Form No. 3456-108 Rev A TimeCutter® MyRIDE® 42in, 50in, or 54in Riding Mower Model No. Model No. Model No. Model No. Model No. Model No. Register at www.Toro.com. Original Instructions (EN) 75747—Serial No. 412562015 and Up 75747TA—Serial No. 400000000 and Up 75747W—Serial No. 412090000 and Up 75756—Serial No. 412515219 and Up 75758TA—Serial No. 412540000 and Up 75761TA—Serial No.
It is a violation of California Public Resource Code Section 4442 or 4443 to use or operate the engine on any forest-covered, brush-covered, or grass-covered land unless the engine is equipped with a spark arrester, as defined in Section 4442, maintained in effective working order or the engine is constructed, equipped, and maintained for the prevention of fire. Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage.
• Danger indicates an imminently hazardous Cleaning the Machine ....................................... 26 Pushing the Machine by Hand .......................... 26 Transporting the Machine ................................. 27 Maintenance ........................................................... 29 Maintenance Safety.......................................... 29 Recommended Maintenance Schedule(s) ........... 30 Pre-Maintenance Procedures .............................. 30 Raising the Machine .............
Safety This machine has been designed in accordance with ANSI B71.1-2017. General Safety This product is capable of amputating hands and feet and of throwing objects. Always follow all safety instructions to avoid serious personal injury or death. • Read and understand the contents of this Operator’s Manual before starting the engine. • Keep bystanders and children away. • Do not allow children or untrained people to operate or service the machine.
Slope Indicator g011841 Figure 3 You may copy this page for personal use. 1. The maximum slope you can operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Decal 99-3943 is for models with 127 cm (50 inch) or 137 cm (54 inch) decks only. decalbatterysymbols Battery Symbols Some or all of these symbols are on your battery. 1. Explosion hazard 6. Keep bystanders away from the battery. 2. No fire, open flame, or smoking 7.
Decal 112-9840 is for models with 127 cm (50 inch) or 137 cm (54 inch) decks only. decal132-0872 132-0872 decal112-9840 112-9840 3. Remove the ignition key and read the instructions before servicing or performing maintenance. 1. Read the Operator's Manual. 1. Thrown object hazard—keep bystanders away from the machine. 3. Severing hazard of hand or foot—keep away from moving parts. 2. Thrown object hazard, raised deflector—do not operate the machine with an open deck; use a bagger or a deflector. 4.
decal139-2388 139-2388 1. Slow 2. Hauling 3. Fast Decal 139-2391 is for models without an hour meter. decal139-2392 139-2392 decal139-2394 139-2394 decal139-2391 139-2391 1. Fast 1. Traction controls 2. Fast 3. Slow 2. Slow 8 4. Neutral 5. Reverse 6.
decal139-2395 139-2395 1. Parking brake 4. Neutral 2. Fast 3. Slow 5. Reverse 6. Traction controls decal139-2397 139-2397 Decal 140-2717 is for models with an hour meter. decal140-2717 140-2717 1. Fast 2.
decal132-0869 132-0869 Note: This machine complies with the industry standard stability test in the static lateral and longitudinal tests with the maximum recommended slope indicated on the decal. Review the instructions for operating the machine on slopes in the Operator’s Manual as well as the conditions in which you would operate the machine to determine whether you can operate the machine in the conditions on that day and at that site.
Product Overview g367815 Figure 4 1. Engine 4. Motion-control levers 7. Smart Speed™ lever 10. Rear drive wheel 2. Operator seat 5. Front caster wheel 8. Height-of-cut lever 11. Control panel 3. Fuel-tank cap 6. Deck-lift pedal (certain models only) 9. Deflector 12.
Controls Motion-Control Levers Become familiar with all the controls before you start the engine and operate the machine. Use the motion-control levers to drive the machine forward, reverse, and turn either direction (Figure 4). Control Panel Park Position Move the motion-control levers outward from the center to the PARK position when exiting the machine to engage the electric brake (Figure 20).
Height-of-Cut Lever Operation Use the height-of-cut lever to lower and raise the deck from the seated position. Moving the lever up (toward you) raises the deck from the ground and moving the lever down (away from you) lowers the deck toward the ground. Adjust the height-of-cut only while the machine is not moving (Figure 24). Note: Determine the left and right sides of the machine from the normal operating position.
Adding Fuel Fuel Safety • Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. Recommended Fuel – To prevent a static charge from igniting the fuel, remove the machine from the truck or trailer and refuel it on the ground, away from all vehicles.
Understanding the Safety-Interlock System The safety-interlock system is designed to prevent the engine from starting unless: • The blade-control switch (PTO) is disengaged. • The motion-control levers are in the PARK position. The safety-interlock system also is designed to shut off the engine whenever the control levers are out of the PARK position and you rise from the seat. Testing the Safety-Interlock System Test the safety-interlock system before you use the machine each time.
Positioning the Seat The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable (Figure 8). g292102 Figure 9 1. MyRide adjustment lever 3. Firmer suspension 2. Softer suspension g027632 Adjusting the Motion-Control Levers Figure 8 Adjusting the MyRide® Suspension System Adjusting the Height You can adjust the motion-control levers higher or lower for maximum comfort (Figure 10).
• Do not mow in reverse unless it is absolutely necessary. Always look down and behind you before moving the machine in reverse. • Use extreme care when approaching blind corners, shrubs, trees, or other objects that may block your view. • Stop the blades whenever you are not mowing. • If the machine strikes an object or starts to vibrate, immediately shut off the engine, remove the key (if equipped), and wait for all moving parts to stop before examining the machine for damage.
• Clean grass and debris from the cutting unit, • • • • • • • • • machine could suddenly roll over if a wheel goes over the edge or the edge collapses. Keep a safe distance (twice the width of the machine) between the machine and any hazard. Use a walk-behind machine or a hand trimmer to mow the grass in these areas. drives, muffler, and engine to help prevent fires. Start the engine with your feet well away from the blades. Be aware of the mower discharge path and direct the discharge away from others.
Towing Safety Operating the Mower Blade-Control Switch (PTO) • Do not attach towed equipment except at the hitch point. The blade-control switch (PTO) starts and stops the mower blades and any powered attachments. • Do not use the machine as a towing vehicle unless it has a hitch installed. • Do not exceed the weight limits for towed Engaging the Blade-Control Switch (PTO) equipment and towing on slopes. The towed weight must not exceed the weight of the machine and operator.
Operating the Throttle Starting the Engine You can move the throttle control between the FAST and SLOW positions (Figure 17). Note: A warm or hot engine may not require choking. Always use the FAST position when engaging the PTO. than 5 seconds at a time. Engaging the starter motor for more than 5 seconds can damage the starter motor. If the engine fails to start, wait 10 seconds before operating the engine starter again.
Driving the Machine Shutting Off the Engine 1. Disengage the blades by moving the blade-control switch to the OFF position. 2. Move the motion-control levers outward to the PARK position. 3. Move the throttle control to between the half and full throttle position. 4. Turn the key to the OFF position and remove the key. The drive wheels turn independently, powered by hydraulic motors on each axle.
Driving Backward 1. Move the levers to the center, unlocked position. 2. To go backward, slowly pull the motion-control levers rearward (Figure 22). 2. Disengage the blade-control switch. 3. Adjust the lever to the desired position. The following are only recommendations for use. Adjustments vary by grass type, moisture content, and the height of the grass.
Using the Side Discharge Adjusting the Height of Cut The mower has a hinged grass deflector that disperses clippings to the side and down toward the turf. Note: The transport position is the highest height-of-cut position or cutting height at 114 mm (4-1/2 inches) as shown in Figure 24. You can adjust the height of cut from 38 to 114 mm (1-1/2 to 4-1/2 inches) in 13 mm (1/2 inch) increments. The height of cut is controlled by the lever located to the right of the operating position (Figure 24).
Machines with 127 cm (50-inch) or 137 cm (54-inch) Mower Decks Adjusting the Anti-Scalp Rollers Whenever you change the height of cut, adjust the height of the anti-scalp rollers. Machines with 107 cm (42-inch) Mower Decks Note: Adjust the anti-scalp rollers so that the rollers do not touch the ground in normal, flat mowing areas. Whenever you change the height of cut, adjust the height of the anti-scalp rollers. 1.
Stopping the Machine Operating Tips If you must stop the forward motion of the machine while mowing, a clump of grass clippings may drop onto your lawn. To avoid this, move onto a previously cut area with the blades engaged or you can disengage the mower deck while moving forward. Maximizing Air Circulation For best mowing and maximum air circulation, operate the engine at the FAST position.
Pushing the Machine by Hand After Operation After Operation Safety This machine has an electric-brake mechanism, and to push the machine, the key must be in the RUN position. The battery needs to be charged and functioning to disengage the electric brake. General Safety • Shut off the engine, remove the key, and wait 1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position. 2.
Transporting the Machine Use a heavy-duty trailer or truck to transport the machine. Use a full-width ramp. Ensure that the trailer or truck has all the necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you or bystanders avoid injury. Refer to your local ordinances for trailer and tie-down requirements.
1. If you are using a trailer, connect it to the towing vehicle and connect the safety chains. 2. If applicable, connect the trailer brakes and lights. 3. Lower the ramp, ensuring that the angle between the ramp and the ground does not exceed 15 degrees (Figure 28). 4. Back the machine up the ramp (Figure 29). g027995 Figure 29 1. Back the machine up the ramp. 5. Shut off the engine, remove the key, and move the motion-control levers outward to the PARK position. 6.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Maintenance Safety • If you leave the key in the switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the switch before you perform any maintenance. • Before you leave the operator’s position, do the following: – Park the machine on a level surface. – Disengage the drives. – Engage the parking brake. – Shut off the engine and remove the key.
Recommended Maintenance Schedule(s) Maintenance Service Interval Before each use or daily Maintenance Procedure • • • • Check the safety-interlock system. Check the engine-oil level. Inspect the blades. Inspect the grass deflector for damage. After each use • Clean grass and debris from the cutting unit, muffler, drives, grass catcher, and engine. • Clean the mower-deck housing. • Clean grass and debris from the cutting unit, muffler, drives, grass catcher, and engine.
Lubrication Greasing the Bearings Service Interval: Every 25 hours—Grease the caster wheel bearings (more often in sandy soil conditions). Grease Type: No. 2 lithium grease 1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position. 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Clean the grease fittings (Figure 32) with a rag. g299647 Figure 31 1.
Engine Maintenance 5. Separate the foam and paper elements (Figure 34). Engine Safety • Keep your hands, feet, face, other body parts, and clothing away from the muffler and other hot surfaces. Allow engine components to cool before performing maintenance. Do not change the engine governor speed or overspeed the engine. • g333887 Figure 34 Servicing the Air Cleaner 1. Paper element Service Interval: Every 25 hours—Clean the air-cleaner foam element (more often in dusty, dirty conditions).
Servicing the Paper Air-Cleaner Element Checking the Engine-Oil Level Service Interval: Every 100 hours or yearly, whichever comes first—Replace the paper air-cleaner element (more often in dirty or dusty conditions). Note: Check the oil when the engine is cold. 1. Service Interval: Before each use or daily Important: If you overfill or underfill the engine crankcase with oil and run the engine, you may damage the engine. Clean the paper element by tapping it gently to remove dust. 1.
Changing the Engine Oil and Oil Filter Service Interval: Every 100 hours or yearly, whichever comes first—Change the engine oil and oil filter (more often in dirty or dusty conditions). 1. Park the machine on a level surface to ensure that the oil drains completely. 2. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position. 3.
Servicing the Spark Plug Service Interval: Every 100 hours or yearly, whichever comes first—Check the spark plug(s). Every 200 hours/Every 2 years (whichever comes first)—Replace the spark plug(s). Ensure that the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug and a gapping tool or feeler gauge to check and adjust the air gap. Install a new spark plug if necessary.
Fuel System Maintenance DANGER In certain conditions, fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others and can damage property. g206628 Figure 41 Refer to Fuel Safety (page 14) for a complete list of fuel related precautions. Installing the Spark Plug Replacing the In-Line Fuel Filter Service Interval: Every 100 hours—Replace the in-line fuel filter. Never install a dirty filter after removing it from the fuel line. g027480 Figure 42 1.
Electrical System Maintenance Electrical System Safety g365941 • Disconnect the cable from the negative terminal of the battery before repairing the machine. • Charge the battery in an open, well-ventilated area, away from sparks and flames. Unplug the charger before connecting or disconnecting the battery. Wear protective clothing and use insulated tools. Servicing the Battery Removing the Battery WARNING Battery terminals or metal tools could short against metal machine components, causing sparks.
Charging the Battery WARNING Incorrectly removing the cables from battery could damage the machine and cables, causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. Service Interval: Before storage—Charge the battery and disconnect the battery cables. • Always disconnect the negative (black) battery cable before disconnecting the positive (red) cable. 1. Remove the battery from the chassis; refer to Removing the Battery (page 37). 2.
Servicing the Fuses Drive System Maintenance The electrical system is protected by fuses. It requires no maintenance; however, if a fuse blows, check the component/circuit for a malfunction or short. Checking the Tire Pressure Fuse type: • Main—F1 (25 A, blade-type) Service Interval: Every 25 hours—Check tire pressure. • Charge Circuit—F2 (15 A, blade-type) 1. Park the machine on a level surface, disengage the blade-control switch, and move the motion-control levers outward to the PARK position. 2.
Releasing the Electric Brake 4. Note: Rotate the bolt a small amount to make minor adjustments. You can manually release the electric brake by rotating the link arms forward. Once the electric brake is energized, the brake resets. 1. Turn the key to the the key. 2. Disconnect the battery. 3. Locate the shaft on the electric brake where the brake link arms are connected (Figure 48). 4. Rotate the shaft forward to release the brake. 5. Connect the battery after moving the machine.
Belt Maintenance Inspecting the Belts Service Interval: Every 25 hours—Check the belts for wear or cracks. Replace the belt if it is worn. The signs of a worn belt include squealing while the belt is rotating; the blades slipping while cutting grass; and frayed edges, burn marks, and cracks on the belt.
Mower Maintenance Blade Safety • Inspect the blades periodically for wear or damage. • Use care when checking the blades. Wrap the blades or wear gloves, and use caution when servicing the blades. Only replace or sharpen the blades; never straighten or weld them. • On multi-bladed machines, take care as rotating one blade can cause other blades to rotate. • Replace worn or damaged blades and bolts in sets to preserve balance. Servicing the Cutting Blades g298026 Figure 53 Mower decks with 3 blades 1.
g006530 Figure 54 1. Cutting edge 3. Wear/slot forming 2. Curved area 4. Crack g014973 Figure 56 1. Blade (in position for measuring) Checking for Bent Blades 2. Level surface 3. Measured distance between blade and the surface (A) Note: The machine must be on a level surface for the following procedure. 4. 1. Raise the mower deck to the highest height-of-cut position. 2.
g014973 Figure 58 g027833 1. Opposite blade edge (in position for measuring) Figure 59 2. Level surface 3. Second measured distance between blade and surface (B) A. 1. Sail area of the blade 2. Blade If the difference between A and B is greater than 3 mm (1/8 inch), replace the blade with a new blade; refer to Removing the Blades (page 44) and Installing the Blades (page 45). Sharpening the Blades 1.
Installing the Blades 1. Install the blade onto the spindle shaft (Figure 59). Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. 2. Install the curved washer (cupped side toward the blade) and the blade bolt (Figure 59). 3. Torque the blade bolt to 81 to 108 N∙m (60 to 80 ft-lb).
2. 3. 4. 5. Leveling from Side to Side Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. Set the height of cut to 76 mm (3 inches). Carefully rotate the blades so they are facing front to rear (Figure 64). Measure from the tip of the front blade to the flat surface and the tip of the rear blade to the flat surface (Figure 64 or Figure 65). Note: If the front blade tip is not 1.6 to 7.9 mm 1. Move to the left side of the machine. 2.
g294195 Figure 69 8. Install the washer and hairpin cotter (Figure 69). 9. Repeat steps 6 through 8 for the other side of the machine. 10. Check the side-to-side level again; repeat this procedure until the measurements are correct. 11. Continue leveling the mower deck by checking the front-to-rear blade slope; refer to Checking the Front-to-Rear Blade Slope (page 45). g298028 Figure 67 Mower Decks with 3 Blades 1. Wood block—6.6 cm (2-5/8 inches) thick 6. 2. Wood block—7.
3. To lower the front of the mower deck, loosen the adjustment nut. 4. After adjustment, check the front-to-rear slope again, continue adjusting the nut until the front blade tip is 1.6 to 7.9 mm (1/16 to 5/16 inch) lower than the rear blade tip; refer to Checking the Front-to-Rear Blade Slope (page 45). 5. When the front-to-rear blade slope is correct, check the side-to-side level of the mower deck again; refer to Leveling from Side to Side (page 46). Removing the Mower Deck 1.
8. Attach the front support rod to the mower deck with the clevis pin and hairpin cotter (Figure 71). 7. Slide the rod through the second grass-deflector pivot (Figure 73). 9. Install the mower belt onto the engine pulley; refer to Replacing the Mower Belt (page 41). 8. Insert the rod at the front of the grass deflector into the bracket on the deck. 9. Secure the rear end of the rod into the mower with a nut (3/8 inch) as shown in Figure 73.
Cleaning 7. Disengage the blade-control switch, shut off the engine, remove the key, and wait for all moving parts to stop. Washing the Underside of the Mower Deck 8. Turn the water off and remove the coupling from the washout fitting. Note: If the mower is not clean after 1 washing, Service Interval: After each use—Clean the mower-deck housing. soak it and let it stand for 30 minutes. Then repeat the process. 9. Important: You can wash the machine with a mild detergent and water.
Storage Note: Run the machine with the blade-control switch (PTO) engaged and the engine at high idle for 2 to 5 minutes after washing. Storage Safety 12. Check the condition of the blades; refer to Servicing the Cutting Blades (page 42). 13. Prepare the machine for storage for over 30 days as follows: • Shut off the engine, remove the key, and wait for all moving parts to stop before you leave the operator’s position. Allow the machine to cool before adjusting, servicing, cleaning, or storing it.
Storing the Battery 1. Fully charge the battery. 2. Let the battery rest for 24 hours, then check the battery voltage. Note: If the battery voltage is below 12.6 V, repeat steps 1 and 2. 3. Disconnect the cables from the battery. 4. Check the voltage periodically to ensure that the voltage is 12.4 V or higher. Note: If the battery voltage is below 12.4 V, repeat steps 1 and 2.
Troubleshooting Problem Possible Cause The fuel tank is showing signs of collapsing or the machine is frequently showing signs of running out of fuel. 1. The air-cleaner paper element clogged. The engine overheats. 1. The engine load is excessive. 1. Reduce the ground speed. 2. The oil level in the crankcase is low. 3. The cooling fins and air passages under the engine-blower housing are plugged. 4. The air cleaner is dirty. 2. Add oil to the crankcase. 3.
Problem The machine does not drive. The machine vibrates abnormally. The cutting height is uneven. The blades do not rotate. Possible Cause Corrective Action 1. The bypass valves are open. 1. Close the tow valves. 2. The traction belts are worn, loose, or broken. 3. The traction belts are off the pulleys. 4. The transmission has failed. 2. Contact an Authorized Service Dealer. 1. The cutting blade(s) is/are bent or unbalanced. 1. Install new cutting blade(s). 2. The blade mounting bolt is loose.
Schematics g307974 Electrical Diagram 139-2356 (Rev.
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
