Form No. 3408-757 Rev C Power Plex™ 40V MAX Standard Battery Pack/Charger Model No. 88525—Serial No. 317000001 and Up Model No. 88526—Serial No. 317000001 and Up Model No. 88527—Serial No. 317000001 and Up Register at www.Toro.com.
Safety IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE INSTRUCTIONS. Introduction This battery pack/charger is intended to be used by residential homeowners. Battery charger Model 88527 is designed to charge only battery pack Models 88525 and 88526. It is not designed to charge any other batteries. SAVE THESE INSTRUCTIONS – This manual contains important safety and operating instructions for battery pack Models 88525/88526 and battery charger Model 88527.
DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. DANGER Plugging the battery charger into an outlet that is not 240 V can cause fire or electric shock. • Do not plug the battery charger into an outlet other than 240 V. • Plug the power cord that matches your power outlets into the battery charger. CAUTION The battery pack may present a risk of fire or chemical burn if mistreated. • Do not disassemble the battery pack.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Symbol Designation/Explanation Class II For indoor use only Before charging, read the instructions decal136-2500 136-2500 Model 88526 Current fuse 1. Read the Operator’s Manual. 2. Do not burn the battery. Correct disposal of this product 3. Do not operate in wet conditions. 4. Do not discard.
decal136-2504 136-2504 1. The battery pack is charging. 3. The battery pack is too warm. 2. The battery pack is fully charged. 4. The battery pack needs to be replaced. decal136-2539 136–2539 1. Charge the battery where the temperature is between 0°C and 40°C (32°F and 104°F).
Setup Product Overview Mounting the Battery Charger (Optional) Specifications Battery Charger If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the charger. Model 88527 Type 40V MAX Lithium-Ion Battery Charger Mount it indoors (such as a garage or other dry place), near a power outlet, and out of the reach of children. Input 120 to 240V AC 50/60Hz Max 3.0A Output 41.8V MAX DC 2.5A Weight 1.0 kg (2.
Operation Charging the Battery Pack Important: The battery pack is not fully charged when it is purchased. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Make sure to read all safety precautions. Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 6).
Installing the Battery Pack Important: Operate the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 6). 1. Make sure that the vents on the battery are clear of any dust and debris. 2. Line up the cavity in the battery pack with the tongue on the tool. 3. Grasp the trigger handle. 4. Slide the battery pack into the tool until the battery locks into the latch (Figure 5). g194423 Figure 4 1. Charger venting areas 3. Right indicator light 2.
Maintenance Maintenance and servicing are not required under normal conditions. When you clean the surface of the equipment, wipe it off only with a dry cloth. Do not disassemble the equipment; if it is damaged, contact the supplier or manufacturer. Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 6).
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The flashlight does not turn on (battery pack Model 88526 only). Possible Cause 1. The battery pack is on the charger. 1. Remove the battery pack from the charger. 2. The battery pack is over or under the appropriate temperature range. 2.
Problem Possible Cause Corrective Action 1 LED indicator is blinking on the battery pack. 1. The battery pack voltage is low. 1. Place the battery pack on the charger. It is difficult to remove the battery pack from the tool. 1. The battery pack/tool is new or there is corrosion in the battery terminals and/or the terminals on the tool. 1. Clean the terminals on the battery pack and the tool.
Notes:
Notes:
Notes:
European Privacy Notice The Information Toro Collects Toro Warranty Company (Toro) respects your privacy. In order to process your warranty claim and contact you in the event of a product recall, we ask you to share certain personal information with us, either directly or through your local Toro company or dealer. The Toro warranty system is hosted on servers located within the United States where privacy law may not provide the same protection as applies in your country.
Residential Products The Toro Warranty and The Toro GTS Starting Guarantee Instructions for Obtaining Warranty Service Conditions and Products Covered The Toro Company and its affiliate, Toro Warranty Company, pursuant to an agreement between them, jointly promise to repair the Toro Product listed below if defective in materials or workmanship or if the Toro GTS (Guaranteed to Start) engine will not start on the first or second pull, provided the routine maintenance required in the Operator's Manual have
