Form No. 3417-974 Rev C PowerPlex™ 40V MAX Standard Battery Pack/Charger Model No. 88540—Serial No. 318000001 and Up Model No. 88541—Serial No. 318000001 and Up Model No. 88542—Serial No. 318000001 and Up Register at www.Toro.com.
Safety WARNING CALIFORNIA Proposition 65 Warning This product contains a chemical or chemicals known to the State of California to cause cancer, birth defects, or reproductive harm. IMPORTANT SAFETY INSTRUCTIONS—SAVE THESE INSTRUCTIONS. SAVE THESE INSTRUCTIONS—This manual contains important safety and operating instructions for battery pack Models 88540/88541 and battery charger Model 88542.
DANGER – TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, CAREFULLY FOLLOW THESE INSTRUCTIONS. DANGER Plugging the battery charger into an outlet that is not 120 V can cause fire or electric shock. • Do not plug the battery charger into an outlet other than 120 V. • For a foreign connection, use an attachment plug adapter of the proper configuration for the power outlet if needed. CAUTION The battery pack may present a risk of fire or chemical burn if mistreated. • Do not disassemble the battery pack.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. Symbol Designation/Explanation Class II For indoor use only Before charging, read the instructions Current fuse Correct disposal of this product This marking indicates that this battery charger and battery pack should not be disposed with other household wastes throughout the EU.
Setup Product Overview Mounting the Battery Charger (Optional) Specifications Battery Charger If desired, mount the battery charger securely on a wall using the wall-mount key holes on the back of the charger. Model 88542 Type 40V MAX Lithium-Ion Battery Charger Mount it indoors (such as a garage or other dry place), near a power outlet, and out of the reach of children. Input 100 to 120V AC 50/60Hz Max 3.0A Output 41.8V MAX DC 2.5A Refer to Figure 1 for assistance in mounting the charger.
Operation Charging the Battery Pack Important: The battery pack is not fully charged when you purchase it. Before using the tool for the first time, place the battery pack in the charger and charge it until the LED display indicates the battery pack is fully charged. Read all safety precautions. Important: Charge the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 5).
Installing the Battery Pack Important: Operate the battery pack only in temperatures that are within the appropriate range; refer to Specifications (page 5). 1. Make sure that the vents on the battery are clear of any dust and debris. 2. Line up the cavity in the battery pack with the tongue on the tool. 3. Grasp the trigger handle. 4. Slide the battery pack into the tool until the battery locks into the latch (Figure 5). g194423 Figure 4 1. Charger venting areas 3. Right indicator light 2.
Maintenance Maintenance and servicing are not required under normal conditions. When you clean the surface of the equipment, wipe it only with a dry cloth. Do not disassemble the equipment; if it is damaged, contact your Authorized Service Dealer. Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 5).
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The flashlight does not turn on (battery pack Model 88541 only). Possible Cause 1. The battery pack is on the charger. 1. Remove the battery pack from the charger. 2. The battery pack is over or under the appropriate temperature range. 2.
Problem Possible Cause Corrective Action 1 LED indicator is blinking on the battery pack. 1. The battery pack voltage is low. 1. Place the battery pack on the charger. It is difficult to remove the battery pack from the tool. 1. The battery pack/tool is new or there is corrosion in the battery terminals and/or the terminals on the tool. 1. Clean the terminals on the battery and the tool.