Installation Instructions

ManualsBrandsToro ManualsAttachmentsCE Kit for PA 17 Mounting Kit, Workman 3000

FORM NO. 93-6430 REV. A

MODEL NO. 93-9504

SET-UP AND

PARTS LIST

CE KIT FOR PA 17 MOUNTING KIT

FOR THE WORKMAN

3000 VEHICLE

Refer to the illustrated Parts catalog for the details of parts used in assembling the CE KIT.

©The TORO Company - 1999

1. Locate existing decals on Mounting Kit as

shown on the chart below.

2. Clean decal and surrounding area, making

sure it is free of dirt and grease.

3. Remove baking of replacement decal and apply

directly over existing decal and apply DIRECTLY

OVER existing decal, covering it completely.

4. Refer to FIG. 1 on page 3 for placement of new

decals.

Existing Decal Cover with New Decal

NO STEP

36-3400

NO RIDERS

75-5190

WARNING

ROTATING MEMBERS

80-8040

CAUTION

TO AVOID PERSONAL INJURY KEEP

ALL SHIELDS IN PLACE.

DISENGAGE AND SHUT OFF

ENGINE BEFORE SERVICING OR

UNCLOGGING MACHINE.

KEEP HANDS, FEET AND CLOTHING

AWAY FROM POWER-DRIVEN PARTS.

87-0450

Part No.93-9356

Part No.93-6687

Part No.93-6689

Part No.93-7814

Part No.94-3390Part No.87-0450

1-Located on top of Front Tube Crossmember

Part No.80-8040

2-Located on Radiator Cover,

1-Located on Belt Cover

Part No75-5190

1-Located on Rear Cover, 2-Located on sides of

Rear Support Tube, 2-Located on Radiator Cover.

Part No36-3400

2-Located on Radiator Cover

Part No.88-8950

2-Located on Frame under Belt Covers

Summary of content (8 pages)

PAGE 1
FORM NO. 93-6430 REV. A MODEL NO. 93-9504 SET-UP AND PARTS LIST CE KIT FOR PA 17 MOUNTING KIT ® FOR THE WORKMAN 3000 VEHICLE Refer to the illustrated Parts catalog for the details of parts used in assembling the CE KIT. 1. Locate existing decals on Mounting Kit as shown on the chart below. 2. Clean decal and surrounding area, making sure it is free of dirt and grease. 3.
PAGE 2
Existing Decal Cover with New Decal Part No. 92-2742 1-Located on rear of Hopper, under decal no. 92-2741 Part No.93-9088 READ YOUR OPERATOR’S MANUAL FOR OPERATING AND SAFETY INSTRUCTIONS. TO GET A REPLACEMENT MANUAL, SEND MODEL AND SERIAL NUMBERS TO : THE TORO CO., 8111 LYNDALE AVE. S., MPLS., MN 55420 65-3090 Part No. 65-3090 1-Located on top of Front Tube Crossmember Part No. 92-4366 2-Located on R.H. and L.H. side of Frame Part No. 92-4447 1-Located on Seat next to Spreader Lever Part No.
PAGE 3
Existing Decal Cover with New Decal WARNING TO AVOID INJURY FROM AGITATOR OSCILLATING INSIDE HOPPER DISENGAGE AND SHUT OFF ALL POWER BEFORE SERVICING OR UNCLOGGING AGITATOR. 87-0550 Part No.87-0550 2 Located on R.H. and L.H. sides of Hopper Part No. 93-9096 DANGER ENTANGLEMENT IN ROTATING DRIVELINE CAN CAUSE SERIOUS INJURY OR DEATH. KEEP ALL SHIELDS IN PLACE. AVOID CONTACT WITH ROTATING PARTS. 87-0560 Part No.87-0560 1-Located on front of Hopper Part No. 93-9097 Part No.
PAGE 4
SET-UP INSTRUCTIONS NOTE: The following procedure should be followed when installing both Cover Plates. 3. Drill two 7mm (9/32 in) holes at marked locations through Protection Casing. 1. Center Cover Plate over Adjust Hole in Protection Casing and, using it as a template, mark locations for holes to be drilled. 4. Install Cover Plate using two U-clips and hex washer head self-tapping screws. 2. Check to be sure that the center of holes to be drilled are NO MORE THAN 19mm (.75 in.
PAGE 5
1570 CE GUARD Part No. Description 1 322-7 HHCS, 5/16 x 1-1/2" 8 2 93-6441 Upper Arm Assembly, L.H. 1 3 93-6452 Carriage Bolt, 10mm x 30mm 4 4 93-6442 Upper Arm Assembly, R.H.
PAGE 6
PAGE 7
® 7
PAGE 8
® 8