Operator's Manual
Table Of Contents
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- Adding Fuel
- Checking the Engine-oil Level
- Breaking In a New Machine
- Using the Rollover Protection System (ROPS)
- Think Safety First
- Operating the Parking Brake
- Operating the Mower Blade-control Switch (PTO)
- Operating the Throttle
- Operating the Choke
- Operating the Ignition Switch
- Using the Fuel Shutoff Valve
- Starting and Stopping the Engine
- Using the Safety-interlock System
- Driving Forward or Backward
- Stopping the Machine
- Adjusting the Height-of-Cut
- Adjusting the Anti-scalp Rollers
- Adjusting the Flow Baffle Cam Locks
- Positioning the Flow Baffle
- Positioning the Seat
- Unlatching the Seat
- Changing the Seat Suspension
- Using the Drive-wheel-release Valves
- Using the Side Discharge
- Transporting Machines
- Loading Machines
- Adding Light Oil or Spray Lubrication
- Greasing the Mower
- Lubricating the Caster-wheel Hubs
- Servicing the Air Cleaner
- Servicing the Engine Oil
- Servicing the Spark Plug
- Checking the Spark Arrester (if equipped)
- Replacing the Fuel Filter
- Servicing the Fuel Tank
- Servicing the Battery
- Servicing the Fuses
- Checking the Seat Belt
- Checking the Rollover Protection System (ROPS) Knobs
- Adjusting the Tracking
- Checking the Tire Pressure
- Checking the Wheel Lug Nuts
- Checking the Wheel Hub Slotted Nut
- Adjusting the Caster-pivot Bearing
- Using the Clutch Shim
- Cleaning the Engine Screen and Engine-oil Cooler
- Cleaning the Engine-cooling Fins and Shrouds
- Checking and Cleaning the Hydraulic-unit Shrouds
- Adjusting the Parking Brake
- Inspecting the Belts
- Replacing the Mower Belt
- Replacing the Hydraulic Pump-drive Belt
- Adjusting the Control-handle Position
- Adjusting the Motion-control Linkage
- Adjusting the Motion-control Damper
- Adjusting the Motion Control Neutral-lock Pivot
- Servicing the Hydraulic System
- Mower Deck Maintenance
- Cleaning under the Mower
- Disposing of Waste
- NO TITLE
AdjustingtheHeight-of-CutPin
Theheight-of-cutisadjustedfrom25to140mm(1to
5-1/2inches)in6mm(1/4inch)incrementsbyrelocating
theclevispinintodifferentholelocations.
1.Movethetransportlocktothelockposition.
2.Pushonthedeck-liftpedalwithyourfoot,andraisethe
mowerdecktothetransportposition(alsothe140mm
(5-1/2inches)cuttingheightposition)asshownin
Figure27.
3.Toadjust,rotatethepin90degreesandremovethepin
fromtheheight-of-cutbracket(Figure27).
4.Selectaholeintheheight-of-cutbracketcorresponding
totheheight-of-cutdesired,andinsertthepin(
Figure
27).
5.Pushonthedecklift,pullbackonthetransportlock,
andslowlylowerthemowerdeck.
1
3
2
G017027
Figure27
1.Deck-liftpedal
3.Transportlock
2.Cut-of-heightpin
AdjustingtheAnti-scalp
Rollers
Wheneveryouchangetheheight-of-cut,itisrecommended
toadjusttheheightoftheanti-scalprollers.
1.Disengagetheblade-controlswitch(PTO),movethe
motion-controlleverstotheneutral-lockedposition,
andsettheparkingbrake.
2.Stoptheengine,removethekey,andwaitforallmoving
partstostopbeforeleavingtheoperatingposition.
3.Adjusttheanti-scalprollersasshownin
,,and.
Figure28
1.Anti-scalproller4.Flangenut
2.Spacer
5.Bolt
3.Bushing
Figure29
1.Anti-scalproller3.Flangenut
2.Bushing4.Bolt
Figure30
1.Anti-scalproller4.Flangenut
2.Spacer
5.Bolt
3.Bushing
25