Operator's Manual
Table Of Contents
- NO TITLE
- NO TITLE
- NO TITLE
- NO TITLE
- Adding Fuel
- Checking the Engine-oil Level
- Breaking In a New Machine
- Using the Rollover Protection System (ROPS)
- Think Safety First
- Operating the Parking Brake
- Operating the Mower Blade-control Switch (PTO)
- Operating the Throttle
- Operating the Choke
- Operating the Ignition Switch
- Using the Fuel Shutoff Valve
- Starting and Stopping the Engine
- Using the Safety-interlock System
- Driving Forward or Backward
- Stopping the Machine
- Adjusting the Height-of-Cut
- Adjusting the Anti-scalp Rollers
- Adjusting the Flow Baffle Cam Locks
- Positioning the Flow Baffle
- Positioning the Seat
- Unlatching the Seat
- Changing the Seat Suspension
- Using the Drive-wheel-release Valves
- Using the Side Discharge
- Transporting Machines
- Loading Machines
- Adding Light Oil or Spray Lubrication
- Greasing the Mower
- Lubricating the Caster-wheel Hubs
- Servicing the Air Cleaner
- Servicing the Engine Oil
- Servicing the Spark Plug
- Checking the Spark Arrester (if equipped)
- Replacing the Fuel Filter
- Servicing the Fuel Tank
- Servicing the Battery
- Servicing the Fuses
- Checking the Seat Belt
- Checking the Rollover Protection System (ROPS) Knobs
- Adjusting the Tracking
- Checking the Tire Pressure
- Checking the Wheel Lug Nuts
- Checking the Wheel Hub Slotted Nut
- Adjusting the Caster-pivot Bearing
- Using the Clutch Shim
- Cleaning the Engine Screen and Engine-oil Cooler
- Cleaning the Engine-cooling Fins and Shrouds
- Checking and Cleaning the Hydraulic-unit Shrouds
- Adjusting the Parking Brake
- Inspecting the Belts
- Replacing the Mower Belt
- Replacing the Hydraulic Pump-drive Belt
- Adjusting the Control-handle Position
- Adjusting the Motion-control Linkage
- Adjusting the Motion-control Damper
- Adjusting the Motion Control Neutral-lock Pivot
- Servicing the Hydraulic System
- Mower Deck Maintenance
- Cleaning under the Mower
- Disposing of Waste
- NO TITLE
MowerDeck
Maintenance
LevelingtheMowerDeck
SettinguptheMachine
Note:Ensurethatthemowerdeckisleveledbefore
matchingtheheight-of-cut(HOC).
1.Positionthemoweronaatsurface.
2.Disengagetheblade-controlswitch(PTO),movethe
motion-controlleverstotheneutral-lockedposition,
andsettheparkingbrake.
3.Stoptheengine,removethekey,andwaitforallmoving
partstostopbeforeleavingtheoperatingposition.
4.Checktirepressureofthedrivetires.
5.Ifneeded,adjustto90kPa(13psi).
6.Positionthemowertothe76mm(3inches)
height-of-cutposition.
LevelingtheDeck
1.Positionthemoweronaatsurface.
2.Stopengine,waitforallmovingpartstostop,remove
thekey,andengagetheparkingbrake.
3.Checkthetirepressureinthedrivetires.
Note:Properinationpressureforthetiresis90kPa
(13psi).
4.Positionthetransportlockinthelatchingposition.
5.Pushthedeck-liftpedalallthewayforwardandthe
deckwilllatchatthe14cm(5-1/2inches)transport
position(
Figure87).
1
3
2
G017027
Figure87
1.Deck-liftpedal
3.Transportlock
2.Height-of-cutpin
6.Inserttheheightadjustmentpinintothe7.6cm(3
inches)cuttingheightlocation.
7.Releasethetransportlockandallowthedecktolower
tothecuttingheight.
8.Raisethedischargechute.
9.Onbothsidesofthedeck,measurefromthelevel
surfacetothefronttipoftheblade(PostionA)as
showninFigure88.
Note:Themeasurementshouldread7.6mm(3
inches)
Figure88
1.7.6cm(3inches)at
positionAiscorrect
3.Measureherefromthe
bladetiptothehard
surface
2.8.3cm(3-1/4inches)at
positionBiscorrect
4.MeasureatpositionAand
Bonbothsides
57