Form No. 3329-278 Rev B 38I and 42I Twin Bagger TimeCutterR Z Attachment Model No. 79214—Serial No. 230000001 and Up Model No. 79215—Serial No.
Contents 1 Page Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety and Instruction Decals . . . . . . . . . . . . . . . . . 3 Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Loose Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Installing the Front Weight . . . . . . . . . . . . . . . . . . .
Safety Safety and Instruction Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 93-7320 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. Do not remove the bagger top when it is closed; open the bagger top and then remove it. 93-1122 93-7316 (International) 1.
Setup Note: Determine the left and right sides of the machine from the normal operating position. Loose Parts DESCRIPTION QTY.
2. Install the front weight to the bottom footrest frame with 2 bolts (3/8 x 2–1/4 inch), 4 washers (3/8 inch) and 2 nuts (3/8 inch) (Figure 3). 2 Note: Make sure the weight is installed as shown in Figure 3. 5 3 4 3. Install the footrest into the footrest frame while placing the rods in the same hole positions (Fig. 2). 2 4 1 1 2 m–6626 Figure 4 3 1. Quick attach bracket 2. Bolts, 3/8 x 1 inch 3.
Installing the Bagger Assembly 2. Install the bags by sliding the bag frame hooks onto the retaining brackets (Fig. 7). 1. Carefully lift the bagger top and slide it onto the quick attach bracket (Fig. 6). The bagger top is easier to install if two people work together. 1 1 2 2 m–6627 Figure 7 1. Bag frame hook m–6617 Figure 6 1. Bagger top 2. Retaining bracket 3. Lower the bagger top onto the bags. Then push down on both bag retainer handles until they lock on the bag frame (Fig. 8). 2.
1 2 5. Repeat steps 1 through 4 for the opposite blade. 3 2 1 5 m–6619 3 Figure 9 1. Grass deflector 2. Pivot rod 4 3. Nut m–6430 Figure 11 1. Sail area of blade 2. Blade 3. Curved washer 4. Insert the new pivot rod into the short stand-off on the deck. Secure the rear end of rod into the mower with a nut (3/8 inch) (Fig. 10). 2 Installing the Chute and Discharge Tube 4 1. Slide the chute into position with the rear hook around the deflector rod and the front latch aligned.
Removing the Bagger Warning An uncovered discharge opening could allow the lawn mower to throw objects in the operator’s or bystander’s direction and result in serious injury. Also, contact with the blade could occur. 1 3 Never operate the lawn mower unless you install a cover plate, a mulch plate, or a grass chute and catcher. 2 1. Push on the tab on the chute and pull the discharge tube free from the chute and grass catcher (Fig. 13) m–6616 2.
Important The grass deflector must be spring loaded in the down position. Lift the deflector up to test that it snaps to the full down position. Warning If you remove the spring-loaded bagger top when it is closed (in the down position), the top may suddenly fly open and you or someone else may be bruised, pinched, or injured in another way. 1 2 3 Always open (raise) the bagger top before you remove or install it on the quick-attach bracket. 4.
Cutting Technique 4. Install the bags by sliding the bag frame hooks onto the retaining brackets (Fig. 7). For best lawn appearance, be sure to slightly overlap the mower into the previously cut area. This helps reduce the load on the engine and reduces the chance of plugging the chute and discharge tube. 5. Lower the bagger top onto the bags. Then push down on both bag retainer handles until they lock on the bag frame (Fig. 8).
bagging system, mow the grass at a high height of cut, then lower the mower to your normal cutting height and repeat the bagging process. Caution As the bagger fills, extra weight is added to the back of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. Bagging Wet Grass Always try to cut grass when it is dry because your lawn will have a neat appearance. If you must cut wet grass, use the conventional side discharge feature of the mower.
Inspecting the Bagger Attachment Storing the Bagger Attachment 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment, page 12. Inspect the bagger attachment after the first 10 hours of operation, and monthly thereafter. 2. Inspect the bagger attachment for damage; refer to Inspecting the Bagger Attachment, page 12. 1. Check the chute, discharge tube, and the bagger top. Replace these parts if they are cracked or broken. 3. Make sure the grass bags are empty and thoroughly dry. 2.
Consumer TimeCutter The Toro Total Coverage Guarantee A Two-Year Full Warranty (Limited Warranty for Commercial Use) Conditions and Products Covered Owner Responsibilities The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair any Toro Product used for normal residential purposes* if defective in materials or workmanship.
