Form No. 3450-369 Rev B Flex-Force Power System™ 14in or 16in 60V MAX String Trimmer Flex-Force Power System™ 60V MAX Attachment Model No. 88716—Serial No. 321000001 and Up Register at www.Toro.com.
Important: With your mobile device, you can scan the QR code on the serial number decal (if equipped) to access warranty, parts, and other product information. For assistance, please see www.Toro.com/support for instructional videos or contact 1-888-384-9939 before returning this product. WARNING CALIFORNIA Proposition 65 Warning The power cord on this product contains lead, a chemical known to the State of California to cause birth defects or other reproductive harm. Wash hands after handling.
Safety The Model 51810T Power Head is compatible with a variety of Toro-approved attachments that, when combined, comply with specific standards; see the following table for more detail. Combination Power Head Model Attachment Standard Model String Trimmer 51810T 88716 Conforms to UL STD 82 Certified to CSA STD C22.2 No. 147 Edger 51810T 88710 Conforms to UL STD 82 Certified to CSA STD C22.2 No.
8. 9. 10. 11. 12. 1 type of battery pack may create a risk of fire when used with another battery pack. Charge the battery pack in a well-ventilated area only. Do not expose a battery pack or battery charger to fire or to temperatures higher than 100°C (212°F). Follow all charging instructions and do not charge the battery pack outside of the temperature range specified in the instructions. Otherwise, you may damage the battery pack and increase the risk of fire.
replacement parts to ensure that the product is safely maintained. 8. Store an idle appliance indoors in a place that is dry, secure, and out of the reach of children. 9. Do not dispose of the battery in a fire. The cell may explode. Check with local codes for possible special disposal instructions.
Safety and Instructional Decals Safety decals and instructions are easily visible to the operator and are located near any area of potential danger. Replace any decal that is damaged or missing. decal145-3141 145-3141 decal139-5210 139-5210 1. Warning—read the Operator’s Manual; stay away from moving parts; keep all guards in place; wear eye protection; do not operate in wet conditions.
Setup 1 Connecting the Attachment to the Power Head No Parts Required Procedure 1. Install the square shaft of the attachment into the square shaft of the power head (A of Figure 3). 2. Align the locking button on the lower shaft with the slotted hole on the upper shaft and slide the 2 shafts together (B and C of Figure 3). 3. The locking button clicks into the slotted hole when the shafts are secured (C of Figure 3). 4.
2 Installing the Guard Parts needed for this procedure: 1 Guard 4 Washer 4 Bolt Procedure 1. Align the trimmer guard beneath the guard mount as shown in Figure 4. g333216 Figure 4 3. Washer 4. Bolt 1. Guard mount 2. Trimmer guard 2. Secure the guard to the trimmer using the 4 washers and 4 bolts as shown in Figure 4.
Product Overview Operation Starting the Attachment 1. Ensure that the vents on the attachment, power head, and battery are clear of any dust and debris. 2. Align the cavity in the battery pack with the tongue on the handle housing (Figure 6). g372306 Figure 5 1. Guard 3. Bump button 2. String Specifications Model 88716, attaches to 51810T Charger Type 88610, 88602, or 88605 Battery Type 88620, 88625, 88640, 88650, 88660, or 88675 g357444 Figure 6 Appropriate Temperature Ranges 3.
Advancing the Line Using the Bump Feed Shutting Off the Trimmer To shut off the trimmer, release the trigger. Whenever you are not using the trimmer or are transporting the trimmer to or from the work area, remove the battery pack. Removing the Battery Pack from the Power Head 1. Run the trimmer at full throttle. 2. Tap the bump button on the ground to advance the line. The line advances each time the bump button is tapped. Do not hold the bump button on the ground.
Adjusting the Cutting Swath The trimmer comes from the factory with a cutting swath of 33 cm (13 inches) as shown in A of Figure 10. Refer to the following instructions to adjust the swath to 38.1 cm (15 inches) as shown in D of Figure 10. 1. Remove the swath blade from the bottom of the guard by removing the 2 screws holding it in place using the provided Allen wrench (B of Figure 10) and rotate the swath blade 180°. 2.
Maintenance After each use of the trimmer, complete the following: 1. Remove the battery from the power head. 2. Wipe the trimmer clean with a damp cloth. Do not hose the trimmer down or submerge it in water. CAUTION The line cutoff blade on the deflector is sharp and can cut you. Do not use your hands to clean the deflector shield and blade. 3. Wipe or scrape clean the cutting head area any time there is an accumulation of debris. 4. Check and tighten all fasteners.
Storage Important: Store the tool, battery pack, and charger only in temperatures that are within the appropriate range; refer to Specifications (page 9). Important: If you are storing the battery pack for the off-season, remove the battery pack from the tool and charge the battery pack until 2 or 3 LED indicators turn green on the battery. Do not store a fully charged or fully depleted battery.
Troubleshooting Perform only the steps described in these instructions. All further inspection, maintenance, and repair work must be performed by an authorized service center or a similarly qualified specialist if you cannot solve the problem yourself. Problem The tool does not start. Possible Cause Corrective Action 1. The battery is not fully installed in the tool. 1. Remove and then replace the battery into the tool, making sure that it is fully installed and latched. 2.
Notes:
California Proposition 65 Warning Information What is this warning? You may see a product for sale that has a warning label like the following: WARNING: Cancer and Reproductive Harm—www.p65Warnings.ca.gov. What is Prop 65? Prop 65 applies to any company operating in California, selling products in California, or manufacturing products that may be sold in or brought into California.
