Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78574

FormNo.3407-158RevB

48in,52inor60inE-ZVac

™

BlowerandDriveKit

2016andAfterGrandstand

Mower

ModelNo.78574—SerialNo.400010798andUp

ModelNo.78575—SerialNo.400010798andUp

ModelNo.78576—SerialNo.400010798andUp

InstallationInstructions

WARNING

CALIFORNIA

Proposition65Warning

ThisproductcontainsachemicalorchemicalsknowntotheStateofCaliforniato

causecancer,birthdefects,orreproductiveharm.

Note:InstallthiskittousewiththeE-ZVacTwinBagger;refertotheOperator’sManualforthebaggerforsafety,operation,

andmaintenanceprocedures.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3407-158*B

Summary of content (8 pages)

PAGE 1
Form No. 3407-158 Rev B 48in, 52in or 60in E-Z Vac™ Blower and Drive Kit 2016 and After Grandstand® Mower Model No. 78574—Serial No. 400010798 and Up Model No. 78575—Serial No. 400010798 and Up Model No. 78576—Serial No. 400010798 and Up Installation Instructions WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm.
PAGE 2
Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal136-4087 136-4087 1. Warning—read the Operator’s Manual. 4. Cutting/dismemberment hazard, impeller—keep away from moving parts; keep all guards and covers in place. 2. Warning—wear hearing protection. 5.
PAGE 3
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 3 4 Description Qty. No parts required – Blower mount Bolt (1/2 x 1-1/2 inches) Lock washer Nut (1/2 inch) Bolt (3/8 x 1-1/4 inches) Nut (3/8 inch) Carriage bolt (3/8 x 1-1/4 inches) Carriage bolt (3/8 x 1 inch) Idler assembly Pulley assembly Blower assembly Belt Belt cover Knob 1 1 1 1 1 1 1 1 1 1 1 1 1 1 3 Use Prepare the machine. Install the pulley and idler assemblies.
PAGE 4
Note: Determine the left and right sides of the machine from the normal operating position. 1 Preparing the Machine No Parts Required Procedure Perform the following procedure to prepare the machine for attaching the blower and finishing kit. 1. Disengage the PTO, move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. g037552 Figure 1 2. Shut off the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 1.
PAGE 5
2. Remove the nuts from the spindle in the right deck pulley and use them to attach the pulley assembly to the deck pulley (Figure 3). 3 Note: You may need to remove the mower belt to relieve the tension off the deck pulley when you install the pulley assembly. Refer to the Operator’s Manual for the machine.
PAGE 6
4 Installing the Blower Assembly, Belt, and Belt Cover Parts needed for this procedure: 1 Blower assembly 1 Belt 1 Belt cover 1 Knob Procedure Refer to the bagger Operator’s Manual for the correct procedure to install the blower assembly, belt, and belt covers. g037508 Figure 5 1. Carriage bolt (3/8 x 1-1/4 inches) 3. Carriage bolt (3/8 x 1 inch) 2. Idler assembly 4.
PAGE 7
Notes:
PAGE 8
The Toro Warranty Landscape Contractor Equipment (LCE) A Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Products listed below if defective in materials or workmanship. Instructions for Obtaining Warranty Service If you think that your Toro Product contains a defect in materials or workmanship, follow this procedure: 1.