Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74846

FormNo.3394-403RevA

TITAN

ZXRidingMower

ModelNo.74846—SerialNo.315000001andUp

ModelNo.74848—SerialNo.315000001andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Connectthebattery.

Rearhitch1

Bolt(5/16x2-1/2inches)

Locknut(5/16inch)

Installtherearhitch.

Nopartsrequired

–

Setupthemotion-controlleversandthe

seat.

Rollbar1

Rollbarsupport2

Reinforcingbracket

ROPSplates

Bolt(1/2x3–1/2inches)

Bolt(1/2x4–1/2inches)

Hexlocknut(1/2inch)

Flatwasher(1/2inch)

Thrustwasher4

Flangelocknut(1/2inch)

Bolt(5/16x3–3/4inches)

Flangelocknut(5/16inch,maybe

pre-installed)

Flatwasher(5/16inch)

InstalltheRollOverProtectionSystem

(ROPS).

Nopartsrequired

–

Checkthemoweradjustment.

Ignitionkey1

Operator'sManual

EngineOperator'sManual

Completethesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3394-403*A

Summary of content (8 pages)

PAGE 1
Form No. 3394-403 Rev A TITAN® ZX Riding Mower Model No. 74846—Serial No. 315000001 and Up Model No. 74848—Serial No. 315000001 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Use Qty. 1 No parts required – Connect the battery. 2 Rear hitch Bolt (5/16 x 2-1/2 inches) Locknut (5/16 inch) 1 2 2 Install the rear hitch. 3 No parts required – Set up the motion-control levers and the seat.
PAGE 2
1 2 Connecting the Battery Installing the Rear Hitch No Parts Required Parts needed for this procedure: Procedure 1. Locate the battery and negative battery cable. 1 Rear hitch 2 Bolt (5/16 x 2-1/2 inches) 2 Locknut (5/16 inch) 2. Remove the plastic cap from the negative battery post. 3. Remove the fasteners on the negative battery cable, and use them to secure the negative battery cable to the negative battery post (Figure 1).
PAGE 3
A B C D E F Setting up the Motion-control Levers and the Seat No Parts Required Procedure 1. Locate the motion-control levers attached, but folded down on the machine. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3. Raise the motion control levers to the upright position. 4. Align the holes in the motion-control lever with the holes in the control-arm shaft, and install the bolt and washer removed previously. Repeat this for both controls levers.
PAGE 4
13 Installing the Roll Over Protection System (ROPS) 14 Parts needed for this procedure: 1 Rollbar 2 Rollbar support 2 Reinforcing bracket 4 ROPS plates 10 Bolt (1/2 x 3–1/2 inches) 2 Bolt (1/2 x 4–1/2 inches) 8 Hex locknut (1/2 inch) 8 Flat washer (1/2 inch) 4 Thrust washer 10 Flange locknut (1/2 inch) 15 g028588 Figure 6 1. Bolt (1/2 x 3–1/2 inches) (2) 9. Flange locknut (1/2 inch) (2) 2. Thrush washer (4) 10. Reinforcing bracket (2) 3. Rollbar support 11.
PAGE 5
Making Final Adjustments 1. Tighten the fasteners in the order specified in the following table. Figure 6,Figure 7, and Figure 8 will help identify the parts. 1 2 3 2 4 5 g028544 Sequence Description Torque 1 Four bolts on each side attaching the pivot brackets to the rollbar and rollbar support. 400 ± 40 in-lbs (45 ±.4 N-m) 2 Two bolts on each side attaching the rollbar support to the frame and the rollbar support to the brace .
PAGE 6
5 Checking the Mower Adjustment No Parts Required Procedure Adjust the side-to-side level and the front-to-rear blade slope. Use the relevant procedures in the Operator's Manual to verify that the deck is level, and make any adjustments as necessary. Refer to the Operator's Manual for more information.
PAGE 7
Notes: 7
PAGE 8