Form No. 3367-339 Rev C 42in Bagger 2011 and After TimeCutter® Z4000 Series Riding Mower Model No. 79334—Serial No. 311000001 and Up To register your product or download an Operator's Manual or Parts Catalog at no charge, go to www.Toro.com.
This manual uses 2 other words to highlight information. Important calls attention to special mechanical information and Note emphasizes general information worthy of special attention. Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely. Contents Introduction................................................................. 2 Safety .................
Towing Safety Safety • Do not attach towed equipment except at the hitch point. DANGER • Follow the attachment manufacturer's recommendation for weight limits for towed equipment and towing on slopes. Engines can become hot when they are operating. Severe burns can occur from contacting hot surfaces. • Never allow children or others in or on towed equipment. Allow engines, especially the muffler, to cool before touching.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. Do not remove the bagger top when it is closed; open the bagger top and then remove it.
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure 1 2 3 4 5 6 7 Description Use Qty.
2 1 1 3 Installing the Weight Parts needed for this procedure: 4 Bolt (3/8 x 1-1/4 inches) 4 Lock nut (3/8 inch) 1 Weight mounting bracket, left 1 Weight mounting bracket, right 4 Washers 1 Weight holding bracket 2 G014875 4 Figure 3 3. Bolt (3/8 x 1 inch) Bolt (3/8 x 1 inch) 1. Front right caster (castor fork and wheel not shown for clarity) 1 Flat weight 2. Forward hole, right side 4.
2 3 2 1 1 3 4 5 8 7 6 6 G014878 8 4 G014876 7 5 Figure 5 Figure 6 1. Locknut (3/8 inch), existing 5. Hole, existing in frame 2. Forward hole, left side 3. Front left caster (castor fork and wheel not shown for clarity) 6. Washer 7. Bolt (3/8 x 1-1/4 inches) 4. Locknut (3/8 inch), loose parts 8. Left mounting bracket 1. Front right caster (castor fork and wheel not shown for clarity) 5. Bolt (3/8 x 1-1/4 inches) 2. Forward hole, right side 6. Washer 3. Locknut (3/8 inch), existing 7.
6. Install the weight holding bracket to the mounting brackets (Figure 8). Align the inboard holes in the bracket with the mounting brackets installed previously. Make sure the bracket is centered on the frame. Secure with two bolts (3/8 x 1 inch) and two lock nuts (3/8 inch). 2 1 2 1 G014879 7. Install a flat weight to the holding bracket and move it rearward, flush with the bracket (Figure 9). 3 3 4 5 Figure 8 1. Locknut (3/8 inch) 4. Bolt (3/8 x 1 inch) 2. Weight holding bracket 5.
2 3 Installing the Engine Guard Installing the Bagger Frame Parts needed for this procedure: Parts needed for this procedure: 1 Engine guard 1 Bagger frame support bracket 4 Self tapping screw (5/16 x 3/4 inch) 1 Support spacer plate 2 Self tapping screw (5/16 x 3/4 inch) Procedure 2 Bolt (5/16 x 1 inch) Note: Certain models will have an engine guard already installed. If equipped, proceed to the next procedure.
G010578 1 1 5 2 2 G014884 Figure 12 1. Support bracket 3 2. Self tapping screws (5/16 x 3/4 inch) 4 Figure 14 3. Install the angled bagger bracket to the engine guard using two carriage bolts (5/16 x 3/4 inch) and two locknuts (5/16 inch). 1 1. Bagger frame (60 inch decks) 4. Hair pin 2. Clevis pin (1/2 x 2-1/4 inch) 5. Angle bracket 3. Support bracket, receiver 2 G014882 5. Install two support rods, one to each side of the bagger frame.
4 5 Assembling the Bagger Top Installing the Bagger Top Parts needed for this procedure: Parts needed for this procedure: 1 Bagger top 2 Grass Bag 1 Bagger screen 1 Upper bagger tube Procedure Procedure Turn the bagger top over. Install the screen as shown in Figure 16 so it slopes down toward the collection bags. Make sure the screens snap into place and the tabs engage the bagger top. 1. Install the bagger top to the bagger frame.
2. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 18). 6 1 Installing the Chute Parts needed for this procedure: 1 Chute Procedure 1. Angle the metal tab at the front of the chute into the slot in the bracket welded to the mower deck just in front of the cutoff (Figure 20). 2 4 1 3 3 G005672 Figure 18 1. Bag 3. Retaining bracket 2. Bagger frame 4. Bag frame hook 2 3. Lower the bagger top onto the bag (Figure 19).
7 Connecting with the Discharge Tube No Parts Required Procedure G015204 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 23). Figure 21 2 1 Note: Make sure the retaining hook on the chute is out of the way so the chute opening mounts flush to the deck. G010641 3. Secure the chute to the deck. Hook the flexible latch on the chute to the retaining clasp welded on the mower deck to the rear of the opening (Figure 22).
Operation 1 Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. • Never remove the discharge tube, bags, bagger top, or the chute while the engine is running.
Removing the Bagger reduce the load on the engine and reduces the chance of plugging the chute and discharge tube. CAUTION Bagging Speed Failing to remove the front bagger weights and operating the machine without the bagger attachment may cause an unstable condition which could result in a loss of control. • Always remove the front weights when removing the bagger attachment. • Never operate the machine without the bagger attachment and the front weights still installed.
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Inspect the bagger Before each use or daily Before storage • Clean the bagger • Inspect the bagger • Clean the bagger CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders.
If the blades are badly worn or damaged, install new blades. Refer to your mower or mower Operator's Manual for complete blade maintenance. Storage Caring for the Grass Bags 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment. Storing the Bagger Attachment Washing the grass bags is not recommended. 2. Inspect the bagger attachment for damage; refer to Inspecting the Bagger Attachment.
Notes: 18
Notes: 19
The Toro Total Coverage Warranty TimeCutter and TITAN Mowers Limited Warranty (see warranty periods below) Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to the original purchaser to repair the Toro Products listed below if defective in materials or workmanship.
