Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 79195

FORM NO. 3319–481 Rev. A

MODEL NO. 79195

INSTALLATION

INSTRUCTIONS

 



 

!'& $"  )!'  &# $(  )#  %# %'$%*$)%&

$"  )!'  &# $(  )#  %# %'$%*$)%&

$"  )!'  &# $(  %# %'$%*$)%&

$"  )!'  &# $(  %# %'$%*$)%&

Loose Parts

Note: Use the chart below to identify parts used for assembly.

DESCRIPTION QTY. USE

Baffle–front

Baffle–discharge

Carriage bolt 5/16”–18 x 3/4” (19 mm)

Locknut 5/16”–18

Install front and discharge baffles

Kicker

Spacer

Bolt 5/16” 18 x 1” (25 mm)

Locknut 5/16”–18

Install kickers

Blade

Decal–Recycler



Install blades and decal

Summary of content (8 pages)

PAGE 1
FORM NO. 3319–481 Rev. A  MODEL NO. 79195 !'& $ " )!' $ " )!' $ " )!' $ " )!' INSTALLATION INSTRUCTIONS & # $( )# % # % '$%* $) %& & # $( )# % # % '$%* $) %& & # $( % # % '$%* $) %& & # $( % # % '$%* $) %& Loose Parts Note: Use the chart below to identify parts used for assembly. DESCRIPTION QTY.
PAGE 2
Installation Pre–Installation Install Discharge Baffle 1. Remove mower unit refer to: Operator’s Manual for instructions. 1. Locate discharge baffle mounting hole in front of mower. Remove and discard any existing hardware filling mounting hole. 2. Thoroughly clean the mower. All debris must be removed to ensure baffles will fit properly against mower. 2. Position discharge baffle in discharge opening. Engage pin on flange into rear right baffle (Fig. 2). 3.
PAGE 3
Installation Install Front Baffle 3. 1. Locate front baffle mounting holes in mower. Remove and discard any existing hardware filling mounting holes. 2. Place front baffle inside mower and align with mounting holes (Fig. 3). Right side of mower Place (4) 5/16-18 x 3/4” (19 mm) carriage bolts with heads on the inside of the ends and on top at the mounting brackets as shown (Fig. 3). Secure with 5/16” locknuts (Fig. 3). 3 4 4 3 4 1 2 4 2 Figure 3 1. Front baffle 2.
PAGE 4
Installation Install Kickers 4. 5. Locate kicker mounting holes in center and left chambers. Remove and discard any existing hardware filling kicker mounting holes. 6. Install kickers with 5/16–18 x 1” (26 mm) bolt, with head inside mower and spacer between kicker and mower. Secure with 5/16” lock nut on top of mower (Fig. 4). 7. Tighten all mounting hardware securely. Place kickers tight against mower baffle (Fig. 4). Left side of mower 4 4 1 1 3 2 3 2 5 5 Figure 4 1. Kicker 2.
PAGE 5
Installation Removing the Recycler Baffle 1 Note: 2 4 Only the right side baffle need be removed for side discharge mowing. 1. Thoroughly clean the mower. 2. Remove lock nuts and carriage bolts from front and flange on discharge baffle (Fig. 6). Lower baffle and slide out discharge opening to remove. 3 4 3. Install previously removed 5/16–3/4” (19 mm) carriage bolts and 5/16” lock nuts in open holes of mower for safety (Fig. 6). m–3137 Figure 6 1. Baffle right side 2. Flange pin 3.
PAGE 6
Installation Recycling Tips Selecting The Proper Height-Of-Cut Setting To Suit Conditions – Remove approximately one inch or no more that 1/3 of the grass blade when cutting. In exceptionally lush and dense grass you may have to raise your height-of-cut setting another notch or convert to side discharge or bagging operations. POTENTIAL HAZARD • Without the grass deflector or Recycler assembly mounted in place, you and others are exposed to blade contact and thrown debris.
PAGE 7
PAGE 8