Installation Instructions

ManualsBrandsToro ManualsAttachments, Parts & AccessoriesToro 99-0297



The T

oro Company – 1998

Printed in USA

FORM NO. 3322-419

INSTALLATION

INSTRUCTIONS

Part No. 99–0297

Enhancement Kit

Loose

Parts

Note: Use the chart below to identify parts for assembly.

DESCRIPTION QTY. USE

Remote Filter

Install Remote Filter Kit

Shear Bolt

Install Shear Bolt Kit

Left Hand Bagger Baf

fle

Right Hand Bagger Baf

fle

Install New Bagger Baf

fles

Left Hand Discharge Baf

fle

Right Hand Discharge Baf

fle

Install New Discharge Baf

fles

Left Hand Recycler Baf

fle

Right Hand Recycler Baf

fle

Install New Baf

fles for Recycler

Retainer Nuts

Hex Head Screws

Washers

Install New Retainer Nuts

Idler Arm Pivot Bolt

Install Idler Arm Pivot Bolt

Dampers 2

Install Dampers

Hopper Back Plate

Install Hopper Back Plate

Washers 3

Install new washer on hopper pegs

Rivets 4

Install new rivets

Washer 1

Install W

asher on Blower Pulley for 25hp Units

Summary of content (8 pages)

PAGE 1
FORM NO. 3322-419 Enhancement Kit Part No. 99–0297 INSTALLATION INSTRUCTIONS Loose Parts Note: Use the chart below to identify parts for assembly. DESCRIPTION QTY.
PAGE 2
Installation Instructions Installing Remote Filter Kit Installing New Discharge Baffles Refer to the enclosed kit and instructions for installing this kit. The discharge baffles are used in the bagging mode. When in bagging mode, you need to remove the old baffles in order to install new baffles. Installing Shear Bolt Kit Refer to the enclosed kit and instructions for installing this kit. Installing Baffles 1. Locate the left and right discharge baffles.
PAGE 3
Installation Instructions Installing New Baffles for Recycler 2. Remove baffles if not already done so. The recycler baffles are used in the recycling mode. When in recycling mode, you need to remove the old baffles in order to install new baffles. 3. On the top surface of the deck, install one retaining leg into the the square opening of the deck (Fig. 3 and 4). 1. 4. Push a screw driver into the other leg and insert retaining nut into square hole (Fig. 3). 5.
PAGE 4
Installation Instructions Installing New Idler Arm Pivot Bolt The new bolt will prevent the spring to go past bolt or center and loose tension on spring. Installing New Dampers The new dampers provide for less aggressive operation. This is useful for uneven terrain and new operators. The old dampers provide a more aggressive operation and experienced operators may prefer them. 1. Stop the engine, set the parking brake and remove the key. 1. Stop the engine, set the parking brake and remove the key.
PAGE 5
Installation Instructions Installing New Collection Bin Back Plate Installing New Washer on Collection Bin Pegs The new plates will increase support for the latches. The new washers will increase support for the latch pegs. 1. Unlatch and open rear lid on grass collection bin. 2. Remove existing bolts, washers and latch (Fig. 7). Note: It may be necessary to remove the bin flange in order to get proper access to bolts and washers (Fig. 7). 3. Discard the washers and replace with back plate.
PAGE 6
Installation Instructions Installing New Rivets on Grass Collection Bin Check to see if your metal chute is loose. If it is loose, replace the rivets. 1. Remove any existing rivets from metal chute (Fig. 9). 2. Install new rivets. (Fig. 9). Note: You may have to repeat actuation of a manual riveting tool until the mandrel breaks and rivet is set. 1 3 2 M–4240 Figure 9 1. Metal Chute 2. Rivets 6 3.
PAGE 7
Installation Instructions Installing New Washer on Blower Pulley Note: 3 This procedure is for mowers with 25hp engines only. 2 1. Stop the engine, set the parking brake and remove the key. 2. Push up and hold the spring loaded idler arm, behind blower to relax pressure on blower belt, and pin to engine frame (Fig. 11). m-4242 Figure 11 1. Screw 2. Washer 3. Remove belt (Fig. 11). 4. Loosen bolts that hold blower to frame (Fig. 10). Note: 1 4 3. Belt 4.
PAGE 8
Installation Instructions Tilting the Mower The mower can be tilted up for ease of service. 4. Standing in front of the mower, lift up and push rearward on front to raise mower (Fig. 13). 5. Raise mower until it contacts stops and latch pins snap into locked position. To Raise Mower 1. Turn engine off, set the parking brake and check that PTO cover is down against deck (Fig. 12). 2. Lift on the mower carrier frame to release weight on latch pin and pull out on latch pin to release (Fig. 12).