Form No. 3424-590 Rev B Z Master® Commercial 3000 Series Riding Mower with 60in TURBO FORCE® Side Discharge Mower Model No. 74958—Serial No. 403319861 and Up Register at www.Toro.com.
Introduction It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire. This rotary-blade, riding lawn mower is intended to be used by professional, hired operators.
Contents (Figure 2), which signals a hazard that may cause serious injury or death if you do not follow the recommended precautions. Safety ....................................................................... 4 General Safety ................................................... 4 Slope Indicator ................................................... 5 Safety and Instructional Decals .......................... 6 Product Overview ................................................... 12 Controls ...............
Safety Servicing the Electronic Fuel-Injection System.......................................................... 42 Replacing the Low-Pressure Fuel Filter.............................................................. 42 Servicing the High-Pressure Fuel Filter............. 42 Servicing the Fuel Tank..................................... 42 Electrical System Maintenance ........................... 43 Electrical System Safety ................................... 43 Servicing the Battery..........................
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal93-7818 93-7818 decalbatterysymbols 1. Warning—read the Operator's Manual for instructions on torquing the blade bolt/nut to 115 to 149 N∙m (85 to 110 ft-lb). Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance away from the battery. 2.
decal106-5517 106-5517 1. Warning—do not touch the hot surface. decal110-2068 110-2068 1. Read the Operator's Manual. decal112-9028 112-9028 1. Warning—stay away from moving parts; keep all guards and shields in place. decal114-4466 114-4466 1. Main (25 A) 3. Charge (25 A) 2. PTO (10 A) 4. Auxiliary (15 A) decal107-3069 107-3069 1. Warning–there is no rollover protection when the roll bar is down. 2.
decal133-8062 133-8062 decal116-5988 116-5988 1. Parking brake—engaged 2. Parking brake—disengaged decal117-0346 117-0346 1. Fuel leak hazard—read the Operator's Manual; do not attempt to remove the roll bar; do not weld, drill, or modify the roll bar in any way. decal116-8726 116-8726 1. Read the Operator’s Manual for the recommended hydraulic fluid. decal117-3848 117-3848 1. Thrown object hazard—keep bystanders a safe distance away from the machine. 2.
decal119-6807 119-6807 1. Warning—no step decal126-4398 126-4398 decal121-7586 121-7586 1. Fast 2. Variable-speed control 1. Read the Operator’s Manual. 2. Lock 3. Slow 4. Power takeoff (PTO) 3. Unlock decal126-2055 126-2055 1. Wheel lug nut torque 95 ft-lb (129 N∙m) (4x) 2. Wheel hub nut torque 235 ft-lb (319 N∙m) 3. Read and understand the Operator’s Manual before performing any maintenance, check torque after first 100 hours then every 500 hours thereafter. decal127-0326 127-0326 1.
decal136-5508 136-5508 1. Belt routing decal125-9383 125-9383 1. Check the hydraulic fluid every 50 operating hours. 3. Check the tire pressure every 50 operating hours. 2. Read the Operator’s Manual for information on lubricating the machine. 4. Read the Operator’s Manual before servicing or performing maintenance.
decal132-0871 132-0871 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in those conditions on that day and at that site.
Key Switch Product Overview The key switch, used to start and shut off the engine, has 3 positions: OFF, RUN, and START . Refer to Starting the Engine (page 22). Throttle Control The throttle controls the engine speed, and it has a continuous-variable setting from the SLOW to FAST position (Figure 5). Choke Control Use the choke control to start a cold engine. Blade-Control Switch (Power Takeoff) g027333 Figure 4 1. Deck-lift pedal 6. Roll bar 2. Transport lock 7. Seat belt 3.
Fuel Gauge Fuel-Shutoff Valve The fuel gauge is located within the hour meter, and the bars light up when the key switch is in the ON position (Figure 6). Close the fuel-shutoff valve when transporting or storing the machine; refer to Using the Fuel-Shutoff Valve (page 28). The indicator light appears when the fuel level is low (approximately 1 gallon remaining in the fuel tank).
Operation • Do not fill containers inside a vehicle or on a truck or trailer bed with a plastic liner. Always place containers on the ground, away from your vehicle before filling. Note: Determine the left and right sides of the machine from the normal operating position. • Remove the equipment from the truck or trailer and refuel it while it is on the ground. If this is not possible, then refuel from a portable container rather than a fuel-dispenser nozzle.
Adding Fuel Note: Do not fill the fuel tank completely full. The empty space in the tank allows the fuel to expand. Recommended Fuel • For best results, use only clean, fresh (less than 30 days old), unleaded gasoline with an octane rating of 87 or higher ((R+M)/2 rating method). • Ethanol: Gasoline with up to 10% ethanol (gasohol) or 15% MTBE (methyl tertiary butyl ether) by volume is acceptable. Ethanol and MTBE are not the same. Gasoline with 15% ethanol (E15) by volume is not approved for use.
Using the Rollover-Protection System (ROPS) WARNING To avoid injury or death from rollover, keep the roll bar in the fully raised, locked position and use the seat belt. Ensure that the seat is secured to the machine. WARNING There is no rollover protection when the roll bar is in the down position. • Lower the roll bar only when absolutely necessary. • Do not wear the seat belt when the roll bar is in the down position. • Drive slowly and carefully. • Raise the roll bar as soon as clearance permits.
Testing the Safety-Interlock System Using the Safety-Interlock System Service Interval: Before each use or daily WARNING Test the safety-interlock system before you use the machine each time. If the safety system does not operate as described below, have an Authorized Service Dealer repair the safety system immediately. If the safety-interlock switches are disconnected or damaged, the machine could operate unexpectedly, causing personal injury. 1.
Positioning the Seat Changing the Seat Suspension The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure 10). The seat is adjustable to provide a smooth and comfortable ride. Position the seat where you are most comfortable. To adjust it, turn the knob in front either direction to provide the best comfort (Figure 12).
• Keep your hands and feet away from the cutting units. Keep clear of the discharge opening at all times. • Look behind and down before backing up to be sure of a clear path. • Use care when approaching blind corners, shrubs, g229846 Figure 13 trees, or other objects that may obscure your vision. 1. Wear hearing protection. • Do not mow near drop-offs, ditches, or embankments. The machine could suddenly roll over if a wheel goes over the edge or if the edge gives way.
Operating the Parking Brake distance (twice the width of the machine) between the machine and any hazard. Use a walk-behind machine or a hand trimmer to mow the grass in these areas. Always engage the parking brake when you stop the machine or leave it unattended. • Avoid starting, stopping, or turning the machine on slopes. Avoid making sudden changes in speed or direction; turn slowly and gradually.
Operating the Mower Operating the Choke Blade-Control Switch (PTO) Use the choke to start a cold engine. The blade-control switch (PTO) starts and stops the mower blades and any powered attachments. Engaging the Blade-Control Switch (PTO) 1. Pull up the choke knob to engage the choke before using the key switch (Figure 20). 2. Push down the choke knob to disengage the choke after the engine has started (Figure 20).
Starting the Engine Shutting Off the Engine Important: Do not engage starter for more than 5 seconds at a time. If the engine fails to start, wait 15 seconds between attempts. Failure to follow these instructions can burn out the starter motor. CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Note: You may need multiple attempts to start the engine the first time after adding fuel to an empty fuel system.
Using the Motion-Control Levers WARNING The machine can spin very rapidly. You may lose control of the machine and cause personal injury or damage to the machine. • Use caution when making turns. • Slow the machine down before making sharp turns. Driving Forward Note: The engine shuts off when you move the traction-control with the parking brake engaged. To stop the machine, pull the motion-control levers to the NEUTRAL position. 1.
Driving Backward Using the Side Discharge 1. Move the levers to the center, unlocked position. 2. To go backward, slowly pull the motion-control levers rearward (Figure 25). The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. DANGER Without a grass deflector, discharge cover, or a complete grass-catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris.
Adjusting the Height of Cut Adjusting the Height-of-Cut Pin Using the Transport Lock The height-of-cut is adjusted from 25 to 140 mm (1 to 5-1/2 inches) in 6 mm (1/4 inch) increments by relocating the clevis pin into different hole locations. The transport lock has 2 positions, and is used with the deck-lift pedal. There is a LOCK position and an UNLOCK position for the transport position of the mower deck (Figure 26). 1. Move the transport lock to the lock position. 2.
Adjusting the Anti-Scalp Rollers Whenever you change the height-of-cut, adjust the height of the anti-scalp rollers. 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. g029957 Figure 30 Adjust the anti-scalp rollers as shown in Figure 28, Figure 29, and Figure 30. 1. Anti-scalp roller 4. Flange nut 2. Spacer 5. Bolt 3.
Position B Use this position when bagging. Always align it with the blower opening. g027727 Figure 31 Positioning the Flow Baffle The following figures are only recommendations for use. Adjustments vary by grass type, moisture content, and the height of the grass. g005833 Figure 33 Note: If the engine power draws down and the mower ground speed is the same, open up the baffle. Position C Position A This is the full open position.
Operating Tips drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward. Using the Fast Throttle Setting For best mowing and maximum air circulation, operate the engine at the FAST position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower deck in uncut grass.
2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Rotate the release-valve levers vertically to push the machine (Figure 36). Note: This allows hydraulic fluid to bypass the pump, enabling the wheels to turn. 4. Disengage the parking brake before pushing the machine. g008948 Figure 35 1. ON position 2. OFF position Using the Drive-Wheel-Release Valves g015123 Figure 36 WARNING 1.
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.
1. If using a trailer, connect it to the towing vehicle and connect the safety chains. 2. If applicable, connect the trailer brakes and lights. 3. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 37). 4. Back the machine up the ramp (Figure 38). g028043 Figure 38 1. Back the machine up the ramp. 2. Drive the machine forward down the ramp. 5. Shut off the engine, remove the key, and engage the parking brake. 6.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 100 hours • Check the wheel lug-nut torque. • Check the wheel-hub slotted-nut torque. • Check the parking brake adjustment. After the first 250 hours • Change the hydraulic filters and hydraulic fluid when using any type of fluid. Before each use or daily • • • • • • • • Check the safety system. Check the engine-oil level. Check the seat belt. Check the roll bar knobs.
CAUTION If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. Pre-Maintenance Procedures other manufacturers could be dangerous, and such use could void the product warranty. • Check the parking brake operation frequently. Adjust and service as required. Maintenance Safety • Before repairing the machine do the following: – Disengage the drives.
Lubrication Greasing the Mower Deck Service Interval: Yearly—Grease the pump-belt-idler arm. Yearly—Grease the front caster pivots (more often in dirty or dusty conditions). Yearly—Repack the front caster-wheel bearings (more often in dirty or dusty conditions). Greasing the Machine Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: No. 2 lithium or molybdenum grease 1.
5. Note: Keep the dust cap off until greasing is Lubricating the Caster-Wheel Hubs done. Service Interval: Yearly Remove the dust cap and adjust the caster pivots. 6. Remove the hex plug. 7. Thread a grease fitting into the hole. 8. Pump grease into the fitting until it oozes out around the top bearing. 9. Remove the grease fitting in the hole. 10. 1. Park the machine on a level surface, disengage the blade-control switch, and engage the parking brake. 2.
12. 13. Note: Make sure that the axle does not extend Insert the assembled nut and axle into the wheel on the side of the wheel with the new seal and bearing. beyond either nut. With the open end of the wheel facing up, fill the area inside the wheel around the axle full of general-purpose grease. 14. Insert the second bearing and new seal into the wheel. 15. Apply a thread-locking adhesive to the second spacer nut, and thread it onto the axle with the wrench flats facing outward. 16.
Note: Ensure that the primary filter is fully seated by pushing on the outer rim while installing it. Important: Do not press on the soft, inside area of the filter. 4. Install the air-cleaner cover and secure the latches (Figure 46). Servicing the Engine Oil Engine Oil Specifications Oil Capacity: with a filter change—1.9 L (64 fl oz); without a filter change—1.6 L (54 fl oz) g012997 Viscosity: See the table below. Figure 46 1. Inner filter 2. Primary filter 4. Latch 5. Air-cleaner body 3.
Changing the Engine Oil Service Interval: Every 100 hours (more often in dirty or dusty conditions). Note: Dispose of the used oil at a recycling center. 1. Start the engine and let it run for 5 minutes. Note: This warms the oil so that it drains better. 2. Park the machine so that the drain side is slightly lower than the opposite side to ensure that the oil drains completely. 3. Disengage the blade-control switch (PTO) and engage the parking brake. 4.
6. Changing the Engine-Oil Filter Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 50). Service Interval: Every 200 hours—Change the engine-oil filter (more often in dirty or dusty conditions). 1. Drain the oil from the engine; refer to Changing the Engine Oil (page 38). 2. Change the engine-oil filter (Figure 51). g027660 Figure 50 7. Start the engine and drive to a flat area. 8.
Servicing the Spark Plug Service Interval: Every 500 hours—Check, clean and regap the spark plug. Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug(s) and a gapping tool/feeler gauge to check and adjust the air gap. Install a new spark plug(s) if necessary. g009922 Type : Champion® XC12YC, or equivalent Air Gap: 0.76 mm (0.030 inch) Removing the Spark Plug 1.
5. Checking the Spark Arrester Install the left hydraulic-unit shroud (Figure 52). Checking the Spark Plug For Machines with a Spark Arrester Important: Replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, cracks or reuse is questionable. Service Interval: Every 50 hours If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means that the air cleaner is dirty.
Fuel System Maintenance WARNING Fuel-system components are under high pressure. The use of improper components can result in system failure, fuel leakage, and possible explosion. Use only approved fuel lines and fuel filters. Servicing the Electronic Fuel-Injection System g008963 Figure 56 This machine contains an electronic fuel-injection system. It controls the fuel flow under different operating conditions. 1. Fuel filter 2.
Electrical System Maintenance 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Remove the battery as shown in Figure 57. Electrical System Safety • Disconnect the battery before repairing the machine. Disconnect the negative terminal first and the positive last. Connect the positive terminal first and the negative last. • Charge the battery in an open, well-ventilated area, away from sparks and flames.
Installing the Battery Charging the Battery Note: Position the battery in the tray with the terminal posts opposite from the hydraulic tank (Figure 57). WARNING Charging the battery produces gasses that can explode. Never smoke near the battery and keep sparks and flames away from the battery. Important: Always keep the battery fully charged (1.265 specific gravity). This is especially important to prevent battery damage when the temperature is below 0°C (32°F). 1.
Servicing the Fuses DANGER Jump-starting a weak battery that is cracked or frozen or has a low electrolyte level or an open/shorted battery cell can cause an explosion, resulting in serious personal injury. The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check the component/circuit for a malfunction or short. The fuses are located on the console to the right of the seat (Figure 60). 1. To replace the fuses, pull out on the fuse to remove it. 2.
Drive System Maintenance Checking the Seat Belt Service Interval: Before each use or daily Inspect the seat belt for wear, cuts, and proper operation of the retractor and buckle. Replace the seat belt if it is damaged. g012785 Figure 61 1. Positive (+) cable on discharged battery 5. Booster battery 2. Positive (+) cable on booster battery 6. Discharged battery 3. Negative (–) cable on the booster battery 7. Engine block Checking the Roll-Bar Knobs Service Interval: Before each use or daily 4.
Adjusting the Tracking 1. Disengage the blade-control switch (PTO). 2. Drive to an open flat area, move the motion-control levers to the NEUTRAL-LOCK position. 3. Move the throttle midway between fast and slow. 4. Move both motion-control levers all the way forward until they both hit the stops in the T-slot. 5. Check which way the machine tracks. • If it tracks to the right, loosen the bolts and adjust the left stop plate rearward on the left T-slot until the machine tracks straight (Figure 65).
Checking the Tire Pressure Service Interval: Every 50 hours/Monthly (whichever comes first) Maintain the air pressure in the front and rear tires at 90 kPa (13 psi). Uneven tire pressure can cause uneven cut. Check the tires when they are cold to get the most accurate pressure reading. g001055 Figure 66 g024121 Figure 67 1. Slotted nut Checking the Wheel Lug Nuts Adjusting the Caster-Pivot Bearing Check and torque the wheel lug nuts to 122 to 129 N∙m (90 to 95 ft-lb).
2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Using an air compressor, blow out any debris from under the brake pole and around the brake spacers (Figure 70). g001297 g010868 Figure 68 1. Spring washers Figure 70 3. Dust cap 2. Locknut 4. Check the condition of the wire-harness leads, connectors, and terminals. Note: Clean or repair as necessary.
Note: Do not discard the shim until the clutch is functioning properly. g010873 Figure 74 1. Feeler gauge g010871 Figure 72 1. Shim C. • If the gap is less than 0.25 mm (0.01 inch), then install the shim; refer to Using the Clutch Shim (page 49). Using a pneumatic line, blow out any debris from under the brake pole and around the brake spacers. D. Torque each bolt (M6 x 1) to 12.3 to 13.7 N∙m (9.5 to 10.5 ft-lb). E. Using a 0.25 mm (0.
Cleaning the Engine-Cooling Fins and Shrouds Cooling System Maintenance Cleaning the Engine Screen and Engine-Oil Cooler Service Interval: Every 100 hours/Yearly (whichever comes first) 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Remove the air-intake screen, the recoil starter, and the fan housing (Figure 76). 4.
Brake Maintenance Checking and Cleaning the Hydraulic-Unit Shrouds Adjusting the Parking Brake Service Interval: Before each use or daily 1. 2. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. Service Interval: After the first 100 hours Every 500 hours thereafter Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Move the seat forward. 4.
Belt Maintenance Inspecting the Belts Service Interval: Every 50 hours Replace the belt if it is worn. The signs of a worn belt include squealing while the belt is rotating; the blades slipping while cutting grass; and frayed edges, burn marks, and cracks on the belt. Replacing the Mower Belt g026961 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2.
g027730 Figure 81 1. Position the belt cover 3. Ensure that the tab is under the metal catch 2. Slide the belt cover under the side catches g009038 Replacing the Hydraulic Pump-Drive Belt Figure 80 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler-grease fitting 3. Spring-loaded idler pulley 7. Belt guide 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2.
Controls System Maintenance Adjusting the Control-Handle Position There are 2 height positions for the control levers—high and low. Remove the bolts to adjust the height for the operator. 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Loosen the bolts and flange nuts installed in the levers (Figure 83). 4.
4. Lower deck to the ground. 5. Raise the rear of machine up and support it with jack stands (or equivalent support). Note: Raise the machine just high enough to allow the drive wheels to turn freely. 6. Remove the electrical connection from the seat safety switch, located under the bottom cushion of the seat. Note: The switch is a part of the seat assembly. 7. Temporarily install a jumper wire across the terminals in the connector of the main wire harness. 8.
g008620 Figure 86 Right Motion Control Shown 1. Torque the locknut to 23 N∙m (17 ft-lb). The bolt must protrude past the end of the locknut after torquing. 2. Most resistance (firmest feel) 3. Damper 4. Medium resistance (medium feel) g010187 5. Least resistance (softest feel) Figure 85 1. Double nuts 12.
Hydraulic System Maintenance 6. Remove 1 dipstick from the hydraulic reservoir (Figure 88). 7. Wipe the dipstick off and thread the dipstick into the reservoir. Hydraulic System Safety 8. Remove the dipstick and look at the end (Figure 88). • Seek immediate medical attention if fluid is injected Important: Do not overfill the hydraulic into skin. Injected fluid must be surgically removed within a few hours by a doctor. units with fluid, as damage may occur.
Replacing the Hydraulic Fluid and Filters Service Interval: After the first 250 hours—Change the hydraulic filters and hydraulic fluid when using any type of fluid. Every 250 hours—Change the hydraulic filters and hydraulic fluid when using Mobil® 1 fluid (more often in dirty or dusty conditions). Every 500 hours—Change the hydraulic filters and hydraulic fluid when using Toro® HYPR-OIL™ 500 hydraulic fluid (more often in dirty or dusty conditions).
Mower Deck Maintenance Note: The measurement should read 7.6 mm (3 inches) Leveling the Mower Deck Leveling the Deck 1. 2. 3. 4. 5. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Check the tire pressure in the drive tires; refer to Checking the Tire Pressure (page 48). Position the transport lock in the latching position.
11. Note: In most conditions, the back blade tip To adjust the single-point system, loosen the 2 bolts at the bottom of the height-of-cut plate (Figure 94). should be adjusted 6.4 mm (1/4 inch) higher than the front. 14. Torque the 2 bolts to 37 to 45 N∙m (27 to 33 ft-lb). 15. On both sides of the deck, measure from the level surface to the back tip of the blade (postion B) as shown in Figure 92. Note: The measurement should read 8.3 cm (3-1/4 inches) 16.
Servicing the Cutting Blades To ensure a superior quality of cut, keep the blades sharp. For convenient sharpening and replacement, you may want to keep extra blades on hand. Blade Safety g006530 Figure 96 A worn or damaged blade can break, and a piece of the blade could be thrown toward you or bystanders, resulting in serious personal injury or death. Trying to repair a damaged blade may result in discontinued safety certification of the product. • Inspect the blades periodically for wear or damage.
Removing the Blades Replace the blades if they hit a solid object, or if the blade is out of balance or bent. 1. Hold the blade end using a rag or thickly padded glove. 2. Remove the blade bolt, curved washer, and blade from the spindle shaft (Figure 98). g000553 Figure 100 1. Blade 3. 2. Balancer Repeat this procedure until the blade is balanced. Installing the Blades 1. Install the blade onto the spindle shaft (Figure 98).
5. Lift up the floor pan and insert a ratchet into the square hole in the deck idler (Figure 101). 6. Rotate the deck idler clockwise and remove the mower belt (Figure 101). g010252 Figure 102 1. Right stabilizer 2. Deck strut (right side shown) 3. Remove the shoulder bolt and nut. 4. Remove the shoulder bolt and nut. Figure 101 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease fitting 3. Spring-loaded idler pulley 7. Belt guide 9.
Cleaning Cleaning under the Mower Deck Service Interval: Before each use or daily 1. Park the machine on a level surface, disengage the blade-control switch (PTO), and engage the parking brake. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Raise the mower deck to the TRANSPORT position. g015594 Figure 103 1. Bolt 5. Spring installed 2. Spacer 6. Grass deflector 3. Locknut 7. J-hook end of spring 4.
Storage 13. Storage Safety Prepare the machine for storage when non-use occurs over 30 days. Prepare the machine for storage as follows: A. • Shut off the engine, remove the key, wait for all moving parts to stop, and allow the machine to cool before storing it. • Do not store the machine or fuel near flames or drain the fuel indoors. Add a petroleum-based stabilizer/conditioner to fuel in the tank. Follow mixing instructions from the stabilizer manufacturer.
Troubleshooting Problem The malfunction-indicator light (MIL) comes on. Possible Cause 1. The engine is too hot. 1. Shut off the engine and let it cool. 2. There is old fuel in the fuel tank. 3. The fuel-shutoff valve is not open completely. 4. The air cleaner is dirty. 2. Use new fuel. 3. Open the fuel-shutoff valve. 5. The battery is not charged. 6. Incorrect fuel filters are being used or the fuel filters are dirty. 7.
Problem The engine loses power. The engine overheats. Possible Cause 1. The engine load is excessive. 1. Reduce the ground speed. 2. The air cleaner is dirty. 3. The oil level in the crankcase is low. 4. The cooling fins and the air passages above the engine are plugged. 5. The vent hole in the fuel cap is plugged. 6. There is dirt in the fuel filter. 7. There is dirt, water, or stale fuel in the fuel system. 2. Clean the air-cleaner element. 3. Add oil to the crankcase. 4.
Problem The blades do not rotate. Possible Cause 1. The mower deck belt is damaged, worn, loose, or broken. 1. Install a new deck belt. 2. The mower deck belt is off the pulley. 2. Install the mower belt on the deck pulley and check the idler pulley, idler arm, and spring for correct position and function. 3. Check the belt tension or install a new belt. 4. Replace the spring. 3. The pump drive belt is worn, loose, or broken. 4. The idler spring is broken or missing. The clutch does not engage.
GND BK BK + - A C FUEL SENDER S B BU PK (PTO SWITCH) SW2 PK PK 2 3 BN BN BN V 4 5 BK BK U2 BK F4 PK 7 4 9 HOUR METER 7 W PK 12 OR 10 T SW6 (BRAKE) GND 15A 6 2 3 Y 11 LTGR SW4 (NEUT_L) BN 8 B PTO CLUTCH TVS DIODE BK A BN F3 SW5 (NEUT_R) PTO 1 PK FUEL_SOLENOID NEUTRAL 8 SEAT OR BRAKE 5 8 4 7 10A KEY_A 1 GN SW7 (SEAT) BN PK OR GY R OR R GY PK PK GY V SW1 (IGNITION) 2 5 1 3 B I S R 5 GN 2 OPTIONAL ACCESSORIES FUEL GROUND Electrical Schematic
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.