Use and Care Manual

ManualsBrandsToro ManualsLawn Mower BaggersTimeCutter Twin Bagger for 32 in. Deck

FormNo.3399-540RevA

32inBagger

Zero-Turn-RadiusRidingMower

ModelNo.79390—SerialNo.316000001andUp

Operator'sManual

Introduction

Readthisinformationcarefullytolearnhowtooperateand

maintainyourproductproperlyandtoavoidinjuryand

productdamage.Youareresponsibleforoperatingthe

productproperlyandsafely.

Wheneveryouneedservice,genuineparts,oradditional

information,contactanAuthorizedServiceDealeror

CustomerServiceandhavethemodelandserialnumbersof

yourproductready.Figure1identiesthelocationofthe

modelandserialnumbersontheproduct.Writethenumbers

inthespaceprovided.

Figure1

1.Modelandserialnumberlocation

ModelNo.

SerialNo.

Thismanualidentiespotentialhazardsandhassafety

messagesidentiedbythesafety-alertsymbol(Figure2),

whichsignalsahazardthatmaycauseseriousinjuryordeath

ifyoudonotfollowtherecommendedprecautions.

Figure2

1.Safety-alertsymbol

Thismanualuses2wordstohighlightinformation.

Importantcallsattentiontospecialmechanicalinformation

andNoteemphasizesgeneralinformationworthyofspecial

attention.

WARNING

CALIFORNIA

Proposition65Warning

Thisproductcontainsachemicalorchemicals

knowntotheStateofCaliforniatocausecancer,

birthdefects,orreproductiveharm.

Contents

Introduction..................................................................1

Safety...........................................................................2

TowingSafety.........................................................2

SafetyandInstructionalDecals.................................3

Setup............................................................................4

1InstallingtheWeight..............................................5

2InstallingtheAttachmentMount.............................7

3InstallingtheLatchRod........................................10

4AssemblingtheBaggerTop...................................11

5InstallingtheBaggerTop......................................11

6InstallingtheChute..............................................12

7ConnectingwiththeDischargeTube......................14

8InstallingtheDeckRing........................................14

9InstallingtheBlade...............................................15

Operation....................................................................16

EmptyingtheGrassBags.........................................16

ClearingObstructionsfromtheBagger.....................16

RemovingtheBagger..............................................17

UsingtheDrawBar................................................17

OperatingTips......................................................18

Maintenance.................................................................19

RecommendedMaintenanceSchedule(s)......................19

InspectingtheBaggerAttachment............................19

InspectingtheMowerBlades...................................19

CleaningtheBaggerAttachment..............................20

Storage........................................................................20

StoringtheBaggerAttachment.................................20

OriginalInstructions(EN)PrintedintheUSA

AllRightsReserved

*3399-540*A

Summary of content (20 pages)

PAGE 1
Form No. 3399-540 Rev A 32in Bagger Zero-Turn-Radius Riding Mower Model No. 79390—Serial No. 316000001 and Up Operator's Manual Introduction Read this information carefully to learn how to operate and maintain your product properly and to avoid injury and product damage. You are responsible for operating the product properly and safely.
PAGE 2
Safety • If you remove the grass catcher, be sure to install any discharge deflector or guard that might have been removed to install the grass catcher. Do not operate the mower without either the entire grass catcher or the grass deflector in place. DANGER Engines can become hot when they are operating. Severe burns can occur from contacting hot surfaces. • Stop the engine before removing the grass catcher or unclogging the chute.
PAGE 3
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. 109-6809 1. Crushing hazard of hand—do not remove the whole bagger from the machine; open the bagger top and then remove the bag(s) from the bagger. Do not remove the bagger top when it is closed; open the bagger top and then remove it. 131-4036 1. The maximum drawbar pull is 36 kg (80 lb). 2.
PAGE 4
Setup Loose Parts Use the chart below to verify that all parts have been shipped. Procedure Description Qty.
PAGE 5
2 1 1 3 Installing the Weight Parts needed for this procedure: 4 Bolt (3/8 x 1-1/4 inches) 4 Locknut (3/8 inch) 1 Weight mounting bracket, left 1 Weight mounting bracket, right 4 Washers 1 Weight bracket 2 G014875 4 Figure 3 3. Bolt (3/8 x 1 inch) Bolt (3/8 x 1 inch) 1. Front-right caster (castor fork and wheel not shown for clarity) 1 Flat weight 2. Front hole, right side 4.
PAGE 6
3 2 Note: For machines with a foot assist lift pedal, the washers are not used. 1 4 • For machines with a foot assist lift pedal, Remove the forward fasteners in the foot assist lift pedal bracket and secure the bracket using 2 bolts and 2 locknuts (Figure 7). 5 Note: Use 1 locknut from the loose parts and the other from 1 of the locknuts that you previously removed. 6 2 G014878 1 8 3 7 Figure 5 8 1. Locknut (3/8 inch), existing 5. Hole, existing in frame 2. Forward hole, left side 3.
PAGE 7
2 1 G014879 10. Secure the weights to the weight bracket with a keyed-cross bar (Figure 9). Install the bar and rotate it 90 degrees downward to lock it in place. 11. After you install all the weights and brackets, check that all the fasteners are tight. Tighten them as necessary. 3 Important: Whenever you remove the bagger attachment, remember to remove the front weights to return the proper stability to the machine. 4 2 5 Figure 8 1. Locknut (3/8 inch) 4. Bolt (3/8 x 1 inch) 2.
PAGE 8
g030494 Figure 10 2015 model shown 1. Stabilizer bracket Figure 12 3. Locknut (5/16 inch) 1. Self-tapping screw (5/16 x 3/4 inch) 2. Carriage bolt (5/16 x 3/4 inch) 2. Pivot frame 4. Attach the draw bar decal 1.3 cm (1/2 inch) to the left of the attachment mount (Figure 13). 2. Install the pivot frame to the machine frame as shown in Figure 11. Secure the pivot frame to the machine frame using 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch). Figure 13 1. Draw bar decal 5.
PAGE 9
For 2011 through 2014 Models Only Note: The stabilizer bracket is not used on 2011 through 2014 models. Note: For 2011 through 2014 models, the rear-engine guard is optional for this bagger. 1. Install the pivot frame to the machine frame as shown in Figure 15. Secure the pivot frame to the machine frame using 2 bolts (5/16 x 1 inch) and 2 locknuts (5/16 inch). 6 Figure 14 Left side shown 1. Pivot frame hole 4. Support rod 2. Washer 5. Keyed slot, existing 3. Hairpin cotter 6.
PAGE 10
2 3 1 4 g030499 6 5 Figure 18 Left side shown 2 1 g030497 Figure 16 1. Self-tapping screw (5/16 x 3/4 inch) 1. Pivot-frame hole 4. Support rod 2. Washer 5. Keyed slot (existing) 3. Hairpin cotter 6. Bent, flared end of support rod 2. Pivot frame 5. Insert the bent ends of the rod into the attachment mount as shown in Figure 18 and secure the end of each rod with a washer and hairpin cotter. 3. Attach the draw-bar decal 1.
PAGE 11
1 2 Figure 19 1. Hairpin cotter 2. Latch rod 3 4 4 Assembling the Bagger Top Parts needed for this procedure: 1 Bagger top 1 Bagger screen Procedure G005666 Figure 20 1. Turn the bagger top over. 2. Install the screen as shown in Figure 20 and that it slopes down toward the collection bags. 1. Bagger top 3. Screen tab 2. Screen 4. Slot in bagger top Note: Make sure that the screens snap into place and the tabs engage the bagger top.
PAGE 12
3. Slide the brackets over the posts and rotate the bagger top down to the operating position. 4. Lift the bagger top and install the bags by sliding the bag frame hooks onto the retaining brackets (Figure 22). Note: The bagger top is easier to install if 2 people work together. 1 1 2 2 4 3 Figure 22 3 4 5 1. Bag 3. Retaining bracket 2. Bagger frame 4. Bag frame hook 5. Lower the bagger top onto the bags (Figure 23). 6 G014888 Figure 21 1. Bagger top 4. Bracket, bagger top 2.
PAGE 13
6 1 2 Installing the Chute Parts needed for this procedure: 1 Cutoff baffle 1 Chute 3 Procedure 4 1. Lift up the grass deflector and locate the existing cutoff baffle. 5 G015221 Figure 25 2. Remove the locknuts and bolt securing the cutoff baffle to the underside of the mower deck (Figure 24). Retain all the fasteners. 1 1. Pivot rod 4. Nut (5/16 inch) 2. Bolt 3. Bagger-cutoff baffle 5. Locknut 4. Locate the chute in the loose parts.
PAGE 14
G015223 1 7 Connecting with the Discharge Tube Parts needed for this procedure: 1 Discharge tube Procedure 2 1. Slide the curved end of the discharge tube into the opening in the bagger top (Figure 28). Figure 27 1. Upper latch 2. Flexible latch 2 1 G010641 8. Secure the chute to the mower deck by hooking the flexible latch on the chute to the retaining clasp welded on the mower deck (Figure 27). 3 5 4 Figure 28 1. Discharge tube 4. Peg 2. Opening in bagger top 5. Rubber strap 3.
PAGE 15
8 9 Installing the Deck Ring Installing the Blade Parts needed for this procedure: Parts needed for this procedure: 4 Deck ring 8 Bolt (5/16 x 3/4 inch) 8 Locknut (5/16 inch) 1 Procedure 1. Remove the existing mower blade installed on your mower deck. Refer to the Removing the Blades section in the Operator's Manual for more information. Procedure 1. Install the interlocking deck rings to the bottom of the mower deck (Figure 29). 2. Install the Hi-Lift mower blade.
PAGE 16
Operation 1 Note: Determine the left and right sides of the machine from the normal operating position. WARNING To avoid personal injury, follow these procedures: • Become familiar with all operating and safety instructions in the Operator's Manual for the mower before using this attachment. 2 4 • Never remove the discharge tube, bags, bagger top, or the chute while the engine is running.
PAGE 17
Removing the Bagger CAUTION Failing to remove the front bagger weights and operating the machine without the bagger attachment may cause an unstable condition which could result in a loss of control. • Always remove the front weights when removing the bagger attachment. • If you remove the bagger attachment, remove the front weights. The bagger can be removed by repeating the Setup sections from all installed bagger related kits in reverse order.
PAGE 18
Operating Tips CAUTION As the bagger fills, extra weight is added to the back of the machine. If you stop and start suddenly on hills, you may lose steering control or the machine may tip. Tips for Bagging Remembering the Size • Do not start or stop suddenly when going uphill or downhill. Avoid uphill starts. Remember that the machine is longer and wider with this attachment installed. By turning too sharply in confined places you may damage the attachment.
PAGE 19
Maintenance Note: Determine the left and right sides of the machine from the normal operating position. Recommended Maintenance Schedule(s) Maintenance Service Interval Maintenance Procedure After the first 10 hours • Inspect the bagger. Before each use or daily Before storage • Clean the bagger. • Inspect the bagger. • Clean the bagger. CAUTION If you leave the key in the ignition switch, someone could accidently start the engine and seriously injure you or other bystanders.
PAGE 20
Cleaning the Bagger Attachment Storage Storing the Bagger Attachment Service Interval: Before each use or daily 1. Clean the bagger attachment; refer to Cleaning the Bagger Attachment (page 20). Before storage Note: To prevent rapid deterioration of the bag material, store the bags where they will dry completely after each use. 2. Inspect the bagger attachment for damage; refer to Inspecting the Bagger Attachment (page 19). 1.