Sell Sheet

Groundsmaster
®
360 Specifications*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in design, required attachments and safety features. Consult your local Toro Distributor.
CUTTING DECK SPECIFIC ACCESSORIES FOR 72” SIDE DISCHARGE DECK (NON-CE)
RECYCLER KIT
Model 30347
LEAF MULCHING KIT
Part No. 108-5273
MEDIUM FLOW BLADE
Part No. 110-0621-03
HIGH FLOW BLADE
Part No. 110-0622-03
ATOMIC MULCHING BLADE
Part No. 110-0624-03
BLADE AND BELT KIT
Part No. 105-7272
CUTTING DECK SPECIFIC ACCESSORIES FOR 72” BASE DECK
COMPLETION KITS
(BLADES & BAFFLES)
72" Fine Cut Guardian recycler completion kit – Model 30346, 72" Guardian recycler completion Kit – Model 30304, 72" rear discharge completion kit – Model 30549
STANDARD BLADE
Part No. 108-1958
FLAT BLADE
(72” Rear Discharge Guardian Deck Only) Part No. 112-9586
TALL GRASS BAFFLE KIT
Improves cut of tall grass with seed heads. Part No. 105-7269
STANDARD BLADE & BELT KIT
Part No. 105-7271
GROUNDSMASTER 360 – 2WD
TIER 4 INTERIM DIESEL
MODELS 30534(N), 30536(N)
GROUNDSMASTER 360 – 4WD
TIER 4 INTERIM DIESEL
MODELS 30837(N), 30839(N)
GROUNDSMASTER 360 – CAB
TIER 4 INTERIM DIESEL
MODELS 30540(N), 30542(N)
100" CUTTING DECK, MODEL 31101
HEIGHT OF CUT
1”-5” (25 - 127 mm) adjustable in 0.25” (6 mm) increments
WIDTH OF CUT
100 in (254cm), by five blades
DECK CONSTRUCTION
Center deck with two wing decks; Welded .120" (11 gauge) high strength steel with steel .180" (7 gauge) stiffener plates and .1046" (12 gauge) chambers.
DISCHARGE
Rear Discharge – complete width of deck.
WING DECK ARTICULATION
15 degrees, up or down.
SPINDLE ASSEMBLY
Ductile cast iron 9" (23 cm) diameter conical spindle housing; Dual greaseable tapered roller bearings; Spindle shaft is 1.25" (3.2 cm) diameter, solid cold finished
steel, and splined connection between spindle shaft and pulley; Welded blade retainer plus anti-scalp cups.
CUTTER DRIVE
Isolation mounted, PTO driven gearbox with 1.25:1 spiral bevel gears. “B” section belt drive to all spindles.
BLADES
Wing Decks: 25.2" (64cm) long,.25" (6mm) thick, 2.5 (63mm) wide, heat treated steel blade in each wing; Center Deck: Three 18"(45.7cm) long, .25" (6mm) thick,
2.5" (63mm) wide, heat treated steel blades.
BLADE TIP SPEED
16,000 ± 1,000 ft/min at 3250 engine rpm
DECK SUSPENSION
Center deck is supported via 4 vertically suspended chains to the frame of the machine. Wing decks are supported by pin connections to center deck and castor
wheels on the ground. Hydraulic deck lift includes load holding check valves and gravity lower.
CASTOR WHEELS
Four 8 x 3.50-4, 4-ply, smooth, pneumatic, sealed precision ball bearings. Tensioning caps, made from impact modified thermoplastic alloy, are used to hold the castor wheels on the castor arms.
BELT IDLER
Fixed and spring loaded idlers.
DECK SKID
Replaceable, bolt-on, non-marking UHMW skid on both sides.
DECK ANTI-SCALP ROLLERS
5
ANTI-SCALP CUPS
Anti-scalp cup located on each blade spindle.
DECK COVERS
Steel and plastic with rubber latch connectors.
CUTTING DECK DEPTH
4.25" (108 mm)
WING DECK TRANSPORT LOCKS
Manual latches (standard)
WEIGHT
Approximately 790 lbs (358 kg)
WIDTH
Mow: 108" (274 cm) Transport: Overall width with wing decks raised: 88 in (223.5 cm); center deck is 54.5 in (138.4 cm) wide and 5" (12.7 cm) off ground when raised.
REQUIRED EQUIPMENT
Specific completion kit for each Groundsmaster 360 model with > 32hp engine. Check with Toro Distributor for details
OPTIONAL ACCESSORIES
Leaf Mulching Kit (Model 31105) Availiable in July 2014
CERTIFICATION
Cutting unit meets specification of American National Standard ANSI B71.4-2012, Safety Specifications for commercial turf care equipment. Cutting unit meets
specifications of European standard prEN836, CE approved.
MOWING RATE
Mow up to 8.0 acres/hr (3.2 hectare/hr) at 8 mph (12.9 km/hr). Assumes no overlap and 100% efficiency.
WARRANTY
Two year limited