Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74815

FormNo.3360-101RevA

ZeroTurnRadiusMowers

Allmodels

SetupInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Deectorassembly

Rod1

Spring

Cotterpin

Installthedischargedeector.

Sidedischargebafe

Carriagebolt(5/16x3/4inch)

Hex-headbolt(5/16x3/4inch)

Locknut(5/16inch)

Holecoverdecal3

Converttosidedischarge(optional).

IgnitionKey1

Hosecoupling1

Operator’sManual

EngineOperator’sManual

OperatorTrainingMaterial

Completethesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

CheckingTirePressure

NoPartsRequired

Procedure

1.Checkthetirepressureinthedrivetires.Proper

inationfordrivetiresis13psi(90kPa).

2.Adjustifnecessary.

FasteningtheSeat

NoPartsRequired

Procedure

1.Removethenutandboltfromthelooseendofthe

lanyard.

2.Tiltseatdownwardandalignlanyardtotheholein

thesideoftheseat(seeFigure1).

3.Installboltandnut.Tightenboltandthenloosen

nut1/4-1/2turnsothatlanyardendrotatesfreely.

Verifythatlanyardisfreetorotateonbothendsso

thatitpullsstraightwhilesupportingtheseat..

PrintedintheUSA.OriginalInstructions(EN)

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3360-101 Rev A Zero Turn Radius Mowers All models Setup Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 7 8 9 Description Use Qty.
PAGE 2
in the table below and charge the battery for the recommended time interval to bring the charge up to a full charge of 12.6 volts or greater. Important: Make sure the negative battery cables are disconnected and the battery charger used for charging the battery has an output of 16 volts and 7 amps or less to avoid damaging the battery (see chart for recommended charger settings). Figure 1 1. Seat assembly 2. Seat track studs 3.
PAGE 3
4 Installing the Motion Control Levers No Parts Required Procedure Figure 3 1. Motion control lever 1. Remove the bottom 3/8 x 1 inch bolt and spring disc washer from the control arm shaft. Loosen the upper 3/8 x 1 inch bolt and spring disc washer in the control lever so that the lever can rotate Figure 2. 2. Hardware 5.
PAGE 4
5 Servicing the Engine No Parts Required Procedure Engine is shipped with oil; check oil level and if necessary fill to the appropriate level with oil as specified in Engine Owner’s Manual. Figure 5 1. Engine 6 2. Expansion tank 4. Replace expansion tank cap and tighten until snug. Do Not overtighten. Servicing the Hydraulic Oil 7 No Parts Required Procedure The machine is shipped with hydraulic oil. Verify level on Expansion Tank (see Figure 5). Installing the Discharge Deflector 1.
PAGE 5
8 Converting to Side Discharge (optional) Parts needed for this procedure: 1 Side discharge baffle 2 Carriage bolt (5/16 x 3/4 inch) 2 Hex-head bolt (5/16 x 3/4 inch) 4 Lock nut (5/16 inch) 3 Hole cover decal Procedure Figure 6 1. Rod 2. Spring 3. Discharge deflector The mower deck is built for optimum mulching performance at the factory. If the mower is to be converted to side discharge, use the loose parts listed above and See the Operator’s Manual for the proper procedure. 4. Mower deck 5.
PAGE 6
9 Completing the Setup Parts needed for this procedure: 1 Ignition Key 1 Hose coupling 1 Operator’s Manual 1 Engine Operator’s Manual 1 Operator Training Material Checking the Mower Adjustment The mower deck was leveled at the factory. If the mower is not cutting level, adjust the side-to-side level and the front-to-rear blade slope. See the Operator’s Manual for the proper procedure.
PAGE 7
PAGE 8