Form No. 3394-324 Rev B Z Master® Commercial 3000 Series Riding Mower with 52in or 72in TURBO FORCE® Side Discharge Mower Model No. 74955—Serial No. 315000001 and Up Model No. 74959—Serial No. 315000001 and Up Register at www.Toro.com.
This spark ignition system complies with Canadian ICES-002 Introduction Because in some areas there are local, state, or federal regulations requiring that a spark arrester be used on the engine of this machine, a spark arrester is available as an option. If you require a spark arrestor, contact your Authorized Toro Dealer. This rotary-blade, riding lawn mower is intended to be used by residential homeowners or professional, hired operators.
Servicing the Engine Oil.................................... 37 Servicing the Spark Plug................................... 40 Check the Spark Arrester (if equipped).............. 41 Fuel System Maintenance ................................... 42 Replacing the Fuel Filter ................................... 42 Servicing the Fuel Tank..................................... 42 Electrical System Maintenance ........................... 43 Servicing the Battery.........................................
Safety properly. Do not operate unless they are functioning properly. Improper use or maintenance can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER-“personal safety instruction." Failure to comply with the instruction may result in personal injury or death. Operation • Lightning can cause severe injury or death.
Maintenance and Storage Rollover Protection System (ROPS) - Use and Maintenance • Disengage drives, set parking brake, stop engine and remove key or disconnect spark-plug wire. Wait for all movement to stop before adjusting, cleaning or repairing. • Do not remove the ROPS. • The ROPS is an integral and effective safety device. Keep the ROPS on the machine and use the seat belt when operating the machine. • Clean grass and debris from cutting unit, drives, mufflers, and engine to help prevent fires.
Slope Indicator g011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. decal58-6520 58-6520 decal106-2655 1. Grease 106-2655 1. Warning-do not touch or approach moving belts; remove the ignition key and read the instructions before servicing or performing maintenance. decal93-7818 93-7818 1.
decal110-2068 110-2068 1. Read the Operator's Manual. decal112-9028 112-9028 1. Warning—stay away from moving parts; keep all guards in place. decal107-3069 107-3069 1. Warning–there is no rollover protection when the roll bar is down. 2. To avoid injury or death from a rollover accident, keep the roll bar in the raised and locked position and wear the seat belt. Lower the roll bar only when absolutely necessary; do not wear the seat belt when the roll bar is down. 3.
decal116-1716 116-1716 1. Fuel 2. Empty 6. Hour meter 7. PTO 3. Half 8. Parking brake 4. Full 5. Battery 9. Neutral 10. Operator presence switch decal117-0346 117-0346 1. Fuel leak hazard—read the Operator's Manual; do not attempt to remove the roll bar; do not weld, drill or modify the roll bar in any way. decal116-4858 116-4858 decal116-5988 decal117-3848 116-5988 1. Parking brake—engaged 117-3848 2. Parking brake—disengaged 1.
decal126-2055 126-2055 1. Wheel lug nut torque 95 ft-lb (129 N-m) (4x) 2. Wheel hub nut torque 235 ft-lb (319 N-m) 3. Read and understand the Operator’s Manual before performing any maintenance, check torque after first 100 hours then every 500 hours thereafter. decal117-3864 117-3864 1. Read the Operator’s Manual. 2. Fill to bottom of filler neck; warning—do not overfill the tank. decal126-4398 126-4398 1. Read the Operator’s Manual 2. Lock decal121-7551 121-7551 1. Power Take-off (PTO) 4.
decaloemmarkt Manufacturer's Mark 1. Indicates the blade is identified as a part from the original machine manufacturer. decal127-0326 127-0326 1. Read the Operator's Manual. 3. Remove the key from the ignition and read the Operator's Manual before performing maintenance or servicing the machine. 2. Height-of-cut decal131-4036 131-4036 1. Maximum drawbar pull 36 kg (80 lb) 2. Read the Operator's Manual. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery 1.
decal116-8722 116-8722 1. Warning-Read the Operator’s Manual. Do not operate this machine unless you are trained. Wear hearing protection. 4. Cutting/dismemberment of hand or foot-stay away from moving parts; keep all guards and shields in place. 2. Warning-Stay away from moving parts; keep all guards in place. Stop engine and remove key before adjusting, servicing, or cleaning. 5. Thrown object hazard-Pick up objects that could be thrown by mower. Do not operate when people and pets are in the area.
decal127-0335 127–0335 1. Tipping hazard on slopes—do not make sudden, tight turns; 2. Ramp hazard—when loading onto a trailer, do not use dual make slow, wide turns; do not use on slopes near open water; ramps; only use a singular ramp wide enough for the machine do not use this machine on slopes greater than 15 degrees. and that has an incline less than 15 degrees; back up the ramp (in reverse) and drive forward off the ramp.
decal132-0871 132-0871 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in those conditions on that day and at that site.
Hour Meter Product Overview The hour meter records the number of hours the engine has operated. It operates when the engine is running. Use these times for scheduling regular maintenance (Figure 6). Fuel Gauge The fuel gauge is located with the hour meter and the bars light up when the ignition switch is on (Figure 6). The indicator light appears when the fuel level is low (approximately one gallon remaining in the fuel tank).
Specifications the switch up to engage the blades and release. To disengage the blades, push the blade-control switch (PTO) down or move a motion-control lever into the neutral lock position. Note: Specifications and design are subject to change without notice. Width: Ignition Switch This switch is used to start the mower engine and has 3 positions: Start, Run, and Off.
Operation DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Add the correct amount of gas stabilizer/conditioner to the gas. WARNING There is no rollover protection when the roll bar is in the down position. Note: A fuel stabilizer/conditioner is most effective when mixed with fresh gasoline. To minimize the chance of varnish deposits in the fuel system, use fuel stabilizer at all times. • Lower the roll bar only when absolutely necessary. • Do not wear the seat belt when the roll bar is in the down position. Filling the Fuel Tank 1.
DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges can cause rollovers, which may result in serious injury, death or drowning. There is no rollover protection when the roll bar is down. Always keep the roll bar in the fully raised and locked position and use the seat belt. Read and follow the rollover protection instructions and warnings. To avoid loss of control and possibility of rollover: • Do not operate near drop-offs or near water.
Releasing the Parking Brake CAUTION This machine produces sound levels in excess of 85 dBA at the operators ear and can cause hearing loss through extended periods of exposure. Wear hearing protection when operating this machine. The use of protective equipment for eyes, ears, feet, and head is recommended. g027335 Figure 11 Operating the Mower Blade-Control Switch (PTO) g009027 Figure 9 1.
Operating the Throttle Using the Fuel Shutoff Valve The throttle control can be moved between the Fast and Slow positions (Figure 14). The fuel shutoff valve is located under the seat. Move the seat forward to access it. Always use the fast position when turning on the mower deck with the blade-control switch (PTO). Close the fuel shutoff valve for transport, maintenance, and storage. Ensure the fuel shutoff valve is open when starting the engine. g008946 Figure 14 Operating the Ignition Switch 1.
Stopping the Engine CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. Let the engine idle at slow throttle (turtle) for 60 seconds before turning the ignition switch off. g027336 Figure 17 6. Turn the ignition key to the Start position (Figure 15). When the engines starts, release the key.
The Safety-Interlock System Test the safety-interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately. CAUTION If safety-interlock switches are disconnected or damaged the machine could operate unexpectedly causing personal injury. 1. Sitting on the seat, engage the parking brake and move the blade-control switch (PTO) to on. Try starting the engine; the engine should not crank.
Using the Motion-Control Levers g008952 Figure 22 g004532 Driving Backward Figure 21 1. Motion-control lever—neutral lock position 4. Backward 2. Center, unlocked position 5. Front of machine 1. Move the levers to the center, unlocked position. 2. To go backward, slowly pull the motion control levers rearward (Figure 23). 3. Forward Driving Forward Note: The engine will kill if the traction control levers are moved with the parking brake engaged.
Stopping the Machine To stop the machine, move the traction control levers to neutral and move to locked position, disengage the power take off (blade control switch (PTO), and turn the ignition key to the off position. Set the parking brake when you leave the machine; refer to Setting the Parking Brake (page 20). Remove the key from the ignition switch. CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended.
Adjusting the Height-of-Cut Pin The height-of-cut is adjusted from 25 to 140 mm (1 to 5-1/2 inches) in 6 mm (1/4 inch) increments by relocating the clevis pin into different hole locations. g008955 Figure 24 Transport Lock Positions 1. Transport lock 3. Unlock position—does not lock the mower deck into transport position 2. Lock position—mower deck will lock into transport position 26 1. Move the transport lock to the lock position. 2.
g000942 Figure 26 1. Anti-scalp roller 4. Flange nut 2. Spacer 5. Bolt 3. Bushing g027343 Figure 25 1. Deck-lift pedal 3. Transport lock 2. Cut of height pin Adjusting the Anti-scalp Rollers Whenever you change the height-of-cut, it is recommended to adjust the height of the anti-scalp rollers. 1. g000943 Figure 27 Disengage the blade-control switch (PTO), move the motion-control levers to the neutral-locked position, and set the parking brake. 2.
Adjusting the Flow Baffle Cam Locks Positioning the Flow Baffle The following figures are only recommendations for use. Adjustments will vary by grass type, moisture content, and height of grass. This procedure is applicable only to machines with the flow baffle locks. Certain models will have nuts and bolts in-place of the flow baffle locks and can be adjusted the same. Note: If the engine power draws down and the mower ground speed is the same, open up the baffle.
Using the Drive-Wheel-Release Valves Position C This is the full open position. The suggested use for this position is as follows. • Use in tall, dense grass mowing conditions. • Use in wet conditions. WARNING • Lowers the engine power consumption. Hands may become entangled in the rotating drive components below the engine deck, which could result in serious injury. • Allows increased ground speed in heavy conditions.
necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets or bystanders avoid injury. WARNING Driving on the street or roadway without turn signals, lights, reflective markings, or a slow moving vehicle emblem is dangerous and can lead to accidents causing personal injury. Do not drive machine on a public street or roadway. g015123 To transport the machine: Figure 34 1.
g028043 Figure 36 1. Back up ramps 2. Drive forward down ramps Important: Do not use narrow individual ramps for each side of the machine. Ensure the ramp is long enough so that the angle with the ground does not exceed 15 degrees (Figure 37). On flat ground, this requires a ramp to be at least four times (4X) as long as the height of the trailer or truck bed to the ground. A steeper angle may cause mower components to get caught as the unit moves from the ramp to the trailer or truck.
Cutting Long Grass Operating Tips If the grass is ever allowed to grow slightly longer than normal, or if it contains a high degree of moisture, raise the cutting height higher than usual and cut the grass at this setting. Then cut the grass again using the lower, normal setting. Maximizing Cutting Efficiency For best mowing and maximum air circulation, operate the engine at the fast throttle position.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 8 hours • Change the engine oil. After the first 100 hours • Check the wheel lug nut torque. • Check the wheel hub slotted-nut torque. • Check the parking brake adjustment. After the first 250 hours • Change the hydraulic filters and hydraulic oil when using any type of oil. Before each use or daily • • • • • • • • Check the safety system. Check the engine-oil level.
CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Lubrication Greasing the Mower Grease more frequently when operating conditions are extremely dusty or sandy. Service Interval: Every 50 hours—Grease the mower deck spindles and idler arm. Yearly—Grease the pump belt idler arm. Grease Type: No.
Lubricate the Caster-Wheel Hubs Service Interval: Yearly 1. Stop the engine, wait for all moving parts to stop, and remove the key. Engage the parking brake. g009030 Figure 40 g006115 Figure 42 6. Remove the dust cap and adjust the caster pivots. 1. Seal guard Note: Keep the dust cap off until greasing is complete. Refer to Adjusting the Caster-Pivot Bearing (page 46). 2. Raise the front of the machine up and support it with jack stands. 7.
Engine Maintenance 11. With the open end of the wheel facing up, fill the area inside the wheel around the axle full of general-purpose grease. 12. Insert the second bearing and new seal into the wheel. 13. Apply a thread locking adhesive to the second spacer nut and thread it onto the axle with the wrench flats facing outward. Every 300 hours/Yearly (whichever comes first)—Replace the primary air filter (more often in dusty or sandy conditions). 14.
Servicing the Safety Filter Note: Avoid knocking the filter into the side of the body. 9. Replace the safety filter, never clean it. Remove the inner filter only if you intend to replace it. Important: Never attempt to clean the inner Important: Do not attempt to clean the safety filter. If the safety filter is dirty, then the primary filter is damaged. Replace both filters. filter. If the safety filter is dirty, then the primary filter is damaged. Replace both filters.
Checking the Engine-Oil Level Service Interval: Before each use or daily Note: Check the oil when the engine is cold. WARNING g008804 Contact with hot surfaces may cause personal injury. Keep hands, feet, face, clothing, and other body parts away from the muffler and other hot surfaces. Important: Do not overfill the crankcase with oil because damage to the engine may result. Do not run engine with oil below the Low mark because the engine may be damaged. 1.
Changing the Engine Oil 5. Service Interval: After the first 8 hours Every 100 hours (more often in dirty or dusty conditions). Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 48). Note: Dispose of the used oil at a recycling center. 1. Start the engine and let it run for 5 minutes. Note: This warms the oil so it drains better. 2. 3. 4.
Removing the Spark Plug 1. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 2. Disengage the PTO, move the motion-control levers to the neutral locked position and set the parking brake. 3. Remove the left hydraulic unit shroud in the order listed with Figure 50. This gives you access to the front spark plug. g008804 g009922 g027477 Figure 49 Note: Ensure the oil-filter gasket touches the engine, and then an extra 3/4 turn is completed.
Installing the Spark Plug Tighten the spark plug(s) to 24.4–29.8 N-m (18-22 ft.-lb). g008803 g027478 Figure 51 5. Install the left hydraulic unit shroud (Figure 50). g027735 Figure 53 Checking the Spark Plug Important: Replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, cracks or reuse is questionable. Check the Spark Arrester (if equipped) If you see light brown or gray on the insulator, the engine is operating properly.
Fuel System Maintenance originally installed at the factory to keep the fuel line away from components that can cause fuel line damage. Replacing the Fuel Filter Servicing the Fuel Tank Service Interval: Every 500 hours/Yearly (whichever comes first) (more often in dirty or dusty conditions). Do not attempt to drain the fuel tank. Ensure that an Authorized Service Dealer drains the fuel tank and services any components of the fuel system.
Electrical System Maintenance 3. First disconnect the negative battery cable (black) from the negative (-)(black) battery terminal (Figure 55). 4. Slide the red terminal boot off the positive (red) battery terminal and remove the positive (+)(red) battery cable (Figure 55). 5. Remove the wing nut securing the battery clamp (Figure 55). 6. Remove the clamp (Figure 55). 7. Remove the battery.
Charging the Battery 3. Install a new fuse (Figure 57). WARNING Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from battery. Important: Always keep the battery fully charged (1.265 specific gravity). This is especially important to prevent battery damage when the temperature is below 32°F (0°C). 1. Charge battery for 10 to 15 minutes at 25 to 30 amps or 30 minutes at 10 amps. 2.
Drive System Maintenance Checking the Seat Belt Service Interval: Before each use or daily Visually inspect seat belt for wear, cuts, and proper operation of retractor and buckle. Replace before operating if damaged. Checking the Rollover Protection System (ROPS) Knobs Service Interval: Before each use or daily WARNING To avoid injury or death from rollover: keep the roll bar in the fully raised locked position and use the seat belt. Ensure the seat is secured to the machine.
8. Checking the Wheel Lug Nuts Tighten the stop plate (Figure 59). Check and torque the wheel lug nuts to 122-129 N-m (90-95 ft-lb). Checking the Wheel Hub Slotted Nut Service Interval: After the first 100 hours Every 500 hours Check and ensure that the torque of the slotted nut is 286 to 352 N-m (211 to 260 ft-lb). Note: Do not use anti-seize on wheel hub. g010153 Figure 59 Left control lever shown 1. Control lever 3. Stop plate 2.
3. Remove the dust cap from caster and tighten locknut (Figure 62). 4. Tighten the locknut until the spring washers are flat and then back off a 1/4 turn to properly set the pre-load on the bearings (Figure 62). Important: Make sure the spring washers are installed correctly as shown in Figure 62. 5. Install the dust cap (Figure 62). g010869 Figure 63 1. Armature 5. Brake spacer 2. Field shell 6. Re-gap shim 3. Rotor 7. Brake pole 4. Brake mounting bolt Removing the Clutch Shim 1.
Note: Do not remove the brake pole from the field shell/armature. The brake pole has worn to match the armature and needs to continue to match after the shim is removed to ensure proper brake torque. g010872 Figure 67 1. Feeler gauge g010870 Figure 65 1. Brake mounting bolt B. Using needle nose pliers, or by hand, take hold of the tab, and remove the shim (Do not discard the shim until proper clutch function has been confirmed). g010873 Figure 68 1. Feeler gauge • If the gap is less than 0.
Cooling System Maintenance Cleaning the Engine Screen and Engine-Oil Cooler Service Interval: Before each use or daily Remove any build-up of grass, dirt, or other debris from the oil cooler (Figure 69). g008804 g004218 Figure 70 1. Engine guard 4. Fan housing 2. Engine air-intake screen 5. Screw 3. Bolt g009191 Figure 69 Before each use remove any build-up of grass, dirt, or other debris from the engine screen.
Brake Maintenance Check and Clean the Hydraulic Units Adjusting the Parking Brake Service Interval: Before each use or daily 1. Disengage the PTO and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Service Interval: After the first 100 hours 3. Move the seat forward. 4. Clean the debris and grass from the hydraulic units (Figure 71). Check to make sure the brake is adjusted properly before adjusting. 5.
Belt Maintenance Inspecting the Belts Service Interval: Every 50 hours Check the belts for squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks, and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. Replacing the Mower Belt g026961 Figure 72 Left Side Shown 1. L-bracket 4. Rear linkage assembly 2. Linkage stop 5. Caliper 3. Gap 6.
g027730 Figure 75 1. Position the belt cover 3. Ensure the tab is under the metal catch 2. Slide belt cover under the side catches g009038 Replacing the Hydraulic Pump-Drive Belt Figure 74 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease fitting 3. Spring loaded idler pulley 7. Belt guide 4. Ratchet 1. Disengage the PTO and set the parking brake. 2.
Controls System Maintenance Adjusting the Control-Handle Position There are 2 height positions for the control levers; high and low. Remove the bolts to adjust the height for the operator. 1. Disengage the PTO, move the motion-control levers to the neutral locked position, and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Loosen the bolts and flange nuts installed in the levers (Figure 77). 4.
5. Start the engine. Note: The brake must be engaged and the motion-control levers must be out to start the engine. The operator does not have to be in the seat because of the jumper wire being used. Run the engine at full throttle and release the brake. 6. Run the machine at least 5 minutes with the motion-control levers at full forward speed to bring the hydraulic oil up to operating temperature. Note: The motion-control lever needs to be in neutral while making any necessary adjustments.
10. For less resistance, loosen the flanged nut Shut off the machine. Remove the jumper wire from wire harness and plug the connector into the seat switch. 11. Remove the jack stands. 12. Raise the deck and install the height-of-cut pin. 13. Check that the machine does not creep in neutral with the park brakes disengaged. 3. Tighten the jam nut.
Hydraulic System Maintenance Servicing the Hydraulic System Hydraulic Oil Type: Toro® HYPR-OIL™ 500 hydraulic oil or Mobil® 1 15W-50. Important: Use oil specified. Other fluids could cause system damage. Each Hydraulic System Oil Capacity: 52 ounces (1.5 l) per side with filter change Checking the Hydraulic Oil Service Interval: Every 50 hours—Check the hydraulic oil level. 1. Position the machine on a level surface. 2.
Replacing the Hydraulic Filters and Hydraulic Oil Service Interval: After the first 250 hours—Change the hydraulic filters and hydraulic oil when using any type of oil. Every 250 hours—Change the hydraulic filters and hydraulic oil when using Mobil® 1 oil (more often in dirty or dusty conditions). Every 500 hours—Change the hydraulic filters and hydraulic oil when using Toro® HYPR-OIL™ 500 hydraulic oil (more often in dirty or dusty conditions). To replace the hydraulic oil, the filters need to be removed.
Mower Deck Maintenance Leveling the Mower Deck Setting Up the Machine Note: Ensure the mower deck is leveled before matching the height-of-cut (HOC). 1. Position mower on a flat surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 4. Check tire pressure of the tires.
10. the deck is too high, loosen the single point adjustment bolt by rotating it counterclockwise (Figure 89). If needed, loosen the whizlock nut on the side of the yoke and the jam nut on top. Fine tune the screw adjuster by turning it to get 7.6 mm (3 inch) height (see Figure 87). Note: Loosen or tighten the single point adjustment bolt enough to move the height-of-cut plate mounting bolts at least 1/3 the length of the available travel in their slots.
Checking for Bent Blades turns grass brown at the edges, which slows growth and increases the chance of disease. Check the cutter blades daily for sharpness, and for any wear or damage. File down any nicks and sharpen the blades as necessary. If a blade is damaged or worn, replace it immediately with a genuine Toro replacement blade. For convenient sharpening and replacement, you may want to keep extra blades on hand. 1.
Removing the Blades 2. Blades must be replaced if a solid object is hit, if the blade is out of balance or is bent. To ensure optimum performance and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. 1. 2. Check the balance of the blade by putting it on a blade balancer (Figure 94). Note: If the blade stays in a horizontal position, the blade is balanced and can be used.
Removing the Mower Deck Lock out the spring loaded deck arms before servicing or removing the mower deck. WARNING Deck-lift arm assemblies have stored energy. Removing the deck with out releasing the stored energy can cause serious injury or death. Do not attempt to disassemble the deck from the front frame without locking out the stored energy. 1. Stop the engine, wait for all of the moving parts to stop, remove the key, and engage parking brake. 2.
8. 9. Important: The grass deflector must be able Raise the deck struts and secure them in the up position. to rotate. Lift the deflector up to the full open position and ensure that it rotates into the full down position. Slide the deck out to the right side of the machine. Replacing the Grass Deflector WARNING An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or bystander's direction and result in serious injury. Also, contact with the blade could occur.
Cleaning Storage Cleaning Under the Mower Cleaning and Storage Service Interval: Before each use or daily 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position, and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Raise the mower to the transport position. 1.
B. Run the engine to distribute conditioned fuel through the fuel system (5 minutes). C. Stop the engine, allow it to cool, and drain the fuel tank; refer to Servicing the Fuel Tank (page 42) in the Maintenance Section. D. Restart the engine and run it until it stops. E. Dispose of fuel properly. Recycle as per local codes. Important: Do not store stabilizer/conditioned fuel over 90 days. 13. Check and tighten all bolts, nuts, and screws. Repair or replace any part that is damaged. 14.
Troubleshooting Problem The starter does not crank. The engine will not start, starts hard, or fails to keep running Possible Cause 1. The blade control switch (PTO) is engaged. 1. Move the blade control switch (PTO) to disengaged. 2. The parking brake is not on. 3. The drive levers are not in neutral lock position. 4. The operator is not seated. 5. The battery is dead. 6. The electrical connections are corroded or loose. 7. The fuse is blown. 8. The relay or switch is defective. 2.
Problem The machine does not drive. There is abnormal vibration. Mowing is resulting in uneven cutting height. Possible Cause 1. The by pass valves is not closed tight. 1. Tighten the by pass valves. 2. 3. 4. 5. 2. 3. 4. 5. The pump belt is worn, loose or broken. The pump belt is off a pulley. The idler sprint is broken or missing. The hydraulic oil level is low or too hot. 1. Install new cutting blade(s). 2. The blade mounting bolt is loose. 3. The engine mounting bolts are loose. 4.
Schematics g020788 Electrical Schematic (Rev.
Notes:
Notes:
Notes:
The Toro Total Coverage Warranty Landscape Contractor Equipment (LCE) A Limited Warranty (see warranty periods below) Conditions and Products Covered Instructions for Obtaining Warranty Service The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship.