Form No. 3364-249 Rev C Z Master® G3 Riding Mower with 48in TURBO FORCE® Side Discharge Mower Model No. 74922—Serial No. 310000001 and Up G008971 To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. WARNING CALIFORNIA Proposition 65 Warning The engine exhaust from this product contains chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Safe Operating Practices ....................................... 4 Slope Indicator..................................................... 6 Safety and Instructional Decals ............................. 7 Product Overview ...................................................... 11 Controls ............................................................. 11 Specifications ..................................................... 12 Operation...................................................................
Safety • Use extra care when handling gasoline and other fuels. They are flammable and vapors are explosive. Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER-“personal safety instruction." Failure to comply with the instruction may result in personal injury or death.
• Be aware there is no rollover protection when the roll bar is down. • Check the area to be mowed and never fold the ROPS in areas where there are slopes, drop offs or water. • Lower the rollbar only when absolutely necessary. Do not wear the seat belt with the roll bar folded down. • Check carefully for overhead clearances (i.e. branches, doorways, electrical wires) before driving under any objects and do not contact them. • Be aware of the mower discharge direction and do not point it at anyone.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 68-8340 1-403005 98-5954 103-2076 54-9220 58-6520 1.
109-7929 110-2067 107-2102 110-2068 1. Read the Operator's Manual. 114-4466 109-7232 8 1. Main, 25A 3. Charge, 25A 2. PTO, 10A 4.
115-7445 114-9834 1. Power Take-off (PTO) 4. Continuous variable setting 2. Choke 3. Fast 5. Slow 1. Grease pulleys and spindles 2. Maintenance interval—50 hours 116-1716 1. Fuel 2. Empty 6. Hour meter 7. PTO 3. Half 8. Parking brake 4. Full 5. Battery 116-0090 9. Neutral 10.
Battery Symbols Some or all of these symbols are on your battery 116-0205 1. Explosion hazard 6. Keep bystandersa safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8. Battery acid can cause blindness or severe burns. 9. Flush eyes immediately with water and get medical help fast. 5. Read the Operator's Manual. 10.
Product Overview Use these times for scheduling regular maintenance (Figure 6). Fuel Gauge The fuel gauge is located with the hour meter and the bars light up when the ignition switch is on (Figure 6). The indicator light appears when the fuel level is low (approximately one gallon remaining in the fuel tank). Safety Interlock Indicators There are symbols on the hour meter and the indicate with a black triangle that the interlock component is in the correct position (Figure 6).
Blade Control Switch (PTO) The blade control switch (PTO) is used to engage the electric clutch and drive the mower blades. Pull the switch up to engage the blades and release. To disengage the blades, push the blade control switch (PTO) down or move a motion control lever into the neutral lock position. Ignition Switch This switch is used to start the mower engine and has three positions: Start, Run and Off.
Operation Length: 48 inch Deck 52 inch Deck Roll Bar - Up 79.2 inches (201.2 cm) 79.2 inches (201.2 cm) Roll Bar - Down 80.9 inches (205.5 cm) 80.9 inches (205.5 cm) 60 inch Deck 72 inch Deck Roll Bar - Up 83.1 inches (211.1 cm) 86.1 inches (218.7 cm) Roll Bar - Down 84.8 inches (215.4 cm) 87.8 inches (223.0 cm) Note: Determine the left and right sides of the machine from the normal operating position.
Note: A fuel stabilizer/conditioner is most effective when mixed with fresh gasoline. To minimize the chance of varnish deposits in the fuel system, use fuel stabilizer at all times. DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Checking the Engine Oil Level Before you start the engine and use the machine, check the oil level in the engine crankcase; refer to Checking the Engine Oil Level. Breaking In a New Machine New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance.
DANGER CAUTION Operating on wet grass or steep slopes can cause sliding and loss of control. This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. Wheels dropping over edges can cause rollovers, which may result in serious injury, death or drowning. Wear hearing protection when operating this machine. There is no rollover protection when the roll bar is down.
1 Disengaging the Blade Control Switch (PTO) 2 3 G009174 Figure 14 Operating the Throttle G008944 Figure 12 The throttle control can be moved between Fast and Slow positions (Figure 15). Always use the fast position when turning on the mower deck with the blade control switch (PTO). Operating the Mower Blade Control Switch (PTO) The blade control switch (PTO) starts and stops the mower blades and any powered attachments.
Close the fuel shut-off valve for transport, maintenance, and storage. Ensure the fuel shut-off valve is open when starting the engine. 1 1 2 2 G008959 G008948 Figure 16 1. On Figure 18 2. Off 1. On Operating the Ignition Switch 2. Off Starting and Stopping the Engine 1. Turn the ignition key to the Start position (Figure 17). When the engines starts, release the key. Important: Do not engage starter for more than 5 seconds at a time.
Stopping the Engine CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. Let the engine idle at slow throttle (turtle) for 60 seconds before turning the ignition switch off. Figure 19 6. Turn the ignition key to the Start position (Figure 17). When the engines starts, release the key.
The Safety Interlock System operate as described below, have an Authorized Service Dealer repair the safety system immediately. CAUTION 1. Sitting on the seat, engage the parking brake and move the blade control switch (PTO) to on. Try starting the engine; the engine should not crank. If safety interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. 2. Sitting on the seat, engage the parking brake and move the blade control switch (PTO) to off.
Using the Motion Control Levers G008952 Figure 24 Figure 23 Driving Backward 1. Motion control lever-neutral lock position 4. Backward 1. Move the levers to the center, unlocked position. 2. Center, unlocked position 5. Front of machine 2. To go backward, slowly pull the motion control levers rearward (Figure 25). 3. Forward Driving Forward Note: The engine will kill if the traction control levers are moved with the parking brake engaged.
Stopping the Machine To stop the machine, move the traction control levers to neutral and move to locked position, disengage the power take off (blade control switch (PTO), and turn the ignition key to off. Set the parking brake when you leave the machine; refer to Setting the Parking Brake in Operation. Remember to remove the key from the ignition switch. CAUTION Children or bystanders may be injured if they move or attempt to operate the tractor while it is unattended.
Adjusting the Height-of-Cut Pin The height-of-cut is adjusted from 1 to 5-1/2 inches (25 to 140 mm) in 1/4 inch (6 mm) increments by relocating the clevis pin into different hole locations. 1. Move the transport lock to the lock position. 2. Push on the deck lift pedal with your foot and raise the mower deck to the transport position (also the 5-1/2 inch (140 mm) cutting height position) (Figure 27). 3. To adjust, rotate the pin 90 degrees and remove the pin from the height-of-cut bracket (Figure 27).
Position A Adjusting the Flow Baffle Cam Locks This is the full rear position. The suggested use for this position is a follows. This procedure is applicable only to machines with the flow baffle locks. Certain models will have nuts and bolts in-place of the flow baffle locks and can be adjusted the same. • Use for short, light grass mowing conditions. • Use in dry conditions. • For smaller grass clippings. The mower discharge flow can be adjusted for different types of mowing conditions.
Unlatching the Seat • Allows increased ground speed in heavy conditions. • This position is similar to the benefits of the Toro SFS mower. Figure 36 1. Seat latch 2. Seat Using the Drive Wheel Release Valves Figure 34 WARNING Positioning the Seat Hands may become entangled in the rotating drive components below the engine deck, which could result in serious injury. The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable.
Transporting Machines Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets or bystanders avoid injury. WARNING Driving on the street or roadway without turn signals, lights, reflective markings, or a slow moving vehicle emblem is dangerous and can lead to accidents causing personal injury.
Loading Machines Use extreme caution when loading units on trailers or trucks. One full width ramp that is wide enough to extend beyond the rear tires is recommended instead of individual ramps for each side of the unit (Figure 39). The lower rear section of the tractor frame extends back between the rear wheels and serves as a stop for tipping backward. Having a full width ramp provides a surface for the frame members to contact if the unit starts to tip backward.
Mowing Direction shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine TORO replacement blade. Alternate mowing direction to keep the grass standing straight.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. After the first 100 hours • Check the wheel hub slotted nut torque. • Check the torque for wheel lug nuts. • Check the park brake adjustment. Before each use or daily • • • • • • • • Check the safety system. Check the engine oil level. Check the seat belt. Check the rollover protection system (ROPS) knobs. Clean the engine screen and the oil cooler.
CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Lubrication Greasing and Lubrication Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: No. 2 general purpose lithium base or molybdenum base grease How to Grease 1.
2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Grease the mower deck idler pulley pivot until grease come out the bottom (Figure 41). 4. Grease the three spindle bearings until grease comes out the lower seals (Figure 41). Figure 43 Lubricate Caster Wheel Hubs Service Interval: Yearly 1. Stop the engine, wait for all moving parts to stop, and remove the key. Engage the parking brake. G009029 Figure 41 5.
Engine Maintenance adhesive to one spacer nut and thread onto the axle with the wrench flats facing outward. Do Not thread spacer nut all of the way onto the end of the axle. Leave approximately 1/8 inch (3 mm) from the outer surface of the spacer nut to the end of the axle inside the nut. WARNING Contact with hot surfaces may cause personal injury. 9. Insert the assembled nut and axle into the wheel on the side of the wheel with the new seal and bearing.
Servicing the Engine Oil Oil Type: Detergent oil (API service SF, SG, SH, SJ, or SL) Oil Capacity: with a filter change, 71 ounces (2.1 L); without a filter change, 61 ounces (1.8 L) Viscosity: See the table below. Figure 45 1. Air cleaner clamps 3. Primary air filter 2. Air cleaner cover 4. Secondary air filter Servicing the Primary Filter 1. Do not clean the paper filter, replace it (Figure 45). 2. Inspect the element for tears, an oily film, or damage to the rubber seal. 3.
Changing the Engine Oil Service Interval: After the first 8 hours Every 100 hours (more often in dirty or dusty conditions) Note: Dispose of the used oil at a recycling center. G008804 1 1. Start the engine and let it run five minutes. This warms the oil so it drains better. 2 2. Park the machine so that the rear is slightly lower than the front to ensure the oil drains completely. 3. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake.
5. Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 49). 1 2 G008804 3 5 1 2 3 4 4 6 5 6 G008796 Figure 49 6. Start the engine and drive to a flat area. Check the oil level again. 3/4 Changing the Engine Oil Filter G008748 Service Interval: Every 200 hours Figure 50 Note: Change the engine oil filter more frequently when operating conditions are extremely dusty or sandy.
Servicing the Spark Plug Service Interval: Every 100 hours Make sure the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug(s) and a gapping tool/feeler gauge to check and adjust the air gap. Install a new spark plug(s) if necessary. Type of Spark Plug: NGK® BPR4ES or equivalent Air Gap: 0.030 inch (0.75 mm) Removing the Spark Plug 1.
Checking the Spark Plug Check Spark Arrester (if equipped) Important: Never clean the spark plug(s). Always replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, or cracks. Service Interval: Every 50 hours If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. WARNING Hot exhaust system components may ignite gasoline vapors even after the engine is stopped.
Fuel System Maintenance Note: It is important to reinstall the fuel line hoses and secure with plastic ties the same as they were originally installed at the factory to keep the fuel line away from components that could cause fuel line damage. Replacing the Fuel Filter Servicing the Fuel Tank Service Interval: Every 500 hours/Yearly (whichever comes first) (more often in dirty or dusty conditions). Do not attempt to drain the fuel tank.
Electrical System Maintenance WARNING Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Servicing the Battery • Always Disconnect the negative (black) battery cable before disconnecting the positive (red) cable. Service Interval: Monthly WARNING • Always Reconnect the positive (red) battery cable before reconnecting the negative (black) cable.
Important: Always keep the battery fully charged (1.265 specific gravity). This is especially important to prevent battery damage when the temperature is below 32°F (0°C). 1. Charge battery for 10 to 15 minutes at 25 to 30 amps or 30 minutes at 10 amps. G008804 2. When the battery is fully charged, unplug the charger from the electrical outlet, then disconnect the charger leads from the battery posts (Figure 57). 2 3.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check the component/circuit for a malfunction or short. Checking the Seat Belt 1. The fuses are located on right hand console next to the seat (Figure 58). Service Interval: Before each use or daily 2. To replace the fuses, pull out on the fuse to remove it. Visually inspect seat belt for wear, cuts, and proper operation of retractor and buckle.
7. If it tracks to the left, loosen the bolts and adjust the right stop plate rearward on the right T-slot until the machine tracks straight (Figure 60). 8. Tighten the stop plate (Figure 60). Figure 60 Left control lever shown Figure 59 1. ROPS knob (locked position) 3. Roll bar in the upright position 2. Pull ROPS knob out and rotate 90 degrees to change roll bar position 4. Roll bar in the folded position 1. Control lever 3. Stop plate 2.
Figure 63 1. 0.1 inch max Figure 61 2. No more than two threads (0.1 inch max) should be showing here. Checking the Wheel Hub Slotted Nut 4. If more than two threads (0.1 inch) are showing remove nut and install washer between hub and nut. Service Interval: After the first 100 hours 5. Torque the slotted nut to 200 ft-lb (271 N-m). Every 500 hours 6. Then tighten nut until the next set of slots line up with the cross hole in shaft. Do not loosen nut to align the slot.
2. Using an air compressor, blow out any debris from under the brake pole and around the brake spacers. Figure 66 3. Check the condition of the wire harness leads, connectors, and terminals. Clean or repair as necessary. Figure 64 1. Spring Washers 3. Dust Cap 2. Lock Nut 4. Verify that 12V is present at the clutch connector when the PTO switch is engaged. 5. Measure the gap between the rotor and armature. If the gap is greater than .
• If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section. • If the gap is sufficient, proceed to the safety check in step F. F. Perform the following safety check: a. Sit on the seat and start the engine. b. Make sure the blades Do Not engage with the PTO switch “off ” and the clutch disengaged. Figure 68 1. Shim If the clutch does not disengage, reinstall the shim and reference the Troubleshooting section. C.
Cooling System Maintenance Cleaning the Engine Screen and Engine Oil Cooler Service Interval: Before each use or daily Remove any build-up of grass, dirt or other debris from the oil cooler (Figure 71). G008804 Figure 72 1. Engine guard 4. Fan housing 2. Engine air intake screen 5. Screw 3. Bolt Figure 71 Check and Clean the Hydraulic Unit Shrouds Before each use remove any build-up of grass, dirt or other debris from the engine screen.
Brake Maintenance Adjusting the Parking Brake Service Interval: After the first 100 hours Every 500 hours DANGER Mechanical or hydraulic jacks may fail to support machine and cause a serious injury. • Use jack stand when supporting machine. • Do not use hydraulic jacks. Check to make sure the brake is adjusted properly. 1. Drive the machine onto a level surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 3.
15. Close the drive wheel release valve. Refer to Using the Drive Wheel Valves in Operation. Belt Maintenance 16. Repeat on the opposite side of the machine. Inspecting the Belts 17. Install the rear tires and torque the lug nuts to 90-95 ft-lb (122-129 N-m). Service Interval: Every 50 hours 18. Remove jack stands. Check the belts for squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn mower belt.
Figure 77 1. Position the belt cover 3. Ensure the tab is under the metal catch 2. Slide belt cover under the side catches Replacing the Hydraulic Pump Drive Belt Figure 76 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease zerk 3. Spring loaded idler pulley 7. Belt guide 1. Disengage the PTO and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 4. Ratchet 10.
Controls System Maintenance Adjusting the Control Handle Position There are two height positions for the control levers; high and low. Remove the bolts to adjust the height for the operator. 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Figure 78 1. Idler pulley 5. Left hand hydraulic pump pulley 2. Clutch pulley 6.
not have to be in the seat because of the jumper wire being used. Run engine at full throttle and release brake. 6. Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic oil up to operating temperature. Note: The motion control lever needs to be in neutral while making any necessary adjustments. 7. Bring the motion control levers into the neutral position.
Adjusting the Motion Control Damper The top damper mounting bolt can be adjusted to obtain a more desired motion control lever resistance. See Figure 82 for mounting options. Figure 83 1. Flanged nut Figure 82 RH Motion Control Shown 1. Torque the lock nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of locknut after torque. 2. Most resistance (firmest feel) 3. Damper 4. Medium resistance (medium feel) 5.
Hydraulic System Maintenance Servicing the Hydraulic System Hydraulic Oil Type: Toro® HYPR-OIL™ 500 hydraulic oil or Mobil® 1 15W-50. 3 H Important: Use oil specified. Other fluids could cause system damage. Each Hydraulic System Oil Capacity: 52 ounces (1.5 l) per side with filter change Checking the Hydraulic Oil Service Interval: Every 50 hours—Check the hydraulic oil level. 1. Position the machine on a level surface. 4 2.
Replacing the Hydraulic Filters and Hydraulic Oil 1 Service Interval: Every 250 hours—Change the hydraulic filters and hydraulic oil when using Mobil® 1 oil. Every 500 hours—Change the hydraulic filters and hydraulic oil when using Toro® HYPR-OIL™ 500 hydraulic oil. To replace the hydraulic oil, the filters need to be removed. Replace both at the same time. Refer to the oil specifications under Servicing the Hydraulic System for the correct oil. 2 1.
Mower Deck Maintenance Leveling the Mower Deck Setting Up the Machine Note: Ensure the mower deck is leveled before matching the height-of-cut (HOC). 1. Position mower on a flat surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. Figure 87 3. Transport lock 1. Deck lift pedal 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 2. Height of cut pin 6.
13. If the deck is too low, tighten the single point adjustment bolt by rotating it clockwise. If the deck is too high, loosen the single point adjustment bolt by rotating it counterclockwise (Figure 91). 3 4 Note: Loosen or tighten the single point adjustment bolt enough to move the height-of-cut plate mounting bolts at least 1/3 the length of the available travel in their slots. This will regain some up and down adjustment on each of the four deck links. 2 1 2 1 G012430 Figure 89 1.
Servicing the Cutting Blades Checking for Bent Blades Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 2.
performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. 1. Hold the blade end using a rag or thickly-padded glove. Figure 95 2. Remove the blade bolt, curved washer, and blade from the spindle shaft (Figure 94). 1. Sharpen at original angle 2. Check the balance of the blade by putting it on a blade balancer (Figure 96).
Installing the Blades Removing the Mower Deck 1. Install the blade onto the spindle shaft (Figure 97). Before servicing or removing the mower deck, the spring loaded deck arms must be locked out. Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. WARNING Deck lift arm assemblies have stored energy. Removing the deck with out releasing the stored energy can cause serious injury or death. 2. Install the spring disk and blade bolt.
Figure 99 1. Right stabilizer Figure 98 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease zerk 3. Spring loaded idler pulley 7. Belt guide 2. Deck strut (right side shown) 3. Remove the rear deck lift attachment shoulder bolt and nut. 4. Remove the front deck lift attachment shoulder bolt and nut. 8. Raise the deck struts and secure them in the up position. Slide the deck out to the right side of the machine. 4. Ratchet 7.
6 2 4 Cleaning 7 Cleaning Under the Mower 3 Service Interval: Before each use or daily 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 1 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 5 g015594 Figure 100 1. Bolt 3. Raise the mower to the transport position. 5. Spring installed 2. Spacer 6. Grass Deflector 3. Locknut 7.
Storage B. Run the engine to distribute conditioned fuel through the fuel system (5 minutes). Cleaning and Storage C. Stop the engine, allow it to cool, and drain the fuel tank; refer to Servicing the Fuel Tank in the Maintenance Section. 1. Disengage the power take off (blade control switch (PTO), set the parking brake, and turn the ignition key to Off. Remove the key. 2. Remove grass clippings, dirt, and grime from the external parts of the entire machine, especially the engine and hydraulic system.
Troubleshooting Problem Starter does not crank Engine will not start, starts hard, or fails to keep running Possible Cause 1. Blade control switch (PTO) is engaged. 1. Move blade control switch (PTO) to disengaged. 2. Parking brake is not on. 3. Drive levers are not in neutral lock position. 4. Operator is not seated. 5. Battery is dead. 6. Electrical connections are corroded or loose. 7. Fuse is blown. 8. Relay or switch is defective. 2. Set the parking brake. 3.
Problem Machine does not drive. Abnormal vibration. Uneven cutting height. Possible Cause 1. By pass valves is not closed tight. 1. Tighten the by pass valves. 2. 3. 4. 5. 2. 3. 4. 5. Pump belt is worn, loose or broken. Pump belt is off a pulley. Broken or missing idler spring. Hydraulic oil level is low or too hot. 1. Install new cutting blade(s). 2. Blade mounting bolt is loose. 3. Engine mounting bolts are loose. 4. Loose engine pulley, idler pulley, or blade pulley. 5. Engine pulley is damaged.
Schematics Wire Diagram (Rev.
Notes: 66
Notes: 67
The Toro Total Coverage Warranty A Limited Warranty (see warranty periods below) Conditions and Products Covered 3. The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship. Warranty Period •Engine •Battery See engine manufacturer's warranty1 90 days Parts and Labor 1 year Parts only •Belts and Tires 90 days •Attachments 1 year 21 in.
