Form No. 3375-597 Rev A Z Master® Professional 6000 Series Riding Mower with 60in or 72in TURBO FORCE® Side Discharge Mower Model No. 74926—Serial No. 313000001 and Up Model No. 74928—Serial No. 313000001 and Up Model No. 74930—Serial No. 313000001 and Up Model No. 78926—Serial No. 313000001 and Up Model No. 78928—Serial No. 313000001 and Up g019887 Register at www.Toro.com.
Whenever you need service, genuine Toro parts, or additional information, contact an Authorized Service Dealer or Toro Customer Service and have the model and serial numbers of your product ready. Figure 1 identifies the location of the model and serial numbers on the product. Write the numbers in the space provided. WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.
Contents Jump Starting the Machine.......................................42 Drive System Maintenance .........................................44 Checking the Seat Belt.............................................44 Checking the Rollover Protection System (ROPS) Knobs...............................................................44 Adjusting the Tracking ............................................44 Checking the Tire Pressure ......................................45 Checking the Wheel Lug Nuts ............
Operation Safety • Lightning can cause severe injury or death. If lightning Improper use or maintenance by the operator or owner can result in injury. To reduce the potential for injury, comply with these safety instructions and always pay attention to the safety alert symbol, which means CAUTION, WARNING, or DANGER-“personal safety instruction." Failure to comply with the instruction may result in personal injury or death.
Safe handling of fuels • Use care when checking blades. Wrap the blade(s) or wear gloves, and use caution when servicing them. Only replace blades. Never straighten or weld them. • To avoid personal injury or property damage, use extreme care in handling gasoline. Gasoline is extremely flammable and the vapors are explosive. • Keep hands and feet away from moving parts. If possible, do not make adjustments with the engine running.
Slope Indicator G011841 Figure 3 This page may be copied for personal use. 1. The maximum slope you can safely operate the machine on is 15 degrees. Use the slope chart to determine the degree of slope of hills before operating. Do not operate this machine on a slope greater than 15 degrees. Fold along the appropriate line to match the recommended slope. 2. Align this edge with a vertical surface, a tree, building, fence pole, etc. 3. Example of how to compare slope with folded edge.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 68-8340 1-403005 98-5954 103-2076 54-9220 58-6520 1.
110-2067 110-2068 1. Read the Operator's Manual. 107-2102 114-4466 109-7232 8 1. Main, 25A 3. Charge, 25A 2. PTO, 10A 4.
116-0205 115-7445 1. Grease pulleys and spindles 2. Maintenance interval—50 hours 116-0211 116-0090 116-0752 116-0157 1. Latch 9 2.
116-1654 116-4858 116-1716 1. Fuel 2. Empty 3. Half 4. Full 5. Battery 6. Hour meter 7. PTO 116-5944 8. Parking brake 9. Neutral 10. Operator presence switch 116-2643 Battery Symbols Some or all of these symbols are on your battery 1. Explosion hazard 6. Keep bystanders a safe distance from the battery. 2. No fire, open flame, or smoking. 7. Wear eye protection; explosive gases can cause blindness and other injuries 3. Caustic liquid/chemical burn hazard 4. Wear eye protection 8.
120–5899 1. PTO (Power Take-off) 3. Continuous variable setting 2. Slow 4.
Hour Meter Product Overview The hour meter records the number of hours the engine has operated. It operates when the engine is running. Use these times for scheduling regular maintenance (Figure 6). Fuel Gauge The fuel gauge is located with the hour meter and the bars light up when the ignition switch is on (Figure 6). The indicator light appears when the fuel level is low (approximately one gallon remaining in the fuel tank).
Ignition Switch Length: This switch is used to start the mower engine and has three positions: Start, Run and Off. Motion Control Levers The motion control levers are used to drive the machine forward, reverse, and turn either direction. The neutral lock position is used with the safety interlock system to engage and to determine neutral position. Close the fuel shut-off valve (under the seat) when transporting or storing the mower.
Operation DANGER In certain conditions during fueling, static electricity can be released causing a spark which can ignite the gasoline vapors. A fire or explosion from gasoline can burn you and others and can damage property. • Always place gasoline containers on the ground away from your vehicle before filling.
Filling the Fuel Tank Breaking In a New Machine Note: Do not fill the fuel tank completely full. Fill the fuel tank to the bottom of the filler neck. The empty space in the tank allows the gasoline to expand. New engines take time to develop full power. Mower decks and drive systems have higher friction when new, placing additional load on the engine. Allow 40 to 50 hours of break-in time for new machines to develop full power and best performance. 1. Park the machine on level ground. 2.
DANGER Operating on wet grass or steep slopes can cause sliding and loss of control. Wheels dropping over edges can cause rollovers, which may result in serious injury, death or drowning. There is no rollover protection when the roll bar is down. Always keep the roll bar in the fully raised and locked position and use the seat belt. Read and follow the rollover protection instructions and warnings. To avoid loss of control and possibility of rollover: • Do not operate near drop-offs or near water.
Operating the Mower Blade Control Switch (PTO) The use of protective equipment for eyes, ears, feet and head is recommended. 1 2 The blade control switch (PTO) starts and stops the mower blades and any powered attachments. Engaging the Blade Control Switch (PTO) G009027 Figure 10 1. Wear safety glasses Note: Engaging the blade control switch (PTO) with the throttle position at half or less will cause excessive wear to the drive belts. 2.
Operating the Ignition Switch Starting and Stopping the Engine 1. Turn the ignition key to the Start position (Figure 16). When the engines starts, release the key. Starting the Engine Important: Do not engage starter for more than 5 seconds at a time. If the engine fails to start allow a 15 second cool-down period between attempts. Failure to follow these instructions can burn out the starter motor. 1. Raise the ROPS up and lock into place, sit on the seat and fasten the seat belt. 2.
RT ST A N RU P ST O G008947 Figure 19 1. Off 2. Run 3. Start Stopping the Engine CAUTION Children or bystanders may be injured if they move or attempt to operate the machine while it is unattended. Always remove the ignition key and set the parking brake when leaving the machine unattended, even if just for a few minutes. g017007 Figure 20 Let the engine idle at slow throttle (turtle) for 60 seconds before turning the ignition switch off.
• The blade control switch (PTO) is disengaged. • The motion control levers are in the neutral locked 5. Sitting on the seat, disengage the parking brake, move the blade control switch (PTO) to off and move the motion control levers to neutral lock position. Try starting the engine; the engine should not crank.
Driving Forward Note: The engine will kill if the traction control levers are moved with the parking brake engaged. To stop, pull the motion control levers to the neutral position. 1. Release the parking brake; refer to Releasing the Parking Brake in Operation. 2. Move the levers to the center, unlocked position. 3. To go forward, slowly push the motion control levers forward (Figure 23).
Adjusting the Height-of-Cut Pin The height-of-cut is adjusted from 1 to 5-1/2 inches (25 to 140 mm) in 1/4 inch (6 mm) increments by relocating the clevis pin into different hole locations. 1. Move the transport lock to the lock position. 2. Push on the deck lift pedal with your foot and raise the mower deck to the transport position (also the 5-1/2 inch (140 mm) cutting height position) (Figure 26). 3. To adjust, rotate the pin 90 degrees and remove the pin from the height-of-cut bracket (Figure 26). 4.
Adjusting the Flow Baffle Cam Locks This procedure is applicable only to machines with the flow baffle locks. Certain models will have nuts and bolts in-place of the flow baffle locks and can be adjusted the same. The mower discharge flow can be adjusted for different types of mowing conditions. Position the cam locks and baffle to give the best quality of cut. 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. Figure 27 1.
Position A This is the full rear position. The suggested use for this position is a follows. • • • • Use for short, light grass mowing conditions. Use in dry conditions. For smaller grass clippings. Propels grass clippings farther away from the mower. Figure 33 Positioning the Seat Figure 31 The seat can move forward and backward. Position the seat where you have the best control of the machine and are most comfortable. Position B To adjust, move the lever sideways to unlock seat (Figure 34).
Changing the Seat Suspension 2. Rotate the release valve levers vertically to push the machine. This allows hydraulic oil to by-pass the pump enabling the wheels to turn (Figure 37). The seat is adjustable to provide a smooth and comfortable ride. Position the seat where you are most comfortable. 3. Disengage parking brake before pushing. To adjust it, turn the knob in front either direction to provide the best comfort (Figure 36). g019768 1 Figure 36 1.
Transporting Machines Loading Machines Use a heavy-duty trailer or truck to transport the machine. Ensure that the trailer or truck has all necessary brakes, lighting, and marking as required by law. Please carefully read all the safety instructions. Knowing this information could help you, your family, pets or bystanders avoid injury. Use extreme caution when loading units on trailers or trucks.
Figure 39 1. Trailer 3. Not greater than 15 degrees 2. Full width ramp 4.
Operating Tips cutting height higher than usual and cut the grass at this setting. Then cut the grass again using the lower, normal setting. Fast Throttle Setting When Stopping For best mowing and maximum air circulation, operate the engine at the fast throttle position. Air is required to thoroughly cut grass clippings, so do not set the height-of-cut so low as to totally surround the mower by uncut grass.
Maintenance Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 100 hours • • • • After the first 250 hours • Change the hydraulic filters and hydraulic oil when using any type of oil. Before each use or daily • • • • • • • • Check the safety system. Check the engine oil level. Check the seat belt. Check the rollover protection system (ROPS) knobs. Clean the engine screen and the oil cooler. Check and clean the hydraulic unit shrouds.
CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders. Remove the key from the ignition before you do any maintenance. Lubrication Greasing and Lubrication Grease more frequently when operating conditions are extremely dusty or sandy. Grease Type: No. 2 general purpose lithium base or molybdenum base grease How to Grease G017050 Figure 41 1.
G009029 Figure 44 Figure 42 5. Grease the drive belt idler arm (Figure 42). Figure 43 6. Remove the dust cap and adjust the caster pivots. Keep the dust cap off until greasing is done. Refer to Adjusting the Caster Pivot Bearing in Maintenance. 7. Remove the hex plug. Thread a grease zerk into the hole. 8. Pump grease into the zerk until it oozes out around the top bearing. 9. Remove the grease zerk in the hole. Install the hex plug and dust cap (Figure 44).
Lubricate Caster Wheel Hubs 14. Service Interval: Yearly 1. Stop the engine, wait for all moving parts to stop, and remove the key. Engage the parking brake. Important: To prevent seal and bearing damage, check the bearing adjustment often. Spin the caster tire. The tire should not spin freely (more than 1 or 2 revolutions) or have any side play. If the wheel spins freely, adjust torque on spacer nut until there is a slight amount of drag. Reapply thread locking adhesive. Figure 45 1.
Engine Maintenance 8. Gently slide the primary filter out of the air cleaner body (Figure 47). Note: Avoid knocking the filter into the side of the body. WARNING Contact with hot surfaces may cause personal injury. 9. Remove the inner filter only if you intend to replace it. Important: Never attempt to clean the inner filter. If the safety filter is dirty, then the primary filter is damaged. Replace both filters.
Servicing the Engine Oil 2. If the inner filter is being replaced, carefully slide it into the filter body (Figure 47). Oil Type: Detergent oil (API service class SJ or higher) 3. Carefully slide the primary filter over the inner filter (Figure 47). Oil Capacity: with a filter change, 58 ounces (1.7 L); with no filter change, 48 ounces (1.4 L) Note: Ensure that the primary filter is fully seated by pushing on its outer rim while installing it. Viscosity: See the table below.
Changing the Engine Oil Service Interval: Every 100 hours (more often in dirty or dusty conditions) Note: Dispose of the used oil at a recycling center. 1. Park the machine so that the rear is slightly lower than the front to ensure the oil drains completely. G008804 1 2 2. Disengage the PTO, move the motion control levers to the neutral locked position and set the parking brake. 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position (Figure 50).
4. Slowly pour approximately 80% of the specified oil into the filler tube and slowly add the additional oil to bring it to the Full mark (Figure 51). 1 2 G008804 3 5 1 2 3 4 4 6 5 6 G008796 Figure 51 5. Start the engine and drive to a flat area. Check the oil level again. Changing the Engine Oil Filter 3/4 G008748 Service Interval: Every 200 hours Figure 52 Note: Change the engine oil filter more frequently when operating conditions are extremely dusty or sandy.
Servicing the Spark Plug Service Interval: Every 200 hours—Check, clean and regap the spark plug. Make sure the air gap between the center and side electrodes is correct before installing the spark plug. Use a spark plug wrench for removing and installing the spark plug(s) and a gapping tool/feeler gauge to check and adjust the air gap. Install a new spark plug(s) if necessary. G008804 1 2 Type : Champion® XC12YC, Champion® Platinum3071 or equivalent Air Gap: 0.030 inch (0.
Checking the Spark Plug Important: Replace the spark plug(s) when it has: a black coating, worn electrodes, an oily film, cracks or reuse is questionable. If you see light brown or gray on the insulator, the engine is operating properly. A black coating on the insulator usually means the air cleaner is dirty. Set the gap to 0.030 inches (0.76 mm). 1 2 G008794 Figure 56 Installing the Spark Plug Tighten the spark plug(s) to 18-22 ft.-lb (24.4–29.8 N-m). 1 Figure 54 1.
Check Spark Arrester (if equipped) Fuel System Maintenance Service Interval: Every 50 hours WARNING WARNING Fuel system components are under high pressure. The use of improper components can result in system failure, gasoline leakage and possible explosion. Hot exhaust system components may ignite gasoline vapors even after the engine is stopped. Hot particles exhausted during engine operation may ignite flammable materials. Fire may result in personal injury or property damage.
Electrical System Maintenance 1 2 Servicing the Battery 3 Service Interval: Monthly WARNING CALIFORNIA Proposition 65 Warning Battery posts, terminals, and related accessories contain lead and lead compounds, chemicals known to the State of California to cause cancer and reproductive harm. Wash hands after handling. G008963 Figure 58 1. Fuel filter 2. Hose clamp 3. Fuel line 6. Squeeze the ends of the hose clamps together and slide them away from the filter (Figure 58).
Installing the Battery WARNING 1. Position battery in the tray with the terminal posts opposite from the hydraulic tank (Figure 59). Incorrect battery cable routing could damage the machine and cables causing sparks. Sparks can cause the battery gasses to explode, resulting in personal injury. 2. First, install the positive (red) battery cable to positive (+) battery terminal. 3. Then install the negative (black) battery cable and ground wire to the negative (-) battery terminal.
Servicing the Fuses The electrical system is protected by fuses. It requires no maintenance, however, if a fuse blows check the component/circuit for a malfunction or short. 1. The fuses are located on right hand console next to the seat (Figure 61). 2. To replace the fuses, pull out on the fuse to remove it. 3. Install a new fuse (Figure 61). Figure 60 1. Positive Battery Post 3. Red (+) Charger Lead 2. Negative Battery Post 4. Black (-) Charger Lead Figure 61 1. Optional accesory-15 amp 4.
2. Make sure the booster battery is a good and fully charged lead acid battery at 12.6 volts or greater. Use properly sized jumper cables with short lengths to reduce voltage drop between systems. Make sure the cables are color coded or labeled for the correct polarity. 4. Connect the other end of the positive cable to the positive terminal of the booster battery. 5. Connect the black negative (–) cable to the other terminal (negative) of the booster battery. 6.
Drive System Maintenance Checking the Seat Belt Service Interval: Before each use or daily Visually inspect seat belt for wear, cuts, and proper operation of retractor and buckle. Replace before operating if damaged. Checking the Rollover Protection System (ROPS) Knobs Service Interval: Before each use or daily WARNING To avoid injury or death from rollover: keep the roll bar in the fully raised locked position and use the seat belt. Ensure that the rear part of the seat is secured with the seat latch.
Checking the Wheel Lug Nuts Check and torque the wheel lug nuts to 90-95 ft-lb (122-129 N-m). Checking the Wheel Hub Slotted Nut Service Interval: After the first 100 hours Every 500 hours See Figure 68 to determine which slotted nut has been installed on the unit. Figure 68 g019756 Figure 66 Left control lever shown 1. Control lever 1. Style A (black finish) 3. Style B (yellow zinc) 2. .03 inch (.76 mm) 4. .24 inch (6 mm) • Style A (black finish): 3.
6. Then tighten nut until the next set of slots line up with the cross hole in shaft. Do not loosen nut to align the slot. If required, tighten to the next set of slots. point where the clutch no longer engages consistently, the shim can be removed to extend the clutch life. 7. Install a new cotter pin. Note: Do Not use anti-seize on wheel hub. Adjusting the Caster Pivot Bearing Service Interval: Every 500 hours/Yearly (whichever comes first) 1.
to match the armature and needs to continue to match after the shim is removed to ensure proper brake torque. Figure 75 1. Feeler gauge Figure 73 1. Brake mounting bolt B. Using needle nose pliers, or by hand, take hold of the tab and remove the shim (Do Not discard the shim until proper clutch function has been confirmed). Figure 76 1. Feeler gauge • If the gap is less than 0.010 inch, then reinstall the shim and reference the Troubleshooting section.
Cooling System Maintenance Cleaning the Engine Screen and Engine Oil Cooler Service Interval: Before each use or daily Remove any build-up of grass, dirt or other debris from the oil cooler (Figure 77). G008804 Figure 78 1. Engine guard 4. Fan housing 2. Engine air intake screen 5. Screw 3. Bolt Figure 77 Check and Clean the Hydraulic Unit Shrouds Before each use remove any build-up of grass, dirt or other debris from the engine screen.
Brake Maintenance Adjusting the Parking Brake Service Interval: After the first 100 hours Every 500 hours thereafter Check to make sure brake is adjusted properly. This procedure must be followed after the first 100 hours or when a brake component has been removed or replaced. 1. Drive the machine onto a level surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 3.
Belt Maintenance Inspecting the Belts Service Interval: Every 50 hours Check the belts for squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn mower belt. Replace the mower belt if any of these conditions are evident. Replacing the Mower Belt Squealing when the belt is rotating, blades slipping when cutting grass, frayed belt edges, burn marks and cracks are signs of a worn mower belt.
Figure 83 1. Position the belt cover 3. Ensure the tab is under the metal catch 2. Slide belt cover under the side catches Replacing the Hydraulic Pump Drive Belt Figure 82 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease zerk 3. Spring loaded idler pulley 7. Belt guide 1. Disengage the PTO and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 4. Ratchet 3.
Controls System Maintenance Adjusting the Control Handle Position There are two height positions for the control levers; high and low. Remove the bolts to adjust the height for the operator. 1. Disengage the PTO, move the motion control levers to the neutral locked position, and set the parking brake. 2. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. 3. Loosen the bolts and flange nuts installed in the levers (Figure 85). Figure 84 1.
6. Run the unit at least 5 minutes with the drive levers at full forward speed to bring hydraulic oil up to operating temperature. Note: The motion control lever needs to be in neutral while making any necessary adjustments. 7. Bring the motion control levers into the neutral position. Adjust pump control rod lengths by rotating the double nuts on the rod in the appropriate direction until the wheels slightly creep in reverse (Figure 87).
Hydraulic System Maintenance Servicing the Hydraulic System Hydraulic Oil Type: Toro® HYPR-OIL™ 500 hydraulic oil or Mobil® 1 15W-50. Important: Use oil specified. Other fluids could cause system damage. Figure 88 RH Motion Control Shown Each Hydraulic System Oil Capacity: 52 ounces (1.5 l) per side with filter change 1. Torque the lock nut to 200 in-lb (16.7 ft-lb). Bolt must protrude past end of locknut after torque. Checking the Hydraulic Oil 2.
Replacing the Hydraulic Filters and Hydraulic Oil Service Interval: After the first 250 hours—Change the hydraulic filters and hydraulic oil when using any type of oil. Every 250 hours—Change the hydraulic filters and hydraulic oil when using Mobil® 1 oil (more often in dirty or dusty conditions). 3 Every 500 hours—Change the hydraulic filters and hydraulic oil when using Toro® HYPR-OIL™ 500 hydraulic oil (more often in dirty or dusty conditions).
Mower Deck Maintenance 1 Leveling the Mower Deck Setting Up the Machine Note: Ensure the mower deck is leveled before matching the height-of-cut (HOC). 1. Position mower on a flat surface. 2. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. 2 3. Stop the engine, remove the key, and wait for all moving parts to stop before leaving the operating position. G008968 4. Check tire pressure of the drive tires.
10. For mower decks shown in Figure 95, fine-tune the adjustment nut on the front deck lift assembly by turning it (Figure 95). 3 To increase the height, turn the adjustment nut clockwise; to decrease, turn counterclockwise. 1 3 4 2 2 1 2 1 G017027 Figure 93 3. Transport lock 1. Deck lift pedal 2. Height of cut pin 6. Insert the height adjustment pin into the 3 inch (7.6 cm) cutting height location. G012430 7. Release the transport lock and allow the deck to lower to the cutting height.
12. If the front deck links do not have enough adjustment to achieve accurate cut height , the single point adjustment can be utilized to gain more adjustment. 13. To adjust the single point system, loosen the two bolts at the bottom of the height of cut plate. Refer to Figure 97. g017036 Figure 98 1. Single point adjustment bolt 15. Tighten the two bolts at the bottom of the height of cut plate (Figure 97). Torque to 27-33 ft-lb (37-45 N-m).
Checking for Bent Blades Servicing the Cutting Blades 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake. Maintain sharp blades throughout the cutting season because sharp blades cut cleanly without tearing or shredding the grass blades. Tearing and shredding turns grass brown at the edges, which slows growth and increases the chance of disease. 2.
and continued safety conformance of the machine, use genuine Toro replacement blades. Replacement blades made by other manufacturers may result in non-conformance with safety standards. position, the blade is balanced and can be used. If the blade is not balanced, file some metal off the end of the sail area only (Figure 104). Repeat this procedure until the blade is balanced. 1. Hold the blade end using a rag or thickly-padded glove. 2.
Removing the Mower Deck Installing the Blades 1. Install the blade onto the spindle shaft (Figure 104). Before servicing or removing the mower deck, the spring loaded deck arms must be locked out. Important: The curved part of the blade must be pointing upward toward the inside of the mower to ensure proper cutting. WARNING 2. Install the spring disk and blade bolt. The spring disk cone must be installed toward the bolt head (Figure 104). Torque the blade bolt to 85-110 ft-lb (115-150 N-m).
Figure 106 1. Right stabilizer Figure 105 1. Clutch pulley 2. Mower belt 5. Square hole in the idler arm for the ratchet 6. Idler grease zerk 3. Spring loaded idler pulley 7. Belt guide 2. Deck strut (right side shown) 3. Remove the rear deck lift attachment shoulder bolt and nut. 4. Remove the front deck lift attachment shoulder bolt and nut. 4. Ratchet 7. Remove and retain the hardware on both sides of the deck as shown in Figure 106 or Figure 107. Figure 107 1. Right stabilizer 2.
Replacing the Grass Deflector Cleaning WARNING Cleaning Under the Mower An uncovered discharge opening could allow the lawn mower to throw objects in the operator's or bystander's direction and result in serious injury. Also, contact with the blade could occur. Service Interval: Before each use or daily 1. Disengage the blade control switch (PTO), move the motion control levers to the neutral locked position and set the parking brake.
Storage Cleaning and Storage 1. Disengage the power take off (blade control switch (PTO), set the parking brake, and turn the ignition key to Off. Remove the key. Stop the engine, allow it to cool, and drain the fuel tank; refer to Servicing the Fuel Tank in the Maintenance Section. D. Restart the engine and run it until it stops. E. Dispose of fuel properly. Recycle as per local codes. Important: Do not store stabilizer/conditioned fuel over 90 days. 2.
Troubleshooting Problem Starter does not crank Engine will not start, starts hard, or fails to keep running Possible Cause 1. Blade control switch (PTO) is engaged. 1. Move blade control switch (PTO) to disengaged. 2. Parking brake is not on. 3. Drive levers are not in neutral lock position. 4. Operator is not seated. 5. Battery is dead. 6. Electrical connections are corroded or loose. 7. Fuse is blown. 8. Relay or switch is defective. 2. Set the parking brake. 3.
Problem Machine does not drive. Abnormal vibration. Uneven cutting height. Possible Cause 1. By pass valves is not closed tight. 1. Tighten the by pass valves. 2. 3. 4. 5. 2. 3. 4. 5. Pump belt is worn, loose or broken. Pump belt is off a pulley. Broken or missing idler spring. Hydraulic oil level is low or too hot. 1. Install new cutting blade(s). 2. Blade mounting bolt is loose. 3. Engine mounting bolts are loose. 4. Loose engine pulley, idler pulley, or blade pulley. 5. Engine pulley is damaged.
Problem Malfunction Indicator Light (MIL) comes on. Possible Cause Corrective Action 1. Engine is too hot. 1. Turn engine off and let it cool. 2. Old gas in the gas tank. 3. The fuel shut-off valve is not open completely. 4. Air cleaner is dirty. 2. Use new gas. 3. Open the fuel shut-off valve. 5. Battery is not charged. 6. Incorrect fuel filters used or dirty fuel filters. 7. Connections to sensors electronic control unit (ECU) and fuel injectors are not secured properly. 8.
- GND BK BK A C FUEL SENDER S B BU PK + PK PK 2 3 BN BN BN V BK BK U2 11 F4 GND 15A PK 7 HOUR METER 9 4 7 W PK 12 OR 10 T SW6 (BRAKE) 8 6 2 3 Y SW4 (NEUT_L) BN 8 B PTO CLUTCH TVS DIODE BK A BN 4 5 BK LTGR SW5 (NEUT_R) PTO (PTO SWITCH) SW2 F3 PK FUEL_SOLENOID NEUTRAL 1 OR SEAT 5 8 4 7 10A KEY_A 1 GN SW7 (SEAT) BN PK OR GY R OR R GY PK PK GY V SW1 (IGNITION) 2 5 1 3 B I S R 5 GN 2 OPTIONAL ACCESSORIES FUEL GROUND BRAKE Wire Diagram (Rev.
Notes: 69
Notes: 70
Notes: 71
The Toro Total Coverage Warranty Landscape Contractor Equipment (LCE) A Limited Warranty (see warranty periods below) Conditions and Products Covered This warranty includes the cost of parts and labor, but you must pay transportation costs. The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship.