FORM NO. 3322-166 Collector Drive for 60’’ Mower Model No. 79465-9900001 & Up Operator’s Manual IMPORTANT: Read this manual, and your tractor manual, carefully. They contain information about your safety and the safety of others. Also become familiar with the controls and their proper use before you operate the product.
Introduction We want you to be completely satisfied with your new product, so feel free to contact your local Authorized Service Dealer for help with service, genuine replacement parts, or other information you may require. Whenever you contact your Authorized Service Dealer or the factory, always know the model of your product. This number will help the Service Dealer or Service Representative provide exact information about your specific product.
Contents Page Safety and Instruction Decals .................................................................................. 2 Installation................................................................................................................ Loose Parts................................................................................................... Mower Preparation........................................................................................
Safety _______________________________________________________ Safety Decals and Safety Instructions Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or lost. (1) ON BOOT BRACKET (Part No. 93-7010) DANGER POTENTIAL HAZARD • Without the discharge chute or complete grass catcher assembly mounted in place, you and others are exposed to blade contact and thrown debris.
Installation Loose Parts Note: Use the chart below to identify parts used for assembly. DESCRIPTION Boot Assembly QTY. 1 USE Install on mower under discharge chute. Double Idler Assembly 1 Install on top of mower. V-Belt 1 Install on pulley. Double pulley 1 Install on right side mower spindle. Spacer 1 Install on leveller shaft. Idler Mounting Bracket 1 Install on top of mower. Stopper 2 Install on top of mower. Mower Baffle 1 Install under mower.
Installation _____________________________ Mower Preparation 2 Remove mower from tractor if installed. Refer to Operator’s Manual, section: Removing Mower. 1 1. Remove the belt guard on top of the right side spindle (Fig. 1). 2. Remove the V-belt (Fig. 1). 3. Remove the right side spindle pulley by unscrewing the spindle nut (Fig. 1). Figure 2 1. Double pulley 5. 1 4 3 Reinstall the mower belt as shown in Figure 3.
Installation 5. Leveler Stopper & Idler Mounting Bracket Installation On left side reinstall the bracket guide but with the leveler stopper underneath using the same bolt and nut (Fig. 5). 6. On right side install the idler mounting bracket with the leveler stopper underneath using the same bolts and nuts. Do not tighten yet (Fig. 5). 1. Remove the two flat leveler bars on right side and the rear leveler shaft from left leveler bars by removing bolts, pins and washers (Fig. 4). 2.
Installation Idler & Drive Belt Installation 7. Flip leveler shaft 180° and reinstall to left leveler bar. Shaft must be flipped to allow space for collector belt (Fig. 6). 1. 8. Slide the spacer on the leveler shaft on the right side (Fig. 6). 9. Reinstall the eye bolt and trunnion as dismounted but on the other side of the flat bar (right side) as shown (Fig. 6). Install the double idler assembly on the mounting bracket. Secure with cotter pin.
Installation Baffle Installation Mower Installation 1. Mark and drill hole of 13/32” dia. (10mm.) on the mower at the location shown in (Fig. 9). 1. 2. Remove the nut on the carriage bolt (Fig. 9). 3. Install the baffle under the mower and secure in place, one end to the carriage bolt and the other end to the holes you have drilled using a hex bolt 3/8 x 1” and flange nut. Install the mower on tractor as per Mower Operator’s Manual.
Installation Boot Installation 1. Install the boot on mower by lifting the mower discharge chute (do not remove it) and slide the boot bracket between the chute and the mower deck. Release the chute. It should lock the boot in place behind the cross bar (Fig. 11). See Collector set up for continued instructions. 2 4 5 3 1 Figure 11 1. Boot 2. Mower 3. Discharge chute ____ 8 4. Boot bracket 5.
Operation Read: Mower and Collector Operator’s Manuals operations sections. The operation of mower itself is the same with or without the collector drive. Baffles, idlers and belt can be left in place for side discharge operation. Maintenance Read: Mower and Collector Operator’s Manuals, maintenance sections. The maintenance on mower is the same with or without the collector drive except for the extra belt and idler inspection.
