Form No. 3400-805 Rev B TITAN® ZX 4800 or 5400 Zero-Turn-Radius Riding Mower Model No. 74846—Serial No. 316000001 and Up Model No. 74848—Serial No. 316000001 and Up Register at www.Toro.com.
This machine is a ride-on, rotary-blade lawnmower intended to be used by homeowners in residential applications. It is primarily designed for cutting grass on well-maintained lawns. It is not designed for cutting brush, mowing grass and other growth alongside highways, or for agricultural uses. This product complies with all relevant European directives; for details, please see the separate product specific Declaration of Conformity (DOC) sheet.
WARNING Removing standard original equipment parts and accessories may alter the warranty, traction, and safety of the machine. Failure to use original Toro parts could cause serious injury or death. Making unauthorized changes to the engine, fuel or venting system, may violate EPA and CARB regulations. Replace all parts including, but not limited to, tires, belts, blades, and fuel system components with original Toro parts.
Contents Electrical System Maintenance ........................... 41 Servicing the Battery......................................... 41 Servicing the Fuses .......................................... 42 Drive System Maintenance .................................. 43 Checking the Tire Pressure............................... 43 Hydraulic System Maintenance ........................... 44 Checking the Hydraulic-Fluid Level................... 44 Changing the Hydraulic Filter and Fluid ............................
Safety • Thoroughly inspect the area where the equipment The following instructions are from the EN standard EN ISO 5395:2013. • Warning-Fuel is highly flammable. is to be used and remove all objects which may be thrown by the machine. – Store fuel in containers specifically designed for this purpose. Improperly using or maintaining the machine can result in injury.
• Allow the engine to cool before storing in any • Watch out for traffic when crossing or near • • • • • • • • • • enclosure. roadways. Stop the blades rotating before crossing surfaces other than grass. When using any attachments, never direct discharge of material toward bystanders nor allow anyone near the machine while in operation. Never operate the machine with damaged guards or without safety protective devices in place. Do not change the engine governor settings or overspeed the engine.
Sound Pressure • Remove or mark obstacles such as rocks, tree limbs, etc. from mowing area. Tall grass can hide obstacles. This unit has a sound pressure level at the operator’s ear of 92 dBA, which includes an Uncertainty Value (K) of 1 dBA. • Watch for ditches, holes, rocks dips, and rises that change the operating angle, as rough terrain could overturn the machine. Sound power level was determined according to the procedures outlined in EN ISO 5395:2013.
Model 74848 Sound Power This unit has a guaranteed sound power level of 105 dBA, which includes an Uncertainty Value (K) of 1 dBA. Sound power level was determined according to the procedures outlined in ISO 11094. Sound Pressure This unit has a sound pressure level at the operator’s ear of 92 dBA, which includes an Uncertainty Value (K) of 1 dBA. Sound power level was determined according to the procedures outlined in EN ISO 5395:2013. Hand-Arm Vibration Measured vibration level for left hand = 5.
Slope Indicator g011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decaloemmarkt Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. decal99-8936 99-8936 1. Machine speed 4. NEUTRAL 2. FAST 3. SLOW 5. REVERSE decal115-9625 115-9625 1. Parking brake—disengaged 2.
decal117-1194 117-1194 1. Engine decal130-0655 130-0655 1. Fuel tank 2. Full 3. Half 4. Empty decal130-0731 130-0731 1. Warning—thrown object hazard; keep the deflector shield in place. decal130-0654 130-0654 1. Transport—lock 3. Height of cut 2. Transport—unlock 11 2. Cutting hazard of hand or foot, mower blade—keep away from moving parts.
decal130-0765 130-0765 1. Read the Operator's Manual. 3. Remove the key from the ignition and read the Operator's Manual before permorning maintenance. 2. Height-of-cut selection decal130-6927 130-6927 1. Warning—always use the ROPS and wear the seat belt when seated in the operator's position. decal130-6922 130-6922 1. Bypass lever position for operating the machine. 2. Bypass lever position for pushing the machine.
decal132-0873 132-0873 1. Thrown object hazard—keep bystanders away from the machine. 3. Cutting/dismemberment of hand or foot—stay away from moving parts. 2. Thrown object hazard, mower—do not operate the without 4. Entanglement hazard, belt—keep all guards in place. deflector, discharge cover, or grass collection system in place. decal130-6996 130-6996 1. Read the Operator's 4. Check the hydraulic oil Manual for information on every 25 hours maintenance. 2. Check the engine oil every 5.
decal132-0871 132-0871 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in those conditions on that day and at that site.
Product Overview g024328 Figure 4 1. Drive wheel 2. Operator seat 4. Motion-control levers 5. Parking brake 7. Front caster wheel 8. Anti-scalp roller 3. Rollover Protection System (ROPS) 6. Footrest 9. Foot pedal deck lift and height of cut 15 10.
Controls switch (PTO) is engaged. Use these times for scheduling regular maintenance (Figure 5). Become familiar with all the controls before you start the engine and operate the machine (Figure 5). Fuel Gauge The fuel window located below the operator position can be used to verify the level of gasoline in the tank (Figure 6). g017722 Figure 5 g020264 1. Throttle control 4. Ignition switch 2. Choke 5. Blade-control switch (PTO) Figure 6 1. Fuel-gauge window 3.
Attachments/Accessories Operation A selection of Toro approved attachments and accessories is available for use with the machine to enhance and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www.Toro.com for a list of all approved attachments and accessories. Note: Determine the left and right sides of the machine from the normal operating position.
Add the correct amount of gas stabilizer/conditioner to the gas. WARNING Gasoline is harmful or fatal if swallowed. Long-term exposure to vapors can cause serious injury and illness. Note: A fuel stabilizer/conditioner is most effective • Avoid prolonged breathing of vapors. when mixed with fresh gasoline. To minimize the chance of varnish deposits in the fuel system, use fuel stabilizer at all times. • Keep face away from nozzle and gas tank or conditioner opening.
Think Safety First CAUTION This machine produces sound levels in excess of 85 dBA at the operator’s ear and can cause hearing loss through extended periods of exposure. Please read all safety instructions and symbols in the safety section. Knowing this information could help you or bystanders avoid injury. DANGER Wear hearing protection when operating this machine. Operating the machine on wet grass or steep slopes can cause sliding and loss of control.
Understanding the Safety-Interlock System Checking the Engine-Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine-Oil Level (page 37). WARNING If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. • Do not tamper with the interlock switches.
Operating the Throttle Operating the Ignition Switch The throttle control can be moved between the SLOW and FAST positions (Figure 12). 1. Always use the FAST position when turning on the mower deck with the blade-control switch (PTO). Turn the ignition key to the START position (Figure 14). Note: When the engines starts, release the key. Note: Additional starting cycles may be required when starting the engine for the first time after the fuel system has been without fuel completely.
g027641 Figure 16 g027640 Figure 15 Operating the Blade-Control Switch (PTO) Stopping the Engine The blade-control switch (PTO) starts and stops the mower blades and any powered attachments. CAUTION Injury can occur if children or bystanders move or attempt to operate the machine while it is unattended. Engaging the Blade-Control Switch (PTO) Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes.
g008945 Figure 17 Disengaging the Blade-Control Switch (PTO) g009174 Figure 18 g004532 Figure 19 Driving the Machine 1. Motion-control lever—NEUTRAL-LOCK position 4. Backward 2. Center, unlocked position 5. Front of the machine 3. Forward The throttle control regulates the engine speed as measured in rpm (revolutions per minute). Place the throttle control in the FAST position for best performance. Always operate in the full-throttle position when mowing.
Stopping the Machine WARNING Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Always remove the ignition key and move the motion-control levers outward to the PARK position when leaving the machine unattended, even if just for a few minutes. To stop the machine, move the traction-control levers to the NEUTRAL position and move to the locked position, disengage the blade-control switch (PTO), and turn the ignition key to the OFF position.
g024410 Figure 23 g024409 1. Deck-lift pedal 3. Height-of-cut positions 2. Handle 4. Pin Figure 22 Transport Lock Position Adjusting the Anti-Scalp Rollers Adjusting the Height of Cut Whenever you change the height of cut, it is recommended to adjust the height of the anti-scalp rollers. 1. Disengage the blade-control switch (PTO), move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. 2.
4. Align the bolt and anti-scalp roller in the hole of the bracket that matched the closest height-of-cut position (Figure 24). 5. Insert the bolt into the bracket hole and secure the bolt and anti-scalp roller with the flange nut (Figure 24). Positioning the Seat The seat can move forward and backward (Figure 25). Position the seat where you have the best control of the machine and are most comfortable.
Converting the 48-Inch Mower to Side Discharge The mower deck and mower blades shipped with this machine were designed for optimum mulching and side-discharge performance. Install the fasteners into the same holes in the deck that they were originally removed from. This ensure no holes are left open when the deck is operated. DANGER Open holes in the mower expose you and others to thrown debris. Debris thrown out of holes in the mower can cause injury.
6. Remove the carriage bolt and locknut on the side wall of the mower deck securing the left baffle to the deck. 7. Remove the left baffle from the mower deck as shown in Figure 28. 8. Remove the carriage bolt (5/16 x 3/4 inch) and locknut (5/16 inch) on the rear wall of the mower deck securing the baffle to the deck (Figure 29). g012805 Figure 30 1. Locknut (5/16 inch) 3. Welded posts, right baffle 2. Right baffle 11.
Converting the 54-Inch Mower to Side Discharge 7. Remove the left baffle from the mower deck (Figure 32). 8. Locate the 2 bolts in loose parts and use the existing locknuts and install these fasteners into the holes shown in Figure 32 on the mower deck to prevent flying debris. Install the fasteners into the same holes in the deck as they were originally removed from. This ensures that no holes are left open when the deck is operated.
10. Locate the baffle guard at the front edge of the side discharge opening (Figure 33). 11. Remove the fasteners securing the baffle guard and the right baffle to the mower deck (Figure 33). Note: Remove the baffle guard and retain all fasteners. 12. Remove the 2 locknuts (5/16 inch) securing the welded posts of the right baffle to the top of the mower deck at center and right of center positions (Figure 34). g010703 Figure 35 1. Carriage bolt 3. Cutoff baffle 2.
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets, or bystanders avoid injury. g028043 Figure 37 1. Back the machine up the ramp.
g027996 Figure 38 1. Full-width ramp in stowed position 4. Ramp is at least 4 times as long as the height of the trailer or truck bed to the ground 2. Side view of full-width ramp in loading position 5. H= height of the trailer or truck bed to the ground 3. Not greater than 15 degrees 6.
Cutting Long Grass Operating Tips If the grass is ever allowed to grow slightly longer than normal, or if it contains a high degree of moisture, raise the cutting height higher than usual and cut the grass at this setting. Then cut the grass again using the lower, normal setting. Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. After the first 50 hours • Change the hydraulic filter and fluid. Before each use or daily • • • • • • Check the safety-interlock system. Clean and check the air-cleaner element. Check the engine-oil level. Clean the air-intake screen. Check the mower blades. Inspect the grass deflector for damage. After each use • Clean the mower housing.
Pre-Maintenance Procedures Service-Interval Chart decal115-9630 Figure 39 Located on the seat pan underside 1. Read the Operator's Manual before performing any maintenance. 2. Check the engine oil every 8 hours. 4. Check the hydraulic oil every 25 hours. 3. Check the drive wheel tire pressure every 25 hours. 6. Lubricate the caster wheel every 25 hours. 5. Check the caster wheel tire pressure every 25 hours.
Engine Maintenance Lubrication WARNING Greasing the Bearings Contact with hot surfaces may cause personal injury. Service Interval: Every 25 hours—Grease all lubrication points. Keep hands, feet, face, clothing and other body parts away the muffler and other hot surfaces. Grease Type: No. 2 lithium grease 1. Park the machine on a level surface and disengage the blade-control switch. 2.
g010686 Figure 43 Note: Using multi grade oils (5W-20, 10W-30, and 10W-40) will increase oil consumption. Check oil level more frequently when using them. g015155 Figure 42 1. Cover Checking the Engine-Oil Level 3. Hose clamp Service Interval: Before each use or daily 2. Paper element Note: Check the oil when the engine is cold. Cleaning the Element WARNING Contact with hot surfaces may cause personal injury.
Changing the Engine Oil Service Interval: After the first 8 hours—Change the engine oil. Every 100 hours—Change the engine oil (more often in dusty, dirty conditions). Note: Dispose of the used oil at a recycling center. 1. Park the machine so that the drain side is slightly lower than the opposite side to ensure the oil drains completely. 2. Disengage the PTO, move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. 3.
g027660 Figure 46 Changing the Engine-Oil Filter g027477 Figure 47 Service Interval: Every 200 hours—Change the engine-oil filter (more often in dusty, dirty conditions). Note: Ensure the oil filter gasket touches the engine and then an extra 3/4 turn is completed. Note: Change the engine-oil filter more frequently 3. when operating conditions are extremely dusty or sandy. 1. Drain the oil from the engine. 2. Change the engine-oil filter (Figure 47).
3. Remove the spark plug (Figure 48). g027478 Figure 48 Checking the Spark Plug Important: Never clean the spark plug(s). Always replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, or cracks. g027661 Figure 50 If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. Cleaning the Cooling System Set the gap to 0.03 inches (0.76 mm).
Fuel System Maintenance Electrical System Maintenance Replacing the Fuel Filter Servicing the Battery Service Interval: Every 100 hours/Yearly (whichever comes first) (more often under dusty, dirty conditions). Service Interval: Monthly DANGER 1. Disengage the blade-control switch (PTO), move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. Battery electrolyte contains sulfuric acid which is a deadly poison and causes severe burns. 2.
Important: Always keep the battery fully charged. This is especially important to prevent battery damage when the temperature is below 32°F (0°C). 1. Charge battery for 10 to 15 minutes at 25 to 30 amps or 30 minutes at 10 amps. 2. When the battery is fully charged, unplug the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Figure 53). 3. Install the battery in the machine and connect the battery cables. g027672 Figure 52 4.
Drive System Maintenance Checking the Tire Pressure Service Interval: Every 25 hours—Check tire pressure. Maintain the air pressure in the front and rear tires as specified. Uneven tire pressure can cause uneven cut. Check the pressure at the valve stem (Figure 56). Check the tires when they are cold to get the most accurate pressure reading. Refer to the maximum pressure suggested by the tire manufacturer on the sidewall of the caster wheel tires. Inflate the rear drive wheel tires to 90 kPa (13 psi).
Removing the Hydraulic Filters Hydraulic System Maintenance Important: When the hydraulic filter is removed, all of the hydraulic fluid in each transaxle will drain out. Use a container that holds 4.495 L (152 oz) or larger. 1. Shut off the engine, wait for all moving parts to stop, allow the engine to cool, remove the key, and engage the parking brake. 2. Locate the filter and guards on each transaxle drive system and remove the 3 screws securing the filter guard (Figure 58).
3. Bleeding the Hydraulic System Slowly pour the specified fluid through the expansion reservoir until fluid comes out of a vent-plug hole. 4. Install the vent plug and torque it to 20 N•m (180 in-lb). 5. Continue to add fluid through the expansion reservoir until fluid comes out of the remaining vent-plug hole on the second transmission. 6. Install the second vent plug and torque it to 20 N•m (180 in-lb). 7.
Mower Deck Maintenance Servicing the Cutting Blades Maintain sharp blades throughout the cutting season, because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth, and increases the chance of disease. g006530 Figure 61 Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary.
3. Measure from the tip of the blade to the flat surface (Figure 63). g009680 Figure 65 1. Opposite blade edge (in position for measuring) g009680 Figure 63 2. Level surface 3. Second measured distance between blade and surface (B) 1. Blade (in position for measuring) 2. Level surface 3. Measured distance between blade and the surface (A) 4. A. Rotate the same blade 180 degrees so that the opposing cutting edge is now in the same position (Figure 64).
3. Repeat this procedure until the blade is balanced. Installing the Blades 1. Install the blade onto the spindle shaft (Figure 66). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. g010341 3. Curved washer 4. Blade bolt 3. Torque the blade bolt to 135 to 150 N•m (100 to 110 ft-lb). Ensure that the mower deck is level any time you install the mower deck or when you see an uneven cut on your lawn.
g007202 g007199 Figure 69 1. Blades side to side Figure 70 3. Measure from the tip of the blade to the flat surface here. 1. Blades front to rear 2. Outside cutting edges 2. Outside cutting edges Checking the Front-to-Rear Blade Slope Leveling the Mower Deck Check the front-to-rear blade level any time you install the mower. If the front of the mower is more than 7.9 mm (5/16 inch) lower than the rear of the mower, adjust the blade level using the following instructions: 1.
Replacing the Mower Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. 1. Disengage the blade-control switch (PTO), move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
11. Removing the Mower Deck Install the new belt around the mower pulleys and the clutch pulley under the engine (Figure 73). 1. WARNING Remove the hairpin cotter and washer securing the link pin to the frame and deck, and remove the link bar (Figure 74). The spring is under tension when installed and can cause personal injury. Be careful when removing the belt. 12. Using a spring-removal tool, (Toro Part No.
Installing the Mower Deck 1. Park the machine on a level surface and disengage the blade-control switch. 2. Move the motion-control levers outward to the NEUTRAL-LOCK position, shut off the engine, remove the key, set the parking brake, and wait for all moving parts to stop before leaving the operating position. 3. Slide the mower under the machine. 4. Lower the height-of-cut lever to the lowest position. 5. Place the height-of-cut pin in the lock position for lowest height of cut. 6.
Cleaning Washing the Underside of the Mower Service Interval: After each use—Clean the mower housing. Wash the underside of the mower after each use to prevent grass buildup for improved mulch action and clipping dispersal. 1. Park the machine on a level surface and disengage the blade-control switch. 2. Move the motion-control levers outward to the NEUTRAL-LOCK position, shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3.
4. Lower the mower to the lowest height of cut. 5. Sit on the seat, start the engine, engage the blade-control switch, and let the mower run for 1 to 3 minutes. Storage Cleaning and Storage 6. Disengage the blade-control switch, shut off the engine, remove the ignition key, and wait for all moving parts to stop. 1. Disengage the blade-control switch (PTO), set the parking brake, turn the ignition key to the OFF position, and remove the key. 7.
B. Run the engine to distribute conditioned fuel through the fuel system (5 minutes). C. Shut off the engine, allow it to cool, and drain the fuel tank. D. Restart the engine and run it until it stops. E. Dispose of fuel properly. Recycle the fuel according to local codes. Important: Do not store stabilizer/conditioned fuel over 90 days. 13. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged. 14. Paint all scratched or bare metal surfaces.
Troubleshooting Problem The starter does not crank Engine does not start, starts hard, or fails to keep running Possible Cause 1. Blade-control switch (PTO) is engaged. 1. Move the blade-control switch (PTO) to disengaged. 2. Parking brake is not on. 3. Drive levers are not in NEUTRAL-LOCK position. 4. Operator is not seated. 5. Battery is dead. 6. Electrical connections are corroded or loose. 7. Fuse is blown. 8. Relay or switch is defective. 2. Set the parking brake. 3.
Problem Machine does not drive. Abnormal vibration. Uneven cutting height. Possible Cause 1. By pass valves is not closed tight. 1. Tighten the by pass valves. 2. 3. 4. 5. 2. 3. 4. 5. Pump belt is worn, loose or broken. Pump belt is off a pulley. Broken or missing idler spring. Hydraulic oil level is low or too hot. Change the belt. Change the belt. Replace the spring. Add hydraulic oil to reservoirs or let it cool down. 1. Cutting blade(s) is/are bent or unbalanced. 1.
Schematics g028048 Wire Diagram (Rev.
International Distributor List Distributor: Agrolanc Kft Asian American Industrial (AAI) B-Ray Corporation Brisa Goods LLC Casco Sales Company Ceres S.A. CSSC Turf Equipment (pvt) Ltd. Cyril Johnston & Co. Cyril Johnston & Co. Fat Dragon Femco S.A. FIVEMANS New-Tech Co., Ltd ForGarder OU G.Y.K. Company Ltd. Geomechaniki of Athens Golf international Turizm Hako Ground and Garden Hako Ground and Garden Hayter Limited (U.K.) Hydroturf Int. Co Dubai Hydroturf Egypt LLC Irrimac Irrigation Products Int'l Pvt Ltd.
TimeCutter and TITAN Mowers The Toro Warranty Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Products listed below if defective in materials or workmanship. 1. Contact any Authorized Toro Service Dealer to arrange service at their dealership. To locate a dealer convenient to you, access our web site at www.Toro.com.
