Sell Sheet

Greensmaster
®
TriFlex
TM
& TriFlex Hybrid Specifications
*
8-BlADE DPA CUTTiNG UNiTS, 04613 11-BlADE DPA CUTTiNG UNiTS, 04614 14-BlADE CUTTiNG UNiTS, 04615
TRACTOR
These cutting units will mount on the Greensmaster 3XXX series.
HEIGHT OF CUT
(HOC) RANGE
Cutting height is adjusted on front roller by two vertical screws and held by two locking cap screws. Bench HOC range is
.062"-.297" (1.6-7.5 mm). With high HOC kit, range is .285-1" (7.3-25.4 mm). Effective HOC may vary depending on turf
conditions and bedknife installed.
REEL WELDMENT
Reels are 5" (13 cm) in diameter, 21" (53.3 cm) in length. High carbon steel blades are welded to 5 stamped steel spiders, and heat treated to
RC 48-54 hardness. The reel is ground for diameter and concentricity, and backgrind.
REEL BEARINGS
Two stainless steel ball bearings, 30 +/-.1 mm inside diameter slip fit onto reel shaft retained by internally splined threaded insert. Low drag seals/slingers
for added protection with o-ring sealed motor and counterweight. Reel position maintained by a wave washer with no adjusting nut.
MAINTENANCE
No grease zerks, sealed bearing design eliminates daily maintenance.
REEL DRIVE
The reel weldment shaft is a 1.375" (35 mm) diameter tube with internally splined threaded insert.
FRAME
Precision machined, die-cast aluminum cross member with two bolt-on die-cast aluminum side plates.
AGGRESSIVENESS
Aggressiveness stays constant throughout the life of the reel. Patented design.
BEDKNIFE
Replaceable single edged, high carbon steel bedknife austempered to RC 55-58, fastened to a machined cast iron bedbar with 13 screws. EdgeMax
TM
Microcut Bedknife is standard on all cutting units.
BEDKNIFE ADJUSTMENT
Dual screw, indexed “click” adjustment to the reel; detents corresponding positively to .0007" (.018 mm) bedknife movement for
each position.
FRONT & REAR ROLLERS
Front: Aluminum Wiehle
®
, 2.5" (6.4 cm) diameter with sealed bearings and through-shaft. Option between full, narrow-spaced and
wide-spaced roller. Rear: Steel full, 2" (5.1 cm) diameter with sealed bearings and through-shaft.
GRASS SHIELD
Non-adjustable shield with adjustable cut-off bar to improve grass discharge from reel in wet conditions.
TOTAL WEIGHT
8-blade: 80 lbs. (30.4 kg) with aluminum Wiehle Roller. 11-blade: 83 lbs. (37.7 kg) with aluminum Wiehle Roller.
14-blade: 86 lbs. (39 kg) with aluminum Wiehle Roller.
*Specifications and design subject to change without notice. The Greensmaster TriFlex is manufactured in
Tomah, WI ISO 9002 Certified Plant.
TRiFlEx TRACTiON UNiT ACCESSORiES
04714 3WD Kit
04715 Leak Detector
04717 Light Kit
04718 Seat Kit, Standard
04719
Seat Kit, Premium
92-7307 Armrest Kit - Standard
119-710 5 Armrest Kit - Premium
119-1691 Hydraulic Oil Cooler Kit:Gas
117-9 314 Hydraulic Oil Cooler Kit: Diesel
119-7129
2WD Weight Kit (ANSI compliance)
120-5750 3WD Weight Kit (ANSI compliance)
104-6540 Spark Arrestor Kit (Gas)
120-1951 Spark Arrestor Kit (Diesel)
119-713 8 Dew Whip Holder
115- 4510 Canopy
119-1715 Utility Bag Kit
TRiFlEx DPA CUTTiNG UNiT ROllERS
04625 Full Roller DPA
04626 Narrow Wiehle Roller DPA
04627 Wide Wiehle Roller DPA
04628
Solid Steel Roller Kit (Front Wide
Wiehle, Rear Full)
04629 Anti Bobbing Roller - DPA (Front and Rear)
107-9561
Anti Bobbing Roller - Scraper Kit
(Front and Rear)
114 - 46 3 0 DPA Rear Roller Adjustment Kit
71-1550 2” Rear Wiehle Roller (cast iron)
112-9 294 Rear Roller Extension Kit
TBD
High Height of Cut Kit (.35 - .94)
TRiFlEx DPA CUTTiNG UNiTS
04613 8-Blade Cutting Unit
04614
11-Blade Cutting Unit
04615 14-Blade Cutting Unit
TRiFlEx DPA CUTTiNG UNiT ACCESSORiES
04710 Groomer Drive
04711 Groomer Reel, Carbide
04712 Groomer Reel, Spring Steel
04713 Groomer Brush
04724
Rotating Rear Roller Brush
115-188 0 EdgeMax Microcut Bedknife
115-1881 EdgeMax Tournament Bedknife
93-4262
Microcut Bedknife
(HOC Range 1.58mm - 3.18mm)
93-4263
Tournament Bedknife
(HOC Range 0.32mm - 6.35mm)
93-4264
Low Cut Bedknife
(HOC Range 6.35mm and higher)
94-6392 Bedknife – High Cut
108-4303 Extended Microcut Bedknife
108-4302
Extended Tournament Bedknife
63-8600 Bedknife – Fairway
99-3794-03
DPA Bedbar (aggressive – optional)
106-2648-01
DPA Bedbar (less aggressive –
standard equipment)
GREENSMASTER TRiFlEx ACCESSORiES