of the machine from the normal operating position.
Add the correct amount of gasoline stabilizer/conditioner to the gasoline. DANGER In certain conditions during fueling, static electricity can be released, causing a spark that can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance. CAUTION This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss through extended periods of exposure. Think Safety First Wear hearing protection when operating this machine. Please read all safety instructions and symbols in the safety section. Knowing this information could help you or bystanders avoid injury.
1. Starting the Engine While sitting on the seat, with the control levers in the PARK position, and move the blade-control switch to the ON position. Try starting the engine; the engine should not crank. 2. While sitting on the seat, move the blade-control switch to the OFF position. Move either motion control lever to the center, unlocked position. Try starting the engine; the engine should not crank. Repeat with the other motion-control lever. 3.
Operating the Blades 3. The blade-control switch, engages and disengages power to the mower blades. This switch controls power to any attachments that draw power from the engine, including the mower deck and cutting blades. Turn the ignition key to Off and remove the key. Driving the Machine Driving the machine benefits from an understanding of what zero-turn-radius mower means.
Driving Forward Note: Always use caution when backing up and turning. 1. Move the levers to the center, unlocked position. 2. To go forward, slowly push the motion-control levers forward (Figure 14). g004532 Figure 13 g008952 1. PARK position 4. Backward 2. Center, unlock position 5. Front of the Machine Figure 14 3. Forward To go straight, apply equal pressure to both motion-control levers (Figure 14).
Driving Backward Note: Always use caution when backing up and turning. 1. Move the levers to the center, unlocked position. 2. To go backward, look behind you and down, as you slowly pull the motion-control levers rearward (Figure 15). g027625 Figure 16 1. Smart-speed lever g008953 Figure 15 To go straight, apply equal pressure to both motion-control levers (Figure 15). To turn, release the pressure on the motion-control lever toward the direction you want to turn.
Stopping the Machine To change speeds, do the following: 1. Move the motion-control levers to neutral and outward to the PARK position. 2. Disengage the blade-control switch. 3. Adjust the lever to the desired position. To stop the machine, move the motion-control levers to neutral and outward to the PARK position, disengage the blade-control switch, ensure the throttle is between half and full throttle, and turn the ignition key to off. Remove the key from the ignition switch.
Adjusting the Anti-Scalp Rollers Positioning the Seat Move the seat forward or backward as shown in Figure 19. Whenever you change the height-of-cut, adjust the height of the anti-scalp rollers. Note: Adjust the anti-scalp rollers so that the rollers do not touch the ground in normal, flat mowing areas. 1. Disengage the blade-control switch (PTO), move the motion-control levers to the PARK position, and set the parking brake. 2.
Adjusting the Tilt You can adjust the motion-control levers fore or aft for your comfort. 1. Loosen the upper bolt holding the control lever to the control-arm shaft. 2. Loosen the lower bolt just enough to pivot the control lever fore or aft (Figure 20). 3. Tighten both bolts to secure the control lever in the new position. 4. Repeat the adjustment for the opposite control lever. g017303 Pushing the Machine by Hand Figure 21 1. Bypass-lever locations 2.
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets, or bystanders avoid injury. g027995 Figure 23 1. Back the machine up ramps.
g027996 Figure 24 1. Full-width ramp in stowed position 4. Ramp is at least four times (4X) as long as the height of the trailer or truck bed to the ground 2. Side view of full-width ramp in loading position 5. H= height of the trailer or truck bed to the ground 3. Not greater than 15 degrees 6.
Operating Tips Avoid Cutting Too Low Fast Throttle Setting If the cutting width of the mower is wider than the mower you previously used, raise the cutting height to ensure that uneven turf is not cut too short. For best mowing and maximum air circulation, operate the engine at the FAST position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower in uncut grass.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • • • • • Check the safety-interlock system. Check the air cleaner for dirty, loose or damaged parts. Check the engine-oil level. Check the cutting blades. Inspect the grass deflector for damage. After each use • Clean the mower-deck housing.
Pre-Maintenance Procedures Lubrication Raising the Seat Service Interval: Every 25 hours—Grease all the lubrication points. Make sure that the motion-control levers are locked in the PARK position. Lift the seat forward. Grease Type: No. 2 lithium grease Greasing the Bearings You can access the following components by raising the seat: • Serial plate 1. Park the machine on a level surface and disengage the blade-control switch. 2.
5. Engine Maintenance Pump grease into the fittings until grease begins to ooze out of the bearings. Servicing the Air Cleaner Service Interval: Before each use or daily—Check the air cleaner for dirty, loose or damaged parts. Every 50 hours—Service the air-cleaner paper element (more often under extremely dusty, dirty conditions). Every 100 hours—Replace the air-cleaner paper element (more often under extremely dusty, dirty conditions).
g023919 Figure 27 1. Air-cleaner latch 3. Paper element 2. Engine 4. Air-cleaner base Servicing the Engine Oil Oil Type: Detergent oil (API service SJ or higher) Crankcase Capacity: 1.9 L (64 oz) when the filter is changed Viscosity: See the table below. g027515 Figure 29 g017552 Figure 28 Checking the Engine-Oil Level Service Interval: Before each use or daily—Check the engine-oil level. 1.
Changing the Engine Oil and the Engine-Oil Filter Service Interval: Every 100 hours—Change the engine oil and the engine-oil filter. Note: The drain plug is attached to the drain hose. Note: Dispose the used oil at a recycling center. Fill with oil as specified in the “Viscosity Grades” table (Figure 28). 1. Park the machine so that the drain side is slightly lower than the opposite side to ensure that the oil drains completely. 2.
g027478 Figure 33 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, or cracks. Note: If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. Set the gap to 0.76 mm (0.030 inch).
Installing the Spark Plug Fuel System Maintenance Tighten the spark plug to 25 to 29 N·m (18 to 22 ft-lb). DANGER In certain conditions, gasoline is extremely flammable and highly explosive. A fire or explosion from gasoline can burn you and others and can damage property. • Perform any fuel-related maintenance when the engine is cold. Do this outdoors in an open area. Wipe up any gasoline that spills.
Electrical System Maintenance WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. g027959 Charging the Battery Removing the Battery WARNING Battery terminals or metal tools could short against metal machine components causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.
Charging the Battery WARNING Incorrect battery-cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Service Interval: Before storage—Charge the battery and disconnect the battery cables. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. 1. Remove the battery from the chassis; refer to Removing the Battery (page 35). 2.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component or circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1-30 amp, blade-type Service Interval: Every 25 hours—Check tire pressure. • Charge Circuit—F2-25 amp, blade-type 1. Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause uneven cut.
Mower Maintenance Releasing the Electric Brake Servicing the Cutting Blades The electric brake releases by manually rotating the link arms forward. Once the electric brake is energized the brake resets. Maintain sharp blades throughout the cutting season, because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding the grass turns it brown at the edges, which slows growth and increases the chance of disease.
3. Measure from the tip of the blade to the flat surface (Figure 44). g006530 Figure 42 1. Cutting edge 3. Wear/slot forming 2. Curved area 4. Damage g014973 Figure 44 Checking for Bent Blades 1. Blade (in position for measuring) Note: Park the machine on a level surface for the following procedure. 2. Level surface 3. Measured distance between blade and the surface (A) 1. 2. Raise the mower deck to the highest height-of-cut position. 4.
Removing the Blades Replace a blade if it hits a solid object, if the blade is out of balance, or if the blade is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. g014973 Figure 46 1. Hold the blade end using a rag or thickly padded glove. 2. Remove the blade bolt, curved washer, and blade from the spindle shaft (Figure 47). 1.
Note: If the blade is not balanced, file some metal off only the end of the sail area (Figure 48). g000553 Figure 49 1. Blade 3. 2. Balancer Repeat this procedure until the blade is balanced. g009682 Figure 50 Mower decks with 2 blades Installing the Blades 1. Install the blade onto the spindle shaft (Figure 47). Important: The curved part of the blade 1. Blades side to side 3. Outside cutting edges 2. Sail area of blade 4. Measure from the tip of the blade to the flat surface here.
Adjusting the Front-to-Rear Blade Slope Check the front-to-rear blade level any time you install the mower. If the front of the mower is more than 7.9 mm (5/16 inch) lower than the rear of the mower, adjust the blade level using the following procedure: 1. Park the machine on a level surface and disengage the blade-control switch. 2.
5. Removing the Mower Measure from the tip of the front blade to the flat surface, and the tip of the rear blade to the flat surface (Figure 53). Note: If the front blade tip is not 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip, adjust the front locknut. 6. To adjust the front-to-rear blade slope, rotate the adjustment nut in the front of the mower (Figure 55). Note: To raise the front of the mower, tighten the adjustment nut.
Replacing the Grass Deflector Service Interval: Before each use or daily—Inspect the grass deflector for damage. WARNING An uncovered discharge opening could allow the lawn mower to throw objects at you or bystanders, resulting in serious injury. Also, contact with the blade could occur. Never operate the machine without the grass deflector, the discharge cover, or the grass-collection system in place. g005077 Figure 57 1. Mower deck 2.
8. Insert the rod at the front of the grass deflector into the short standoff on the deck. Mower Belt Maintenance 9. Secure the rear end of the rod into the mower with a nut (3/8 inch) as shown in Figure 58. Inspecting the Belts Important: The grass deflector must be spring-loaded and in the down position. Lift the deflector up to test that it snaps to the full down position. Service Interval: Every 25 hours—Check the belts for wear or cracks.
7. Using a spring-removal tool, install the idler spring over the deck hook, and place tension on the idler pulley and mower belt (Figure 60). 8. Install the pulley covers (Figure 59). g014931 Figure 61 Mower decks with 3 blades g014930 Figure 60 Mower Decks with 2 Blades 1. Idler pulley 4. Spring 2. Mower belt 5. Engine pulley 3. Outside pulley 6. Spring-removal tool 46 1. Idler pulley 4. Spring 2. Mower belt 5. Engine pulley 3. Outside pulley 6.
Cleaning 7. Disengage the blade-control switch, shut off the engine, remove the ignition key, and wait for all moving parts to stop. Washing the Underside of the Mower 8. Turn the water off and remove the coupling from the washout fitting. Note: If the mower is not clean after a single washing, soak it and let it stand for 30 minutes. Then, repeat the process. Service Interval: After each use—Clean the mower-deck housing. 9.
Storage F. Important: Do not store Cleaning and Storage 1. 2. stabilizer/conditioned gasoline over 90 days. Disengage the blade-control switch, move the motion-control levers outward to the PARK position, shut off the engine, and remove the key. 10. Remove the spark plug(s) and check its condition; refer to Checking the Spark Plug (page 33). With the spark plug(s) removed from the engine, pour 2 tablespoons of engine oil into the spark plug hole.
Troubleshooting Problem The engine overheats. Possible Cause 1. The engine load is excessive. 1. Reduce the ground speed. 2. The oil level in the crankcase is low. 3. The cooling fins and air passages under the engine blower housing are plugged. 4. The air cleaner is dirty. 2. Add oil to the crankcase. 3. Remove the obstruction from the cooling fins and air passages. 5. Dirt, water, or stale fuel is in the fuel system. The starter does not crank.
Problem There is an abnormal vibration. The cutting height is uneven. Possible Cause 1. The engine-mounting bolts are loose. 1. Tighten the engine-mounting bolts. 2. The engine pulley, idler pulley, or blade pulley is loose. 3. The engine pulley is damaged. 4. The cutting blade(s) is/are bent or unbalanced. 5. A blade-mounting bolt is loose. 6. A blade spindle is bent. 2. Tighten the appropriate pulley. 5. Tighten the blade-mounting bolt. 6. Contact an Authorized Service Dealer. 1.
Schematics g028022 Electrical Diagram (Rev.
TimeCutter and TITAN Mowers The Toro Warranty Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Products listed below if defective in materials or workmanship. 1. Contact any Authorized Toro Service Dealer to arrange service at their dealership. To locate a dealer convenient to you, access our web site at www.Toro.com.