Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 79031

FormNo.3377-677RevA

FrontWeightKit

TimeCutter

SeriesRidingMower

ModelNo.79031

InstallationInstructions

LooseParts

Usethechartbelowtoverifythatallpartshavebeenshipped.

Description

Qty.

Use

Bolt(3/8x1-1/4inches)

Locknut(3/8inch)

Weightmountingbracket,left

Weightmountingbracket,right1

Washers4

Weightholdingbracket1

Bolt(3/8x1inch)

Flatweight1

Suitcaseweight

Keyedcrossbar1

Installtheweight.

InstallingtheWeight

CAUTION

Theattachmentchangestheweightdistribution

ofthemachine.Operatingthemachinewithout

thefrontweightsmaycauseanunstablecondition

whichcouldresultinalossofcontrol.

Ensurethefrontweightsareproperlyinstalled

beforeoperatingthemachinewiththeattachment.

1.Parkthemachineonalevelsurface,removethekey

fromtheignitionswitch,engageparkingbrake,let

enginecoolanddisconnectthewirefromthespark

plug(s)beforeinstallingtheattachment.

2.Locatetheforwardboltsontheundersideoftheframe

(Figure1andFigure2).Removethetwobolts(3/8x1

inch)andtwolocknuts(3/8inch).Retainthelocknuts.

G014875

Figure1

1.Frontrightcaster(castor

forkandwheelnotshown

forclarity)

3.Bolt(3/8x1inch)

2.Forwardhole,rightside

4.Locknut(3/8inch)

8111LyndaleAvenueSouth

Bloomington,MN55420

Registeratwww.T oro.com.

OriginalInstructions(EN)

PrintedintheUSA.

AllRightsReserved

*3377-677*A

Summary of content (4 pages)

PAGE 1
Form No. 3377-677 Rev A Front Weight Kit TimeCutter® Series Riding Mower Model No. 79031 Installation Instructions Loose Parts Use the chart below to verify that all parts have been shipped. Description Use Qty. 4 4 1 1 4 1 2 1 1 1 Bolt (3/8 x 1-1/4 inches) Lock nut (3/8 inch) Weight mounting bracket, left Weight mounting bracket, right Washers Weight holding bracket Bolt (3/8 x 1 inch) Flat weight Suitcase weight Keyed cross bar Installing the Weight Install the weight.
PAGE 2
3 2 1 1 3 8 7 6 G014877 4 Figure 2 1. Locknut (3/8 inch) 4 G014876 5 3. Front left caster (castor fork and wheel not shown for clarity) 2. Forward hole, left side Figure 4 4. Bolt (3/8 x 1 inch) 3. Locate the left and right weight mounting brackets in loose parts. Start by installing the left bracket to the under side of the frame. 4. Secure the bracket to the frame using two bolts (3/8 x 1-1/4 inches), two washers and two lock nuts (3/8 inch) (Figure 3).
PAGE 3
6. Install the weight holding bracket to the mounting brackets (Figure 6). Align the inboard holes in the bracket with the mounting brackets installed previously. Make sure the bracket is centered on the frame. Secure with two bolts (3/8 x 1 inch) and two lock nuts (3/8 inch). 2 1 2 1 G014879 7. Install a flat weight to the holding bracket and move it rearward, flush with the bracket (Figure 7). 3 3 4 5 Figure 6 1. Locknut (3/8 inch) 4. Bolt (3/8 x 1 inch) 2. Weight holding bracket 5.
PAGE 4