Installation Instructions

ManualsBrandsToro ManualsAttachmentsCE Update Kit, Groundsmaster 580-D

Printed in the USA

W 2004, 2006 by The Toro Company

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

CE Update Kit

Groundsmaster

)

580–D

Part No. 94–9800

Form No. 3352–133 Rev A

Installation Instructions

SAFETY AND INSTRUCTION DECALS

THE FOLLOWING DECALS AND GUARDS ARE TO BE INSTALLED ON THE

GROUNDSMASTER 580D . USE THE LOCATION DESCRIPTION LISTED

BELOW TO DETERMINE THE CORRECT PLACEMENT ON THE PRODUCT.

BEFORE INSTALLING DECALS, REMOVE OR THOROUGHLY CLEAN THE

ENGLISH DECAL, AND APPLY THE APPROPRIATE TRANSLATED

LANGUAGE VERSION IN ITS PLACE

(OR OVER IT).

ONLY USE DECALS THAT REPLACE EXISTING DECALS ON MACHINE.

DISCARD UNUSED DECALS.

SHOULD ANY OF THESE DECALS OR GUARDS BECOME DAMAGED OR

ILLEGIBLE,REPLACE THEM IMMEDIATELY. EACH PART NUMBER IS

LISTED BELOW, AND ALSO ON EACH DECAL. REPLACEMENTS MAY BE

ORDERED THROUGH YOUR AUTHORIZED TORO DISTRIBUTOR.

Description Location

English Part

Number

European Part Number QTY.

Danger Decal Front Wheel 72–4070 95–0829 2

Danger Decal

Front and Rear of all

Decks

43–8480 106–6753 10

Danger Decal Top of Decks 67–5360 93–7273 6

Caution Decal

(Model 30581 only)

Floor Panel 69–0940 95–0823 1

Danger Decal

(Model 30582 & 30583)

Control Box 107–1159 107–1160 1

Display Decal Diagnostic Display 92–4087

95–0834 DANISH

95–0835 DUTCH

95–0836 FINNISH

95–0837 FRENCH

95–0838 GERMAN

95–0839 ITALIAN

95–0841 NORWEGIAN

95–0842 PORTUGUESE

95–0843 SPANISH

95–0844 SWEDISH

Hood Lock Decal Hood Back – 100–6574 1

Arrow Decal Hood Latch Handle – 94–6329 1

Danger Decal

Rear Fender and Frame

Front

72–4080 93–9371 2

Summary of content (8 pages)

PAGE 1
Form No. 3352–133 Rev A CE Update Kit Groundsmaster) 580–D Part No. 94–9800 Installation Instructions SAFETY AND INSTRUCTION DECALS THE FOLLOWING DECALS AND GUARDS ARE TO BE INSTALLED ON THE GROUNDSMASTER 580D . USE THE LOCATION DESCRIPTION LISTED BELOW TO DETERMINE THE CORRECT PLACEMENT ON THE PRODUCT. BEFORE INSTALLING DECALS, REMOVE OR THOROUGHLY CLEAN THE ENGLISH DECAL, AND APPLY THE APPROPRIATE TRANSLATED LANGUAGE VERSION IN ITS PLACE (OR OVER IT).
PAGE 2
Description Location English Part Number European Part Number QTY.
PAGE 3
Mount Deck Guard Bars Mount Valve Lever Stop 1. Mount a long guard bar and (2) short guard bars to front of center deck with 5/16–18 x 3/4” lg. capscrews. Position guards as shown in figure 1. 1. Remove (2) screws securing front of center control panel to chassis (Fig. 4). 1 2 1 Figure 4 Figure 1 1. Guard bar–long 1. Control panel 2. Guard bar–short (2) 2. Mount valve lever stop pivots to control panel with (2) 1/4–20 x 1–1/4” lg. socket head capscrews. Position as shown in figure 5. 2.
PAGE 4
Mount Hood Latch Assembly 8. Adjust latch plate and latch for proper engagement and tighten fasteners. 1. Follow directions on template (supplied with kit) to locate, mark and drill hood latch mounting holes in rear hood panel. Mount Pressure Switch Assemblies 2. Affix decal, to rear hood panel (Fig. 6). Position decal around newly drilled holes.
PAGE 5
2. Connect new hydraulic fitting w/O–ring to 90 and Tee fitting (Fig. 8). 2 3 8. At rear of bulkhead bracket, disconnect (2) lower left hydraulic hoses from hydraulic tubes (Fig. 10). fitting 2 1 3 1 4 Front of machine Figure 10 1. Bulkhead bracket 2. Hydraulic lines Figure 8 1. Hydraulic fitting 2. Pressure switch 3. Wiring harness 4. Ball switch location 3. Hydraulic tubes 9. Connect a new hydraulic fitting w/O–ring to each hydraulic tube. Position fittings as shown in figure 11. 3.
PAGE 6
2 2 1 1 Figure 12 1. Right wing lift arm 2. Ball switch Figure 14 1. Ball switch location 2. Harness 13. Connect new harness to ball switch and wire harness previously disconnected (Fig. 12, 13 & 14). Install Throttle Stop Use this procedure on traction unit models 30582 & 30583. 1. Remove cotter pin and clevis pin securing throttle rod clevis to throttle arm (Fig. 15). 4 2 3 Figure 13 14. Secure any loose wires with cable ties. 1 15. Check hydraulic fluid level and add fluid as required.
PAGE 7
4. Re–install throttle rod to throttle arm with clevis pin and cotter pin. 2. Loosen set screw on throttle stop. 3. Slide throttle stop onto high idle stop screw (Fig. 15). 5. Start engine and allow to run for 5 to 10 minutes. The engine must be at normal operating temperature before proceeding to next step. 4. Re–install adjusting lever/throttle arm to shaft with key. Tighten bolt. 5. Start engine and allow to run for 5 to 10 minutes.
PAGE 8