Form No. 3447-178 Rev A Stick Edger Attachment Flex-Force Power System™ 60V MAX String Trimmer Model No. 88710—Serial No. 321000001 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information. For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Safety 7. Charge the battery pack with only the battery charger specified by Toro. A charger suitable for 1 type of battery pack may create a risk of fire when used with another battery pack. 8. Charge the battery pack in a well-ventilated area only. 9. Do not expose a battery pack or battery charger to fire or to temperatures higher than 100°C (212°F). 10. Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions.
10. Do not overreach—Keep proper footing and balance at all times, especially on slopes. Walk, never run with the appliance. 7. Do not replace the existing non-metallic cutting means on the appliance with a metallic cutting means. 11. Stay alert—Watch what you are doing and use common sense when operating the appliance. Do not use the appliance while ill, tired, or under the influence of alcohol or drugs. 8. 12. Ensure that the ventilation openings are kept clear of debris.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal145-3134 145-3134 decal139-5210 139-5210 1. Warning—read the Operator’s Manual; stay away from moving parts; keep all guards in place; wear eye protection; do not operate in wet conditions.
Setup Connecting the Attachment to the Power Head 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of Figure 3). 3. The locking button clicks into the slotted hole when the shafts are secured (C of Figure 3). 4. Using the screw-handle, tighten the screw on the shaft connector until it is secure (D of Figure 3).
Specifications Product Overview Model 88710, attaches to 51832/T Blade Length 203 mm (8 inches) Rated Voltage 60V DC maximum, 54 VDC nominal usage No-load Max Speed 7000 rpm Weight (without battery pack) 4.6 kg (10.1 lbs) Appropriate Temperature Ranges Figure 4 2. Guard 3.
Operation Shutting Off the Edger Starting the Attachment To shut off the trimmer, release the run trigger (Figure 6). Allow at least 5 seconds for the blade to stop moving. 1. Ensure that the vents on the attachment, power head, and battery are clear of any dust and debris. 2. Align the cavity in the battery pack with the tongue on the handle housing (Figure 5). Whenever you are not using the edger or are transporting the edger to or from the work area, remove the battery pack.
Operating Tips Adjusting the Depth of Cut • Hold the edger with your right hand on the rear 1. Remove the battery from the edger. 2. Loosen the knob on the wheel and move it up or down in the track to increase or decrease the depth (Figure 8). handle and your left hand on the front handle. • Keep a firm grip with both hands while in operation. • The edger should be held at a comfortable position with the rear handle at about hip height.
Maintenance After each use of the edger, complete the following: 1. Remove the battery from the edger. 2. Wipe the edger clean with a damp cloth. Do not hose the edger down or submerge it in water. 3. Wipe or scrape clean the cutting head area any time there is an accumulation of debris. 4. Check and tighten all fasteners. If any part is damaged or lost, repair or replace it. 5. Brush debris away from air intake vents and exhaust on motor housing to prevent the motor from overheating.
Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 7). Important: If you are storing the battery pack for the off-season, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Notes:
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
