FORM NO. 3321–190 GTS 200 CONVERSION KIT For ProLine BBC Mowers Model Year 1992 and Up and For ProLine Zone Start Mowers Model Year 1995 and Up PART NO. 98–9230 PART NO. 98–9240 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify parts used for assembly. DESCRIPTION QTY. USE Discharge Chute 1 Latch Plate 1 Discharge Door Assembly 1 Door Retainer 1 Self-tapping Screw – 1/4-10 x .60 2 Screw – 3/8-16 x 1.
Installation DESCRIPTION QTY. Rope Guide (BBC models only) 1 Curved Washer (BBC models only) 1 Hex Head Screw – 1/4-20 x 1.5 (BBC models only) 1 Hex Lock Nut (BBC models only) 1 Before Installing USE Install new rope guide 3. Reconnect spark plug wire. 4. Even though the gasoline has been drained from the engine, enough fuel should be left in the carburetor bowl and fuel line to start the engine. Start the engine and let it run until it runs out of fuel.
Installation Remove Cable Ties 1. Cut cable ties holding cables to lower handle. Remove Gas Tank 1. Disconnect fuel line from engine (Fig. 2). 2. Remove gas tank from tank bracket (Fig. 2). Carefully set tank aside. 4 m-224 2 Figure 3 3 1. Belt cover 2. 2. Self-tapping screw (2) Loosen cable clamp screw and disconnect throttle cable from throttle lever (Fig. 4). 1 Figure 2 1. Fuel line clamp 2. Fuel line 3. Tank bracket 4. Gas tank Disconnect Throttle Cable 1.
Installation Disconnect Brake Cable (Zone Start Models Only) 1. Disconnect brake cable from brake arm (Fig. 5). 2. Using a pliers, squeeze tabs on top and bottom of brake cable fitting, and slide brake cable out of brake assembly (Fig. 5). 11 10 4 1 3 7 6 9 4 8 5 3 2 2 1 Figure 6 Figure 5 1. Brake cable 2. Brake arm 3. Brake cable fitting 4. Brake assembly Remove Blade Assembly Zone Start Models 1.
Installation 1 16 14 15 13 12 8 9 10 11 8 8 7 4 2 7 Figure 8 6 1. Engine 2. Engine screw (3) 5 Remove Discharge Tunnel Assembly (Fig. 9) 3 2 1 1. Remove (2) capscrews, (2) flat washers, (2) lock nuts, 1/2” hex head washer screw and 3/4” hex head washer screw securing discharge tunnel assembly to housing. Retain all of these items for reinstallation. 2. Lift off discharge tunnel assembly. 3. Remove spring bracket and spring extension. Retain these items for reinstallation. 4.
Installation 11 6 3. Install new discharge door assembly and secure with new door retainer. 4. Install new latch plate to tunnel using (2) new self-tapping screws. 5. Hook one end of spring extension through hole on spring bracket and the other end onto the discharge door handle. 6. Open and close discharge door to ensure that discharge tunnel door closes when handle is released. 12 8 9 1 10 2 3 5 7 4 Install New Engine 1. Carefully set new engine onto housing. 2.
Installation Reinstall Blade Assembly Install New Throttle Control Reinstall blade assembly in reverse order of disassembly. Refer to Remove Blade Assembly procedures. Zone Start Models Zone Start Models - When reinstalling crankshaft protector, install but do not tighten mounting screws. Insert a shim (a business card works well) between protector and hub on blade retainer which helps center protector. Tighten mounting screws and remove shim. Continue installing blade assembly.
Installation 6. 7. 8. 9. HP Models Only – Reconnect brake cable to throttle control using new E-ring. Then reconnect brake cable to engine (Fig. 5). SP Models Only – Reconnect traction cable to throttle control using new E-ring. Then reconnect brake cable to engine (Fig. 5). Make sure seals on cables are pushed down tight (Fig. 12). Route throttle cable across top of transmission (Fig. 13). 11. Move throttle to (FAST) position. 12. Push throttle arm to rear of engine as far as it will go. 13.
Installation 2. 3 Remove and discard old control panel decal. Install new control panel decal (Fig. 15). 4 2 3. Install new throttle control using (4) Phillips head screws and (4) lock nuts previously removed. Install new throttle control retainer. Note: Make sure seal on throttle cable is pushed down tight. 4. Connect throttle cable to throttle arm on engine. 5. Move throttle to 6. Push throttle arm to rear of engine as far as it will go. 7. 6 (FAST) position.
Installation Adjust Brake Cable 1 2 POTENTIAL HAZARD • BBC Models Only – Do not over–tighten blade brake cable. Over–tightening could cause blade brake to be pulled off brake drum. If brake does not contact drum, blade will not stop rotating when control bar is released. 3 4 6 WHAT CAN HAPPEN • A rotating blade could cause serious personal injury. HOW TO AVOID THE HAZARD • Check the blade brake mechanism each time brake cable is adjusted to ensure brake is stopping blade in 3 seconds or less.
Installation • BBC Models (Fig. 19) – Loosen cable clamp screw until brake cable conduit slides. Pull cable to remove slack, but do not put tension on spring. Tighten screw to lock adjustment in place. 2 6-8” 3 2 6 4 5 3 1 1 Figure 20 278 Figure 19 1. Spring 2. Cable clamp screw 3. Cable conduit Install Starter Rope in Rope Guide Zone Start Models 1. 4. Hex head capscrew 5. Curved washer 6. Hex lock nut 1. 9/32” hole 2. Control bar hole 3. Rope guide Install New Rope Stop 1.
Installation Install New Cable Ties 1. Reattach cables to lower handle using new cable ties. Install New Decals 1. Install new decals on engine (Fig. 22). 2 1 Figure 22 1. Decal P/N 84-4960 2. 2. Decal P/N 98-2002 Zone Start Self-propelled Model Only – Remove and discard old decal from control bar. Install new decal on control bar (Fig. 23). 1 Figure 23 1.
FORM NO 3321–190 KIT DE CONVERSIÓN GTS 200 Para las cortadoras de césped ProLine BBC del año 1992 y posteriores y para las cortadoras de césped ProLine Zone Start del año 1995 y posteriores REF. PIEZA 98–9230 REF. PIEZA 98–9240 INSTALACIÓN INSTRUCCIONES Piezas sueltas Nota: Utilice el cuadro siguiente para identificar las piezas que se utilizarán durante el montaje. DESCRIPCIÓN CANT.
Instalación DESCRIPCIÓN CANT. Guía para cuerda (modelos BBC únicamente) 1 Arandela curvada (modelos BBC únicamente) 1 Tornillo de cabeza hexagonal – 1/4-20 x 1.5 (modelos BBC únicamente) 1 Contratuerca hexagonal (modelos BBC únicamente) 1 Antes de la instalación 2. LO QUE PUEDE SUCEDER lesionar gravemente al operador o a los espectadores. 4.
Instalación Desmontaje de los componentes viejos Retire las ataduras para cables 1. Desmontaje de la cuerda de arranque 1. Modelos Zone Start únicamente – Desmonte la cuerda de arranque de la guía para cuerda (Fig. 1). Corte las ataduras para cables que sujetan los cables al manillar inferior. Desmontaje del depósito de combustible 1. Desconecte la línea de gasolina del motor (Fig. 2). 2. Desmonte el depósito de gasolina de su ménsula (Fig. 2). Coloque cuidadosamente el depósito a un lado.
Instalación Desconexión del cable del acelerador 1. Saque los (2) tornillos autorroscantes que sujetan la cubierta de la correa a la plataforma (Fig. 3). Coloque a un lado la cubierta y las piezas de sujeción para volver a utilizarlas más adelante. Desconexión del cable del freno (modelos Zone Start únicamente) 1. Desconecte el cable del freno del brazo del freno (Fig. 5). 2.
Instalación 16 14 11 15 13 10 12 8 9 7 6 9 4 8 10 11 8 5 8 7 7 3 4 6 5 2 1 Figura 6 1. Perno de la cuchilla 2. Arandela de seguridad 3. Refuerzo/acelerador de la cuchilla 4. Cuchilla 5. Retén de la cuchilla 6. Espaciador 7. Llave cuadrada 8. Tornillo autorroscante (3) 9. Arandela de seguridad interna (3) 10. Protector del cigüeñal 11. Polea de accionamiento del motor (modelo autopropulsado únicamente) Modelos BBC 1. 3 2 1 Figura 7 1. Tuerca de la cuchilla (2) 2. Cubeta antipelusa 3.
Instalación Desmontaje del motor viejo 1. 6 11 12 Saque los tres (3) tornillos del motor y levante éste cuidadosamente para sacarlo del alojamiento (Fig. 8). Deseche los tornillos y el motor. 8 9 1 1 10 2 3 7 5 4 2 Figura 9 Figura 8 1. Motor 2. Tornillo del motor (3) Desmontaje del conjunto del túnel de descarga (Fig. 9) 1.
Instalación y las (2) tuercas de seguridad desmontadas previamente. Sujete el lado delantero-derecho del túnel a la plataforma usando el tornillo de cabeza hexagonal con arandela de 1/2” retirado previamente. Sujete la esquina delanteraizquierda del túnel y la ménsula del muelle a la plataforma usando el tornillo de cabeza hexagonal con arandela de 3/4” retirado previamente. 3. Instale el nuevo conjunto de la puerta de descarga y sujételo con el nuevo retén de la puerta. 4.
Instalación Instalación de la guarda del cebador 1. 3. Saque los (2) tornillos de cabeza hexagonal del cuadrante delantero derecho (Fig. 11). Deje colocado el cuadrante. 2 Saque los (2) tornillos de cabeza hexagonal y las (2) arandelas curvadas que sujetan el control del acelerador al manillar (Fig. 12). Guarde los tornillos y las arandelas. Deseche el control del acelerador y el cable del acelerador. 3 1 1 6 4 3 5 Figura 11 1. Cuadrante delantero derecho 2. Tornillo de cabeza hexagonal (2) 2.
Instalación 8. Asegúrese de que las juntas de los cables están firmemente introducidas (Fig. 12). 9. Pase el cable del acelerador sobre la parte superior de la transmisión (Fig. 13). 13. Instale un tornillo y una abrazadera de cable nuevos en el motor (Fig. 14). Apriete el tornillo de la abrazadera para inmovilizar el cable del acelerador. 14. Vuelva a instalar la cubierta de la correa usando las piezas de sujeción que había retirado previamente (Fig. 3). Modelos BBC 1.
Instalación 2. Retire y deseche la vieja calcomanía del panel de control. Instale una nueva calcomanía en el panel de control (Fig. 15). 3. Instale el nuevo control del acelerador usando los (4) tornillos de cabeza Phillips y las (4) contratuercas que había retirado previamente. Instale el nuevo retén del control del acelerador. Nota: Conecte el cable del acelerador al brazo del acelerador del motor. 5. Coloque el acelerador en la posición RÁPIDO (FAST). 7. 3 2 2.
Instalación Ajuste del cable del freno PELIGRO POTENCIAL • Modelos BBC únicamente – No apriete excesivamente el cable del freno de la cuchilla. Si lo aprieta en exceso, el freno de la cuchilla podría salirse del tambor del freno. Si el freno no toca el tambor, cuando se suelta la barra de control la cuchilla seguirá girando. (3/16”–1/4”) entre la palanca del freno y el manillar. Tire hacia abajo del conducto del cable hasta que se elimine cualquier flojedad del alambre, y después apriete la tuerca.
Instalación • Modelos BBC (Fig. 19) - Afloje el tornillo de la ménsula del cable hasta que el conducto del cable del freno comience a deslizarse. Tire del cable para eliminar la flojedad, pero sin aplicar tensión en el muelle. Apriete el tornillo para bloquear el ajuste. 2 Modelos BBC 1. Taladre un orificio de 7 mm (9/32”), para pasar la guía para cuerda, a aproximadamente 15 – 20 cm (6–8”) por debajo del orificio de la barra de control (Fig. 20). 2.
Instalación Instalación del nuevo tope para cuerda 1. Coloque el tope alrededor de la cuerda de arranque a aproximadamente 5 cm de la abertura para el retroceso de la cuerda del motor (Fig. 21). 2 1 1 2” Figura 22 1. Calcomanía ref. pieza 84-4960 2. 2. Calcomanía ref. pieza 98-2002 Modelo autopropulsado Zone Start únicamente – Retire y deseche la vieja calcomanía de la barra de control. Instale la nueva calcomanía (Fig. 23). Figura 21 1 1.