Installation Instructions

ManualsBrandsToro ManualsAttachmentsCE Compliance Kit, Greens Aerator

FORM NO. 3318-535

The TORO Company - 1996

TPS

PART NO. 94-9100

CE COMPLIANCE KIT

INSTALLATION

INSTRUCTIONS

GREENS AERATOR

SAFETY AND INSTRUCTION DECALS

THE FOLLOWING DECALS AND GUARDS ARE TO BE INSTALLED ON THE

GREENS AERATOR. USE THE LOCATION DESCRIPTION LISTED BELOW

TO DETERMINE THE CORRECT PLACEMENT ON THE PRODUCT. BEFORE

INSTALLING DECALS, REMOVE OR THOROUGHLY CLEAN THE ENGLISH

DECAL, AND APPLY THE APPROPRIATE TRANSLATED LANGUAGE

VERSION IN ITS PLACE (OR OVER IT).

ONLY USE DECALS THAT REPLACE EXISTING DECALS ON MACHINE.

DISCARD UNUSED DECALS.

SHOULD ANY OF THESE DECALS OR GUARDS BECOME DAMAGED OR

ILLEGIBLE,REPLACE THEM IMMEDIATELY. EACH PART NUMBER IS

LISTED BELOW, AND ALSO ON EACH DECAL. REPLACEMENTS MAY BE

ORDERED THROUGH YOUR AUTHORIZED TORO DISTRIBUTOR.

ENGLISH PARTS

DESCRIPTION

LOCATION

ENGLISH

PART NO.

EUROPEAN

PART NO.

QTY.

Decal

C.E.

- - 93-7252 1

Decal

Danger

Coring Head Cover 59-9930 93-9884 1

Decal

Refueling

Fuel Tank 27-7310 93-7822 1

Decal

Shift

Air Cleaner Cover 66-9050 93-9887 1

Decal

Start

Air Cleaner Cover 66-9110 93-9888 1

Decal

Break-In

Fuel Tank 94-8076 93-9892 1

Decal

Danger

Battery 76-1660 93-7276 1

Decal

Battery Charging

Battery - 93-6668 1

Decal

Control

Control Panel 80-3910 93-9893 1

Decal

Brake

Control Handle 59-9860 93-9890 1

Decal

Interlock

Interlock Handle 59-9870 93-9891 2

Decal

Warning

Hood Supports - 94-2586 2

Summary of content (5 pages)

PAGE 1
FORM NO. 3318-535 PART NO. 94-9100 INSTALLATION INSTRUCTIONS CE COMPLIANCE KIT GREENS AERATOR SAFETY AND INSTRUCTION DECALS THE FOLLOWING DECALS AND GUARDS ARE TO BE INSTALLED ON THE GREENS AERATOR . USE THE LOCATION DESCRIPTION LISTED BELOW TO DETERMINE THE CORRECT PLACEMENT ON THE PRODUCT. BEFORE INSTALLING DECALS, REMOVE OR THOROUGHLY CLEAN THE ENGLISH DECAL, AND APPLY THE APPROPRIATE TRANSLATED LANGUAGE VERSION IN ITS PLACE (OR OVER IT). ONLY USE DECALS THAT REPLACE EXISTING DECALS ON MACHINE.
PAGE 2
ENGLISH PARTS DESCRIPTION LOCATION ENGLISH PART NO. EUROPEAN PART NO. QTY. Decal Warning Hood Supports - 94-2587 2 Decal Warning Pulley Guard 94-9111 93-6696 1 Decal Danger Frame Arms 67-5360 93-9883 2 Decal Danger Coring Head Frame 67-5360 93-9883 1 INSERT DECAL LOCATION SHEETS INTO OPERATOR'S MANUAL FOR OWNER'S REFERENCE. IMPORTANT The weighted RMS vibration level which the hands and arms are subject to while the engine is at full throttle and the coring head is engaged is 9.
PAGE 3
1 2 1 Figure 3 1. Side bracket 2. Hinge 3. Mount a hinge to each end of side rail with (2) 3/8-16 x 1" lg. capscrews and lockwashers (Fig. 3). 4. Mount the shield to inside front of R.H. hood support with (2) 5/16-18 x 3/4" lg. carriage bolts, flat washers and locknuts, as shown in figure 4. 2 Figure 5 1. R.H. hood support 7. Thread a knob onto each transport support lever. MODIFY CORING HEAD COVER 1 1. Remove idler pin from idler pin bracket.
PAGE 4
3. Modify the coring head cover (Fig. 7) using the following procedure: A. On front of cover, measure up 12" and scribe a line, A" to B", parallel to bottom edge. Dark line is scribed line. B. On side of cover, scribe a line from point B" to point on top of rear cutout, point C". D B E H 7. Secure front of coring head cover to hood support tabs with (2) 5/16-18 x 3/4" lg. carriage bolts, flatwashers and locknuts. 1 F 3 19-3/8" 2 G 12" Figure 9 A 1. Coring head cover 2. Hood support 3.
PAGE 5
3. Position hinged cover onto machine so mounting tab holes align with holes in left and right hood supports and rests on top of coring head cover (Fig. 11). 3. Reinstall control panel cover on machine. Secure front of cover to frame with a capscrew, lockwasher and flatwasher (Fig. 13). 1 1 Figure 13 1. Control panel cover REPLACE GAS CAP 1. Remove gas cap and replace with new cap. Figure 11 1. Hinged cover 1 4. Loosely secure hinged cover to left and right hood supports with (2) 3/8-16 x 3/4" lg.