Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 78584

FormNo.3372-957RevB

ZStand

Kit

ZMaster

RidingMowerwith72inDeck

ModelNo.117-0354

ModelNo.121-4811

ModelNo.78584

InstallationInstructions

Safety

SafetyandInstructionalDecals

Safetydecalsandinstructionsareeasilyvisibletotheoperatorandarelocatednearanyareaofpotential

danger.Replaceanydecalthatisdamagedorlost.

107-3969

1.Warning—readtheOperator'sManual.

2.Crushinghazard,mower—engagetheparkingbrake,stop

theengine,andremovetheignitionkeybeforeworking

underthemower.

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3372-957*B

Summary of content (8 pages)

PAGE 1
Form No. 3372-957 Rev B Z Stand® Kit Z Master® Riding Mower with 72in Deck Model No. 117-0354 Model No. 121-4811 Model No. 78584 Installation Instructions Safety Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 107-3969 1. Warning—read the Operator's Manual. 2.
PAGE 2
Installation Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 Description Qty.
PAGE 3
1 2 Assembling the Z Stand® Hub Installing the Z Stand Hub Parts needed for this procedure: Parts needed for this procedure: 1 Z Stand hub 1 Latch bracket 1 Bolt (3/8 x 1-1/2 inches) 1 Flange nut (3/8 inch) Procedure 1. Park on a level surface, disengage the PTO, set the parking brake, remove the key and chock or block the drive wheels. 6 Carriage bolt (3/8 x 1-1/4 inches) (72 inch machines) 6 Flange nut (3/8 inch) (72 inch machines) 1 Bracket 1 Angle bracket (72 inch machines) 3.
PAGE 4
3 Installing the Z Stand Bracket Parts needed for this procedure: 2 Carriage bolt (3/8 x 1-1/4 inches) 2 Flange nut (3/8 inch) 1 Bolt (1/4 x 3/4 inches) 1 Locknut (1/4 inch) 1 Bracket pin 1 Lanyard 1 Cradle bracket Procedure Note: Ensure the grass deflector is installed in the lower holes in the mower deck brackets. 1. Place the Z Stand cradle bracket onto the left front frame as shown in Figure 4. Figure 2 1. Carriage bolt (3/8 x 1-1/4 inches) 5.
PAGE 5
Figure 5 Figure 4 1. Carriage bolts (3/8 x 1-1/4 inches) 6. Lanyard 2. Frame (48, 52 and 60 inch machines) 7. Nut (1/4 inch) 3. Cradle bracket 8. Bolt (1/4 x 3/4 inches) 1. Clevis pin 4. Hairpin cotter pin 2. Pivot pin 5. Foot 3. Outer tube 3. Place a thrust washer onto the pivot pin (Figure 6). 4. Flange nut (3/8 inch) 9. Correct hole for 48 and 52 inch mowers 5. Frame (72 inch machines) 10. Correct hole for 60 and 72 inch mowers 4. Insert the pivot pin into the Z Stand hub.
PAGE 6
Operation 5 Using the Z Stand® Installing the Foot Pedal (Machines with 48, 52 and 60 inch Mower Decks) The Z Stand® raises the front end of the machine to allow you to clean the mower and remove the blades. WARNING The machine could fall onto someone and cause serious injury or death. Parts needed for this procedure: 1 • Use extreme caution when operating the machine on the Z Stand®. Foot pedal • Use only for cleaning the mower and removing the blades. Procedure 1.
PAGE 7
5. Align the holes and install the clevis pin and hairpin cotter pin. Figure 9 1. Z Stand (Positioned in slot) Figure 10 3. Latch resting on pivot tab 2. Crack in side walk or turf 1. Z Stand 3. Locked position 2. Latch 4. Unlocked position 3. Start the engine and place it at half throttle. Disengage the parking brake. 6. Set the foot of stand on the ground and rest the latch on the pivot tab (Figure 9). 4. Slowly drive backwards off of the stand. 7. Start the engine and put it at half throttle.
PAGE 8