Setup Instructions

ManualsBrandsToro ManualsRiding ProductsTimeCutter 42in Riding Mower

FormNo.3437-707RevA

TimeCutter

RidingMowers

ForAllTimeCutter

RidingMowers

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Seatback

Flanged-hexbolt2

Nut2

Installthebackcushion(machineswith

MyRide™suspensionsystemonly).

Nopartsrequired

–

Connectthebattery.

Nopartsrequired

–

Attachtheseat-tiltcable(non-MyRide

machinesonly).

Rearhitch1

Bolt(5/16x1inch)

Locknut(5/16inch)

Installtherearhitch.

Nopartsrequired

–

Setupthemotion-controllevers.

Nopartsrequired

–

Checkthemoweradjustment.

Key1

Hosecoupling(notincludedwithCE

models)

Operator'sManual

Engineowner’smanual(non-Toro

engines)

Operatortrainingmaterial

Completethesetup.

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3437-707*A

Summary of content (4 pages)

PAGE 1
Form No. 3437-707 Rev A TimeCutter® Riding Mowers For All TimeCutter® Riding Mowers Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Qty. Use Seat back Flanged-hex bolt Nut 1 2 2 Install the back cushion (machines with MyRide™ suspension system only). No parts required – Connect the battery. No parts required – Attach the seat-tilt cable (non-MyRide machines only).
PAGE 2
1 2 Installing the Back Cushion Connecting the Battery Machines with MyRide™ Suspension System Only No Parts Required Procedure Parts needed for this procedure: 1 Seat back 2 Flanged-hex bolt 2 Nut Procedure 1. Slide the seat back on to the seat base posts and align the holes. 2. Secure the seat back using 2 flanged-hex bolts and 2 nuts (Figure 1). Torque the bolts to 24 N∙m (18 ft-lb). 1. Locate the battery and negative battery cable. 2.
PAGE 3
4 Attaching the Seat-Tilt Cable Installing the Rear Hitch Parts needed for this procedure: Non-MyRide Machines Only No Parts Required Procedure 1 Rear hitch 2 Bolt (5/16 x 1 inch) 2 Locknut (5/16 inch) Procedure 1. Tilt the seat back partway. 2. Attach the seat-tilt cable from inside the seat pan (Figure 3). Install the bracket to the frame as shown in Figure 4 and Figure 5. g298485 Figure 4 Before assembly g313032 Figure 3 1. Bolts 1. Seat-tilt cable 3. 2.
PAGE 4
5 7 Setting Up the Motion-Control Levers Completing the Setup Parts needed for this procedure: No Parts Required Procedure 1. Locate the motion-control levers attached, but folded down on the machine. 2. Remove the upper bolt (3/8 x 1 inch) and washer; loosen the lower bolt (3/8 x 1 inch). 3. Raise the motion control levers to the upright position. 4.