Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78520

FormNo.3358-424RevA

ChuteGateKit

34inand40inMowerDecksforZ300SeriesZMasterRiding

Mowers

ModelNo.78520

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaof

potentialdanger.Replaceanydecalthatisdamagedorlost.

108-4102

1.Operatordischargecontrol3.Closed

2.Open4.ReadtheOperator’s

Manual.

108-7250

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.Toro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

Summary of content (8 pages)

PAGE 1
Form No. 3358-424 Rev A Chute Gate Kit 34in and 40in Mower Decks for Z300 Series Z Master Riding Mowers Model No. 78520 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 108-4102 108-7250 1. Operator discharge control 3. Closed 2. Open 4. Read the Operator’s Manual.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty. Use 1 No parts required – Remove the existing side discharge chute. 2 Side discharge chute Bolt, (5/16 x 7–1/2 inches) Locknut, (5/16 inch) Plastic spacer Spring 1 1 1 1 1 Install the side discharge chute with gate. Handle assembly 1 Install the handle to the machine. Plastic cable ties Adhesive back mount 2 2 Secure the cables.
PAGE 3
2 Installing the Side Discharge Chute with Gate Parts needed for this procedure: 1 Side discharge chute 1 Bolt, (5/16 x 7–1/2 inches) 1 Locknut, (5/16 inch) 1 Plastic spacer 1 Spring Procedure An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury. Also, contact with the blade could occur. Figure 1 1. Bolt 2. Grass Deflector 3. Spring 5. Locknut 6. Spring installed 7.
PAGE 4
Figure 2 1. Grass Deflector 2. Spacer 3. Spring 4. Locknut 5. End of the spring is installed behind the deck edge 6. Spring installed 7. Bolt Figure 3 1. Fuel tank 2. Tank bracket 3. Washer 3 4. Bottom bolt 5. Locknut 6. Carriage bolt 4. Install the handle where the tank bracket was with the previously removed nuts and bolts (Figure 3). 5. Rotate the tank into the handle/bracket and secure the bottom with the previously removed washer and bolt (Figure 3).
PAGE 5
Figure 6 1. Plastic cable tie 3. Plastic mount 2. Ensure the cables do not get pinched or kinked here Figure 5 1. Handle 2. Washer 3. Bottom bolt 5 4 Installing the Decal for International Mowers Only Securing the Cables Parts needed for this procedure: 2 Plastic cable ties 2 Adhesive back mount Parts needed for this procedure: 1 International decal Procedure Procedure Secure the cables to the mower deck to ensure the cables do not interfere with the rear tires.
PAGE 6
Operation Using the Chute Gate The chute gate does not seal the discharge opening. Grass and objects maybe thrown in a bystander’s direction and result in serious injury. • Be aware of the mower discharge direction and do not point it at anyone. • Remove obstacles such as rocks, tree limbs, etc. from the mowing area. • Never put your hands or feet under the mower or discharge area. • Never try to clear the discharge area or mower blades unless the engine is off and the key is removed. Figure 7 1.
PAGE 7
Figure 8 1. Chute gate open 2. Chute gate at 45 degree angle 3.
PAGE 8