Form No. 3398-917 Rev B TimeCutter® SW 4200 or SW 5000 Riding Mower Model No. 74784—Serial No. 316000001 and Up Model No. 74790—Serial No. 316000001 and Up Register at www.Toro.com.
Introduction WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm. This machine is a ride-on, rotary-blade lawn mower intended to be used by homeowners in residential applications.
Fuel System Maintenance ................................... 37 Replacing the In-Line Fuel Filter ....................... 37 Electrical System Maintenance ........................... 38 Charging the Battery......................................... 38 Servicing the Fuses .......................................... 40 Drive System Maintenance .................................. 40 Checking the Tire Pressure............................... 40 Releasing the Electric Brake .............................
Safety • Do not operate the machine without deflector, discharge cover or entire grass collection system in place and working. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions, and pay attention to the safety alert symbol , which means Caution, Warning, or Danger—personal safety instruction. Failure to comply with the instructions may result in personal injury or death.
Towing Safety • Reduce speed and use extreme caution on slopes. • Do not make sudden turns or rapid speed changes. • Remove or mark obstacles such as rocks, tree • • • • • • • • Do not attach towed equipment except at the hitch point. limbs, etc. from the mowing area. Tall grass can hide obstacles. Avoid sudden starts when mowing uphill because the mower may tip backward. Be aware that loss of traction may occur going downhill.
Service • Never make any adjustments or repairs with the Safe Handling of Gasoline • Grass catcher components are subject to wear, engine running. damage, and deterioration, which could expose moving parts or allow objects to be thrown. Frequently check components and replace them with the manufacturers' recommended parts, when necessary. To avoid personal injury or property damage, use extra care when handling gasoline and other fuels. They are flammable and the vapors are explosive.
Toro Riding Mower Safety The following list contains safety information specific to Toro products or other safety information that you must know that may not be included in the ANSI standards. • Stop the engine, disengage the blade-control switch, remove key before and disconnect spark plug wire(s) performing any service, repairs, maintenance or adjustments. • Keep hands, feet, hair, and loose clothing away from attachment discharge area, underside of mower and any moving parts while engine is running.
Slope Indicator g011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal93-7009 93-7009 1. Warning—don't operate the mower with the deflector up or removed; keep the deflector in place. 2. Cutting/dismemberment hazard of hand or foot, mower blade—stay away from moving parts.
decal112-9840 112-9840 1. Read the Operator's Manual. 3. Remove the ignition key and read the instructions before servicing or performing maintenance. 2. Height-of-cut decaloemmarkt Manufacturer's Mark decal119-8871 119-8871 42 Inch Model 1. Indicates the blade is identified as a part from the original machine manufacturer. 1. Height-of-cut decal121-2989b 121-2989 1. Bypass lever position for pushing the machine decal119-8870 119-8870 50-inch and 54-inch Models 1. Height-of-cut 10 2.
decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking 7. Wear eye protection; explosive gases can cause blindness and other injuries. 3. Caustic liquid/chemical burn hazard 4. Wear eye protection. 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual.
decal131-3665 131-3665 1. Blade spinning 3. Read the Operator's Manual. 2. Reverse decal132-6863 132-6863 decal131-3954 131-3954 1. On decal132-0872 132-0872 2. Off decal131-3955 131-3955 1. On 2. Off 12 1. Thrown object hazard—keep bystanders away from the machine. 3. Severing hazard of hand or foot—keep away from moving parts. 2. Thrown object hazard, raised baffle—do not operate the machine with an open deck; use a bagger or a baffle. 4.
decal132-0870 132-0870 1. Warning—read the Operator's Manual. 3. Bodily harm hazard—no riders; look behind you when mowing in reverse. 5. Ramp tipping hazard—when loading onto a trailer, do not use dual ramps; only use a single ramp wide enough for the machine and that has an incline less than 15 degrees; back up the ramp (in reverse) and drive forward off the ramp. 2.
decal121-0772 121-0772 Models with 42 inch mower deck 1. Fast 2. Continuous-variable setting 4. Choke 5. Power take-off (PTO), blade-control switch 3.
decal121-0773 121-0773 Models with 50 inch mower deck 1. Fast 2. Continuous-variable setting 4. Choke 5. Power take-off (PTO), blade-control switch 3.
Product Overview g028251 Figure 6 1. Operating-in-reverse warning light 3. Fuel-presence window 2. Key Choice key (blue in color) Ignition Switch The ignition switch has 3 positions—OFF, RUN, and START . The key turns to the START position and moves back to the RUN position upon release. Turning the key to the OFF position stops the engine. Always remove the key when leaving the machine to prevent someone from accidentally starting the engine (Figure 5). g027935 Figure 4 1. Traction-control pedal 7.
Operation and when you lower it (away from you), it lowers to the ground. Adjust the height of cut only while the machine is not moving (Figure 14). Note: Determine the left and right sides of the machine from the normal operating position. Key Choice® Switch Adding Fuel This switch allows you to mow in reverse when it is activated. To activate it, turn the switch to the ON position and release it after the PTO is engaged. To deactivate it, disengage the PTO (Figure 6).
Add the correct amount of gasoline stabilizer/conditioner to the gasoline. DANGER In certain conditions during fueling, static electricity can be released, causing a spark that can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
40 to 50 hours of break-in time for new machines to develop full power and best performance. CAUTION This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. Think Safety First Please carefully read all of the safety instructions and decals in the safety section. Knowing this information could help you, your family, pets, or bystanders avoid injury. Wear hearing protection when operating this machine.
Testing the Safety-Interlock System 1. Sit in the seat with the engine off and ensure that the PTO switch is in the OFF position. 2. Turn the ignition key to the START position; the starter should crank. Do not start the engine or turn the engine off prior to step 3. 3. Turn the key to the ON position and push the SmartPark switch to the OFF position. The brake should disengage and the brake light should turn off. 4. blade-control switch in to disengage the blades.
Starting the Engine Operating the Blades Note: A warm or hot engine may not require choking. The blade-control switch engages and disengages power to the mower blades. This switch controls power to any attachments that draw power from the engine, including the mower deck and cutting blades. Important: Do not engage the starter for more than 10 seconds at a time. If the engine fails to start, allow a 60 second cool-down period between attempts.
Driving the Machine This machine has the characteristics of both a garden tractor and a zero-turn machine. Like a garden tractor, the machine has a foot pedal that controls the forward and reverse motion along with the speed, and it has a steering wheel that controls the direction and the turning radius. Like a zero-turn machine, the rear drive wheels operate independently of each other, enabling you to make sharp turns and to turn in different directions quickly.
DANGER A child or bystander could be backed over by a riding mower with blades engaged and cause serious personal injury or death. • Do not mow in reverse unless absolutely necessary. • Always look backward and down before backing up. • Use the KeyChoice switch only if you are certain no children or other bystanders will appear in the mowing area.
Positioning the Steering Wheel • Upper hole—use this position with the mower The steering wheel has 3 positions for operation and 1 full-up position. Use the full-up position for stepping on and off the machine and getting out of the seat. When operating the machine, position the steering wheel where you have the best control of the machine and are most comfortable. • Lower hole—use this position with the deck in the 63 mm (2-1/2 inch) and below height-of-cut positions (Figure 17). 1.
g010233 Figure 18 1. Anti-scalp roller 3. Flange nut 2. Bolt 4. Hole spacing g017303 Figure 19 1. Bypass-lever locations Pushing the Machine by Hand 2. Lever position for operating the machine Important: Always push the machine by hand. Do 6. not tow the machine, because damage may occur. This machine has an electric-brake mechanism. To push the machine, the ignition key needs to be in the RUN position. The battery needs to be charged and functioning for the electric brake to be disengaged.
Using the Grass Deflector Transporting the Machine The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets, or bystanders avoid injury.
Loading the Machine WARNING Loading a machine onto a trailer or truck increases the possibility of tip-over and could cause serious injury or death. Use extreme caution when loading or unloading machines onto a trailer or a truck. Use a full-width ramp that is wider than the machine for this procedure. Back the machine up the ramp and drive it forward down the ramp (Figure 21). • Use extreme caution when operating a machine on a ramp.
Operating Tips Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower in uncut grass. Always try to have 1 side of the mower free from uncut grass, which allows air to be drawn into the mower.
drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward. Keeping the Underside of the Mower Clean Clean clippings and dirt from the underside of the mower after each use. If grass and dirt build up inside the mower, cutting quality will eventually become unsatisfactory.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 5 hours • Change the engine oil. Before each use or daily • • • • Check the engine-oil level. Clean the air intake screen. Check the cutting blades. Inspect the grass deflector for damage. After each use • Check and clean the front of the mower. • Clean the mower housing.
Lubrication Raising the Front of the Machine Greasing the Bearings If you need to raise the front of the machine, use the very front edge as shown in Figure 23. Service Interval: Every 25 hours—Grease all the lubrication points. Important: To prevent damage to the steering mechanism, ensure that the very front edge of the machine is used for jacking points. Grease Type: No. 2 lithium grease 1. Park the machine on a level surface, and disengage the blade-control switch. 2.
Engine Maintenance Servicing the Air Cleaner Note: Service the air cleaner more frequently (every few hours) if operating conditions are extremely dusty or sandy. g027802 Figure 27 Removing the Elements 1. Park the machine on a level surface and disengage the blade-control switch (PTO). 2. Engage the parking brake, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. 4.
Servicing the Engine Oil Oil Type: Detergent oil (API service SF, SG, SH, SJ, or SL) Crankcase Capacity: 2.4 L (2.5 US qt) Viscosity: See the table below. g029683 Figure 28 Checking the Engine-Oil Level Service Interval: Before each use or daily Note: Check the oil when the engine is cold. WARNING Contact with hot surfaces may cause personal injury. g029368 Figure 29 Keep hands, feet, face, clothing, and other body parts away the muffler and other hot surfaces.
4. Drain the engine oil.
5. Change the engine oil filter (Figure 31). g027484 Figure 32 Servicing the Spark Plug g027477 Service Interval: Every 100 hours/Yearly (whichever comes first)—Check the spark plug(s). Figure 31 Note: Ensure that the oil-filter gasket touches Every 200 hours/Every 2 years (whichever comes first)—Replace the spark plug(s). the engine and then turn the filter an extra 3/4 turn. 6. Make sure that the air gap between the center and side electrodes is correct before installing the spark plug.
g027478 Figure 33 Note: Due to the deep recess around the spark plug, blowing out the cavity with compressed air is usually the most effective method for cleaning. The spark plug is most accessible when the blower housing is removed for cleaning. g028318 Figure 35 Checking the Spark Plug Important: Do not clean the spark plug(s). Always replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, or cracks.
Cleaning the Cooling System Fuel System Maintenance Clean the air intake screen from grass and debris before each use. 1. Disengage the blade-control switch and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Remove the air filter from the engine. 4. Remove the engine shroud. 5. To prevent debris entering the air intake, install the air filter to the filter base. 6.
Electrical System Maintenance WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. g027939 Charging the Battery Removing the Battery WARNING Battery terminals or metal tools could short against metal machine components, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury.
3. WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. • Always connect the positive (red) battery cable before connecting the negative (black) cable.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component or circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1-30 A, blade-type Service Interval: Every 25 hours—Check the tire pressure. • Charge Circuit—F2-25 A, blade-type 1. Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause uneven cut.
Mower Maintenance Releasing the Electric Brake Servicing the Cutting Blades The electric brake can be release by manually rotating the link arms forward. Once the electric brake is energized, the brake will reset. Maintain sharp and balanced blades throughout the cutting season, because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth, and increases the chance of disease.
3. Measure from the tip of the blade to the flat surface (Figure 44). g006530 Figure 42 1. Cutting edge 3. Wear/slot forming 2. Curved area 4. Damage g014973 Figure 44 Checking for Bent Blades 1. Blade (in position for measuring) Note: The machine must be on a level surface for the following procedure. 2. Level surface 3. Measured distance between blade and the surface (A) 1. 2. Raise the mower deck to the highest height-of-cut position, also considered the ‘transport’ position. 4.
g014973 Figure 46 g027833 1. Opposite blade edge (in position for measuring) Figure 47 2. Level surface 3. Second measured distance between blade and surface (B) 1. Sail area of the blade 2. Blade WARNING Sharpening the Blades A blade that is bent or damaged could break apart and could seriously injure or kill you or bystanders. 1. Use a file to sharpen the cutting edge at both ends of the blade (Figure 48). Note: Maintain the original angle.
Installing the Blades 1. Install the blade onto the spindle shaft (Figure 47). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. 2. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 47). 3. Torque the blade bolt to 47 to 88 N∙m (35 to 65 ft-lb).
g009658 Figure 53 Mower Decks with 2 Blades 1. Blades front to rear 2. Measure from the tip of the blade to the flat surface here. g027588 Figure 52 1. Hanger bracket 3. Rear nut 2. Side locking nut 9. Check the side-to-side adjustments again. Repeat this procedure until the measurements are correct. 10. Continue leveling the mower deck by checking the front-to-rear blade slope; refer to Adjusting the Front-to-Rear Blade Slope (page 45). g009659 Figure 54 Mower Decks with 3 Blades 1.
g014634 Figure 55 1. Adjusting rod 3. Locknut 2. Adjusting block g014635 7. Figure 56 To raise the front of the mower, tighten the adjustment nut. 1. Front support rod 8. To lower the front of the mower, loosen the adjustment nut. 2. Locking nut 9. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip (Figure 53 and Figure 54). 5. 10.
Note: Retain all parts for future installation. Mower Belt Maintenance Inspecting the Belts Service Interval: Every 25 hours—Check the belts for wear/cracks. Check the belts for cracks, frayed edges, burn marks, or any other damage. Replace damaged belts. Replacing the Mower-Deck Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. g014930 1.
6. Route the new belt around the engine pulley and mower pulleys (Figure 59 and Figure 60). 7. Using a spring removal tool, (Toro Part No. 92-5771), install the idler spring over the deck hook and placing tension on the idler pulley and mower belt (Figure 59 and Figure 60). 8. Replacing the Grass Deflector Service Interval: Before each use or daily—Inspect the grass deflector for damage. WARNING Install the pulley covers (Figure 58).
8. Insert the rod at the front of the grass deflector into the short standoff on the deck. 9. Secure the rear end of the rod into the mower with a nut (3/8 inch) as shown in Figure 61. Cleaning Cleaning Under the Front of the Machine Important: The grass deflector must be spring-loaded and in the down position. Lift the deflector up to test that it snaps to the full down position. Service Interval: After each use—Check and clean the front of the mower.
Storage Cleaning and Storage 1. Disengage the blade-control switch, shut off the engine, and remove the key. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine. Clean dirt and chaff from the outside of the engine cylinder head fins and blower housing. Important: You can wash the machine with mild detergent and water. Do not pressure wash the machine.
12. Clean any dirt and chaff from the top of the mower. 13. Scrape any heavy buildup of grass and dirt from the underside of the mower, then wash the mower with a garden hose. 14. Check the condition of the drive and mower belts. 15. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is worn or damaged. 16. Paint all scratched or bare metal surfaces. Paint is available from your Authorized Service Dealer. 17. Store the machine in a clean, dry garage or storage area.
Troubleshooting Problem The engine overheats. Possible Cause 1. The engine load is excessive. 1. Reduce ground speed. 2. The oil level in the crankcase is low. 3. The cooling fins and air passages under the engine blower housing are plugged. 4. The air cleaner is dirty. 2. Add oil to the crankcase. 3. Remove the obstruction from the cooling fins and air passages. 5. Dirt, water, or stale fuel is in fuel system. The starter does not crank.
Problem There is abnormal vibration. The cutting height is uneven. Possible Cause 1. The engine mounting bolts are loose. 1. Tighten the engine mounting bolts. 2. The engine pulley, idler pulley, or blade pulley is loose. 3. The engine pulley is damaged. 4. The cutting blade(s) is/are bent or unbalanced. 5. A blade mounting bolt is loose. 6. A blade spindle is bent. 2. Tighten the appropriate pulley. 5. Tighten the blade mounting bolt. 6. Contact an Authorized Service Dealer. 1.
Schematics g027754 Electrical Diagram (Rev.
Notes:
TimeCutter and TITAN Mowers The Toro Warranty Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Products listed below if defective in materials or workmanship. 1. Contact any Authorized Toro Service Dealer to arrange service at their dealership. To locate a dealer convenient to you, access our web site at www.Toro.com.