Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78576

FormNo.3435-383RevA

48in,52in,or60inE-ZVac

™

BlowerandDriveKit

2016andAfterGrandstand

Mower

ModelNo.78574—SerialNo.403300000andUp

ModelNo.78575—SerialNo.403300000andUp

ModelNo.78576—SerialNo.403300000andUp

InstallationInstructions

Note:InstallthiskittousewiththeE-ZVacTwinBagger;refertotheOperator’sManualforthebagger

forsafety,operation,andmaintenanceprocedures.

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyarea

ofpotentialdanger.Replaceanydecalthatisdamagedormissing.

decal136-4087

136-4087

1.Warning—readtheOperator’sManual.4.Cutting/dismembermenthazardofhand,impeller—stayaway

frommovingparts;keepallguardsandshieldsinplace.

2.Warning—wearhearingprotection.

5.Cutting/dismembermenthazardofhand,impeller—disengage

thePTO,removethekey,andwaitforallmovingpartstostop.

3.Thrownobjecthazard—donotoperatethemachinewithout

thecollectionsysteminstalledandlatched.

6.Warning;lossoftractionhazard—donotoperatewithonlythe

counterbalanceweightsinstalled;donotoperatewithonlythe

E-ZVacinstalled;onlyoperatewithboththeE-ZVacand

counterbalanceweightsinstalled.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA

AllRightsReserved

*3435-383*A

Summary of content (8 pages)

PAGE 1
Form No. 3435-383 Rev A 48in, 52in, or 60in E-Z Vac™ Blower and Drive Kit 2016 and After Grandstand® Mower Model No. 78574—Serial No. 403300000 and Up Model No. 78575—Serial No. 403300000 and Up Model No. 78576—Serial No. 403300000 and Up Installation Instructions Note: Install this kit to use with the E-Z Vac Twin Bagger; refer to the Operator’s Manual for the bagger for safety, operation, and maintenance procedures.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Qty. Use No parts required – Prepare the machine. No parts required – Remove the discharge chute and belt cover.
PAGE 3
Note: Determine the left and right sides of the machine from the normal operating position. 1 Preparing the Machine No Parts Required Procedure Perform the following procedure to prepare the machine for attaching the blower and finishing kit. 1. g037552 Disengage the PTO, move the motion-control levers to the NEUTRAL-LOCK position, and set the parking brake. Figure 1 1. Discharge chute 4. Spring 2.
PAGE 4
3 Installing the Pulley and Idler Assemblies For Machines with a Cast-Iron Spindle g194670 Figure 3 Parts needed for this procedure: 1. Nut (3/8 inch) 5. Bolt (1/2 x 1-1/2 inches) Bolt (1/2 x 1-1/2 inches) 2. Blower mount 3. Bolt (3/8 x 1-1/4 inches) 6. Lock washer 7. Nut (1/2 inch) 1 Lock washer 4.
PAGE 5
2. Remove the nuts from the spindle in the right deck pulley and use them to attach the pulley assembly to the deck pulley (Figure 3). Note: You may need to remove the mower belt to relieve the tension off the deck pulley when you install the pulley assembly. Refer to the Operator’s Manual for the machine. g037507 Figure 4 g037508 1. Nut 3. Spindle Figure 5 2. Pulley assembly 3.
PAGE 6
2. 4 Insert the pulley-plate mount studs into the holes in the sheave (Figure 7). Installing the Pulley Assembly and Belt For Machines with an Aluminum Spindle Parts needed for this procedure: 1 Pulley assembly 1 Pulley-plate mount 3 Flange nut (3/8 inch) Procedure 1. Remove the top nut, washer, and sheave from the spindle (Figure 6). g302390 Figure 7 Note: Note the orientation of the sheave when you remove it from the spindle to ensure that you install it properly later in the process. 1.
PAGE 7
4. 6. Install the sheave assembly to the spindle using the washer and top nut (Figure 9). Align the new pulley assembly so that the openings fit over the nuts (Figure 10). g302411 Figure 10 1. Pulley assembly 7. g302413 3. Sheave assembly 2. Washer 4. Spindle 5. Turn the pulley to lock it into position (Figure 11). Note: If the pulley does not turn, loosen the Figure 9 1. Top nut 2. Nuts nuts more to raise the nuts and allow the pulley to lock into position.
PAGE 8
5 Installing the Blower Assembly, Belt, and Belt Cover Parts needed for this procedure: 1 Blower assembly 1 Belt 1 Belt cover 1 Knob Procedure Refer to the bagger Operator’s Manual for the correct procedure to install the blower assembly, belt, and belt covers.