Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78511

W 2004 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

Printed in the USA

Original Instructions (EN)

48in TURBO FORCE Mower Finishing Kit

Z400 Twin Soft Bagger

Model No. 78511

Form No. 3352-634

Installation Instructions

Setup

Important These instructions are for Z400 machines only.

Note: Determine the left and right sides of the machine from the normal operating position.

Loose Parts

Note: Use the chart below to verify all parts have been shipped.

Step

Description Qty. Use

No parts needed Removing the existing mower cover

Rear hinge bracket

Hex socket screw, 3/8 x 1-1/4

Flange nut, 3/8 inch

Bolt, 5/16 x 1 inch

Flange nuts, 5/16 inch

Installing the anti-scalp roller and

bracket

Mounting plate

Hex socket screw, 3/8 x 1-1/4 inch

Flange nuts, 3/8 inch

Installing the mounting plate

Pulley assembly 1 Installing the pulley assembly

Belt cover

Belt

Installing the belt cover and Belt

Before Installation

Prepare the Mower

Perform the following procedure to prepare the mower for

attaching the blower and finishing kit.

1. Disengage the PTO, move the motion control levers to

the neutral locked position and set the parking brake.

2. Stop the engine, remove the key, and wait for all

moving parts to stop before leaving the operating

position.

3. Clean the mower of any debris on the deck or rear of

mower to ease installation.

Summary of content (4 pages)

PAGE 1
Form No. 3352-634 48in TURBO FORCE Mower Finishing Kit Z400 Twin Soft Bagger Model No. 78511 Installation Instructions Setup Important These instructions are for Z400 machines only. Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts Note: Use the chart below to verify all parts have been shipped. Step Description 1 No parts needed 2 3 4 5 Qty.
PAGE 2
Installation Step Step 1 2 Parts needed for this step: • 1 Rear hinge bracket No Parts needed for this step. • 1 Hex socket screw, 3/8 x 1-1/4 inch Removing the Existing Belt Cover • Flange nut, 3/8 inch • 2 Bolts, 5/16 x 1 inch Note: Clean the area around the belt cover before removing. • 2 Flange nuts, 5/16 inch 1. Unlatch and remove the right belt cover (Fig. 1). Installing the New Bracket and Anti-Scalp Roller 2. Store the right belt cover for later use.
PAGE 3
Step 3 Step 4 Parts needed for this step: Parts needed for this step: • 1 Mounting plate • 1 Pulley assembly • 2 Hex socket head, 3/8 x 1-1/4 inch Installing the Pulley Assembly • 2 Flange nuts, 3/8 inch 1. Remove the existing pulley bolts from the existing mower deck pulley (Fig. 4). Installing the Mounting Plate 1. Move the grass deflector into the upright position. Note: When the mower is switched to bagging leave the grass deflector on the machine.
PAGE 4
Important Torque the bolts to 23 ft-lb ± 2 ft-lb (31 N⋅m ± 3 N⋅m). Do not over tighten. Step 5 Parts needed for this step: • 1 Belt cover • 1 Belt Installing the Belt Cover 1. Install the new belt cover over the pulley assembly and secure the latches (Fig. 5). 2 3 1 m–7803 Figure 5 1. Pulley assembly 2. Belt cover 3. Latch 2. Refer to the Operators Manual for installing the belt.