Operator's Manual

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 92-6020

FORM NO. 3316-264

TPS

The Toro Company-1993

INSTALLATION

INSTRUCTIONS

ELECTRIC STARTER MOTOR KIT

(For 1990 CCR 1000 Electric Start Snowthrower Model No. 38195)

PART NO. 92-6020

Since this instruction sheet covers only a small portion of the information necessary to maintain and operate

your snowthrower, we suggest that you keep this material with your Operator's Manual so that both may be re

ferred to for instructions concerning safe operation and proper maintenance procedures.

INSTALLATION INSTRUCTIONS

1. Remove (2) two bolts from front of upper shroud

(Fig. 1).

Figure 1

1. Upper shroud 2. Bolt (2)

851

2. Remove (3) three carriage bolts securing dis

charge chute and chute handle to chute ring. Set

chute, handle and fasteners aside.

Figure 2

1. Discharge chute

2. Chute handle

3. Washer

4. Locknut

5. Carriage bolt

849

3. Remove (2) two screws from control panel

(Fig. 3) and allow panel to hang from recoil rope.

Figure 3

1. Control panel 2. Capscrew (2)

850

3. Gas cap

4. Remove gas cap (Fig. 3) and save.

5. Tilt front of shroud up toward handle.

6. Remove (3) three screws securing switch assem

bly to upper shroud (Fig. 4). Save screws for later

reinstallation.

1. Switch assembly 2. Screw (3)

852

3. Upper shroud

Figure 4

Summary of content (4 pages)

PAGE 1
FORM NO. 3316-264 INSTALLATION INSTRUCTIONS PART NO. 92-6020 ELECTRIC STARTER MOTOR KIT (For 1990 CCR 1000 Electric Start Snowthrower Model No. 38195) Since this instruction sheet covers only a small portion of the information necessary to maintain and operate your snowthrower, we suggest that you keep this material with your Operator's Manual so that both may be re ferred to for instructions concerning safe operation and proper maintenance procedures. INSTALLATION INSTRUCTIONS 1.
PAGE 2
INSTALLATION INSTRUCTIONS 7. Remove screw and r clamp (Fig. 5) and save for reinstallation. 9. Remove (3) three fasteners securing motor mounting bracket to engine. A 1 2 If bracket was secured to engine with studs and nuts (Fig. 7), remove (3) three nuts and bracket. Then remove right hand stud (nearest to flywheel) (Fig. 7) using a vise grip. 1 856 2 Figure 5 1. Screw 2. R-clamp 908 Figure 7 8. Remove (2) two screws securing starter motor to motor mounting bracket (Fig. 6).
PAGE 3
INSTALLATION INSTRUCTIONS 11. Install new motor mounting bracket (Fig. 9) with correct fasteners. For units with studs, you will need (2) two new / 20 nuts and a screw provided in kit. For units without studs, you will need (3) three new / 20 screws provided in kit. 14. Fasten wiring cable to engine with R-clamp and screw (Fig. 10), making sure wire routing clears the flywheel. 15. Attach new switch assembly using screws re moved from old switch assembly (Fig. 11). 2 1 3 1 852 Figure 11 910 1.
PAGE 4
OPERATING INSTRUCTIONS STARTING/STOPPING ENGINE (Fig. 13) 1. CONTROLS Key switch, primer, electric start button, and recoil starter are located on the control panel. The choke lever is just below the lower left corner of the control panel. 2 5 3 1 6 4 898 Figure 13 1. Key switch 2. Primer 3. Recoil start 4. Choke 5. Elec. start button* 6. Cord connection* *ELEC. START MODEL 2. Turn key to ON and move choke lever to ON (far right position). 3.