Setup Instructions

ManualsBrandsToro ManualsRiding EquipmentToro 74920

FormNo.3372-849RevA

TITANZX4820andZX5420Zero-Turn-RadiusRiding

Mower

ModelNo.74920—SerialNo.312000001andUp

ModelNo.74924—SerialNo.312000001andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Setupthemotioncontrollevers.

Rollbar1

Rollbarsupport2

Pivotbracket4

Flatspacer4

Pivotpinwithhairpinandlanyard2

Reinforcingbracket

Largewasher4

Bolt(1/2x4–1/2inches)

Bolt(1/2x3–1/2inches)

Cylindricalspacer

Flatwasher(1/2inch)

Flangelocknut(1/2inch)

Hexlocknut(1/2inch)

Flangelocknut(5/16inch,maybe

pre-installed)

Conicalrubberbumper(maybe

pre-installed)

Smallrubberbumper(maybe

pre-installed)

Bolt(5/16x3–3/4inch)

Flatwasher(5/16inch)

Flangelocknut(5/16inch)

InstalltheRollOverProtectionSystem

(ROPS).

Hosecoupling(notincludedwithCE

models)

Cutoffbafe(CEmodelsonly)

Bolt(5/16x5/8inch,54inchCEunits

only)

IgnitionKey1

Operator'sManual

EngineOperator'sManual

OperatorTrainingMaterial

Completethesetup.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3372-849 Rev A TITAN ZX4820 and ZX5420 Zero-Turn-Radius Riding Mower Model No. 74920—Serial No. 312000001 and Up Model No. 74924—Serial No. 312000001 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 © 2012—The Toro® Company 8111 Lyndale Avenue South Bloomington, MN 55420 Description Qty. Use No parts required – Connect the battery. No parts required – Set up the motion control levers.
PAGE 2
Note: Determine the left and right sides of the machine from the normal operating position. 1 3 5 4 2 Connecting the Battery 1 No Parts Required Procedure 1. Locate the battery and negative battery cable in the center of the machine. G010257 2. Remove the black plastic cap from the negative battery post. Remove the fasteners from the negative battery cable and use them to secure the negative battery cable to the negative battery post (Figure 1). Figure 1 1. Bolt 4. Negative battery post 2.
PAGE 3
A C B C C D G010258 Figure 2 A. With the motion control levers in the outward, neutral lock position, remove the hairpin cotters on the seat rod securing the seat to the machine. B. Slide the seat rod out from the brackets and seat frame. C. Rotate the seat 180 degrees and install it into the bracket you removed it from, using the rod and hairpin cotters removed previously. D. Connect the interlock switch cable to the seat. E. Lower the seat into the operating position. 5.
PAGE 4
3 13 14 Installing the Roll Over Protection System (ROPS) 15 Parts needed for this procedure: 1 Rollbar 2 Rollbar support 4 Pivot bracket 4 Flat spacer 2 Pivot pin with hairpin and lanyard 2 Reinforcing bracket 4 Large washer 2 Bolt (1/2 x 4–1/2 inches) 8 Bolt (1/2 x 3–1/2 inches) 2 Cylindrical spacer 4 Flat washer (1/2 inch) 3. Rollbar support 11. Reinforcing bracket (2) 8 Flange locknut (1/2 inch) 4. Cutout faces the rear 12.
PAGE 5
Note: Ensure that the tab to which the lanyard is attached is angled away from the surface of the pivot bracket. Figure 5 1. Bolt (1/2 x 3–1/2 inches) (4) 4. Flat spacer (4) 2. Flat washer (4) 5. Flange locknut (4) 3. Pivot bracket, notch facing up (4) 6. Rollbar, cutout facing down Figure 7 1. Bolt (1/2 x 3–1/2 inch) (2) 3. Flange locknut (2) 2. Pivot pin with hairpin and lanyard (2) Attaching the Rollbar 1. Insert the cylindrical spacer in the pivot holes in both rollbar supports (Figure 6). 4.
PAGE 6
Sequence Description Torque 1 Three bolts on each side attaching the pivot brackets to the rollbar and rollbar support. Ensure that the tab to which the lanyard is attached is pointed upward. 400 ± 40 in-lbs (45 ±.4 N-m) 2 Two bolts on each side attaching the rollbar support to the frame and the rollbar support to the brace . 300 ± 30 in-lbs (34 ± 3 N-m) 3 One bolt on each side attaching the braces to the machine frame.
PAGE 7
Checking the Tire Pressure Check the front and rear tires for proper inflation. Refer to Checking the Tire Pressure in the Operator's Manual for the recommended inflation pressure. Checking the Side Discharge Chute Remove the packing restraint holding the side discharge chute up and lower the chute into place. Checking the Engine Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Oil Level in the Operator's Manual.
PAGE 8