Setup Instructions

ManualsBrandsToro ManualsOutdoor Power EquipmentTimeCutter HD with MyRIDE 54 in. Fab 24.5 HP V-Twin Gas Zero-Turn Riding Mower with Smart Speed

FormNo.3410-234RevB

TimeCutter

HDRidingMower

ModelNo.74864—SerialNo.400000000andUp

ModelNo.74865—SerialNo.400000000andUp

ModelNo.74866—SerialNo.400000000andUp

ModelNo.74867—SerialNo.400000000andUp

ModelNo.75201—SerialNo.400000000andUp

ModelNo.75202—SerialNo.400000000andUp

ModelNo.75203—SerialNo.400000000andUp

ModelNo.75210—SerialNo.400000000andUp

ModelNo.75211—SerialNo.400000000andUp

ModelNo.75212—SerialNo.400000000andUp

ModelNo.75213—SerialNo.400000000andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Connectthebattery.

Rearhitch1

Bolt(5/16x1inch)

Locknut(5/16inch)

Installtherearhitch.

Nopartsrequired

–

Setupthemotion-controllevers(CE

machinesonly).

Nopartsrequired

–

Checkthemoweradjustment.

Ignitionkey1

Hosecoupling(non-CEmachinesonly)

Operator'sManual

Engineowner’smanual(non-Toro

enginesonly)

Operatortrainingmaterial

Completethesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3410-234*B

Summary of content (4 pages)

PAGE 1
Form No. 3410-234 Rev B TimeCutter® HD Riding Mower Model No. 74864—Serial No. 400000000 and Up Model No. 74865—Serial No. 400000000 and Up Model No. 74866—Serial No. 400000000 and Up Model No. 74867—Serial No. 400000000 and Up Model No. 75201—Serial No. 400000000 and Up Model No. 75202—Serial No. 400000000 and Up Model No. 75203—Serial No. 400000000 and Up Model No. 75210—Serial No. 400000000 and Up Model No. 75211—Serial No. 400000000 and Up Model No. 75212—Serial No. 400000000 and Up Model No.
PAGE 2
1 Connecting the Battery No Parts Required Procedure WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. g197768 1. Loosen the 2 fasteners on the battery cover counterclockwise 1/4 turn and remove the battery cover (Figure 1). Figure 2 g190587 Figure 1 2. Remove the plastic cap from the negative battery post. 3.
PAGE 3
2 3 Installing the Rear Hitch Setting Up the Motion-Control Levers Parts needed for this procedure: 1 Rear hitch 2 Bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) CE Machines Only No Parts Required Procedure Procedure 1. Locate the motion-control levers attached, but folded down on the machine. Install the bracket to the frame as shown in Figure 3 and Figure 4. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3.
PAGE 4
5 Completing the Setup Parts needed for this procedure: 1 Ignition key 1 Hose coupling (non-CE machines only) 1 Operator's Manual 1 Engine owner’s manual (non-Toro engines only) 1 Operator training material Checking the Tire Pressure Check the front and rear tires for proper inflation; refer to Checking the Tire Pressure in the Operator’s Manual for the recommended inflation pressure.