Setup Instructions

ManualsBrandsToro ManualsRiding Products60in TITAN MAX Riding Mower

FormNo.3449-600RevA

60inTITAN

MAXRidingMower

ModelNo.76601—SerialNo.400000000andUp

ModelNo.76602—SerialNo.400000000andUp

SetupInstructions

Setup

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

ProcedureDescription

Qty.

Use

Nopartsrequired

–

Removethemachinefromthecrate.

Nopartsrequired

–

Addfueltothemachine.

Nopartsrequired

–

Checktheengine-oillevel.

Nopartsrequired

–

Checkthehydraulic-uidlevel.

Nopartsrequired

–

Checkthetirepressure.

Nopartsrequired

–

Chargethebattery.

Nopartsrequired

–

Raisetherollover-protectionsystem

(ROPS).

Nopartsrequired

–

Checkthegrassdeector.

Nopartsrequired

–

Checkthemoweradjustment.

Nopartsrequired

–

Checkthemachinebeforedeliveryto

thecustomer(allmachines).

Operator'sManual

Engineowner'smanual1

Operator-trainingmaterial

Key2

Registrationcard1

Deliverthemachinetothecustomer(all

machines).

Note:Determinetheleftandrightsidesofthemachinefromthenormaloperatingposition.

8111LyndaleAvenueSouth

Bloomington,MN55420Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3449-600*

Summary of content (8 pages)

PAGE 1
Form No. 3449-600 Rev A 60in TITAN® MAX Riding Mower Model No. 76601—Serial No. 400000000 and Up Model No. 76602—Serial No. 400000000 and Up Setup Instructions Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 8 9 10 11 Description Use Qty. No parts required – Remove the machine from the crate. No parts required – Add fuel to the machine. No parts required – Check the engine-oil level.
PAGE 2
1 4 Removing the Machine from the Crate Checking the Hydraulic-Fluid Level No Parts Required No Parts Required Procedure Procedure If removing the machine from a metal crate, refer to the Dealer/Distributor Portal for further information. This machine is shipped filled with hydraulic fluid in the reservoirs. Check the expansion tank; if necessary, add Toro® HYPR-OIL™ 500 hydraulic fluid, as recommended in the Operator's Manual, to the FULL COLD line (Figure 1).
PAGE 3
5 7 Checking the Tire Pressure Raising the Rollover-Protection System (ROPS) No Parts Required Procedure No Parts Required Pressure: 13 psi (90 kPa) Note: Check the tire pressure before starting the machine. Refer to your Operator’s Manual for the correct tire type and procedure. Procedure Important: Always use the seat belt with the roll bar in the raised position. 6 Charging the Battery 1. Remove the hairpin cotters and remove the 2 pins (Figure 2). 2.
PAGE 4
8 Checking the Grass Deflector No Parts Required Procedure If there are plastic ties holding the grass deflector up, remove them and lower the deflector into place. WARNING An uncovered discharge opening could allow the machine to throw objects toward you or bystanders, resulting in serious injury or death. Also, contact with the blade could occur. Never operate the machine without a cover plate, a mulch plate, grass deflector, or bagger installed.
PAGE 5
10 Checking the Machine Before Delivery to the Customer (All Machines) No Parts Required Procedure Before delivering the machine to the customer, ensure that you have performed the procedures listed in the following table and initial each when finished. Refer to the Operator's Manual for instructions on performing these procedures. Initial Check Procedure Check the tire pressure. Check the level of the mower deck. Check the engine-oil level. Check the hydraulic-fluid level. Check that the ROPS is secure.
PAGE 6
11 Delivering the Machine to the Customer (All Machines) Parts needed for this procedure: 1 Operator's Manual 1 Engine owner's manual 1 Operator-training material 2 Key 1 Registration card Procedure At delivery, fill in the model and serial number, complete the items listed in the following table, and initial each when finished. Model No. Dealer Initial Serial No.
PAGE 7
Dealer Initial Customer Initial Check Procedure Refer to the Operator's Manual to point out safety procedures, operation, and maintenance procedures. Review the warranty statement. Describe the post-sale service procedures for your store. Assist the customer in filling out and mailing the registration card or register online at www.Toro.com. Make sure that the customer receives the Operator's Manual, engine owner's manual, Setup Instructions, and operator training material.
PAGE 8