Specifications

32
2015 Toro Commercial Equipment Guide 15-003-T Rev. 2/15
GROUNDSMASTER 7200 (30495) GROUNDSMASTER 7210 (30695)
ENGINE
Kubota,® 3-cylinder, liquid-cooled diesel. Power: 24.8 hp (18.5 kW) gross, at
rated speed of 3000 rpm. Torque peak: 52.7 ft. lbs. (71.5 Nm) @ 2200 rpm.
Displacement: 1123cc. High idle: 3200 rpm no load (uninstalled) 3100-3200
rpm installed. Remote mounted 5" Donaldson® air cleaner. Fuel filter/water
separator. EPA Tier IV Final Compliant.
Yanmar; 3-cylinder common-rail, liquid-cooled, diesel with EGR and diesel
particulate filter (DPF), 36.8hp (27.5 Kw) rated @ 3000 rpm, 80 ft-lbs @ 1950
rpm, High idle 3000 rpm, Low idle 1400 rpm, displacement 1642 cc. Remote
mounted Donaldson air filter, external spin-on oil filter and high flow fixed fan.
EPA Tier IV Final Compliant.
RADIATOR
Rear mount, cross flow, 6.5 fins per 1” (25 mm), 8 quart (7.6 liter) capacity
FUEL CAPACITY
11.5 gallons (43.5 liters), diesel. Biodiesel-Ready for use up to Kubota engine: B-20 (20% biodiesel and 80% petroleum blend); Yanmar engine: B-7 (7% biodiesel and
80% petroleum blend)
ENGINE OIL W/ FILTER
3.9 quarts (3.69 liter). 5.5 quarts (6.1 liter)
HYDRAULIC OIL
3.5 gallons (13.25 liter).
TRANSMISSION
Transmission directly mounted to engine via bell housing, two independent closed-loop circuits. One pump/motor controlling left side forward, neutral, and reverse, and
one pump/motor controlling right side forward, neutral, and reverse. Pumps are variable displacement piston type with slippers and full stroke capacity of 18cc/rev.
WHEEL DRIVE
Independent high-torque, low-speed wheel motors with 310cc displacement.
PTO CLUTCH
Hydraulically actuated wet multi-disc clutch.
STEERING CONTROL
Adjustable twin sticks with high performance KYB
®
hydraulic dampers. Rev/N/Forward, located on sides of operator.
GROUND SPEED
(MOWING CONFIGURATION)
Forward 0-12.5 mph (0-20 km/h), variable. Reverse 0-8.5 mph (0-13.7 km/h), variable.
ALTERNATOR/GENERATOR
12-volt, 40 amp internal regulated charging @ 3150 rpm. 12-volt, 55 amp internal regulated charging @ 3150 rpm.
BATTERY
BCI Group No.: 26, 540 cold cranking amps @ 0° F.
INSTRUMENTATION
Hour meter, glow indicator, high temp indicator, oil pressure indicator,
alternator indicator.
InfoCenter™: Onboard LCD display shows gauges, alerts/faults, service
reminders, electrical system diagnostics. Indicates, coolant temp, intake
temperature, low oil pressure, alternator, engine hours, engine rpm, hydraulic
oil temperature, voltage
SAFETY LOGIC CONTROLS
Toro Standard SCM.
INTERLOCKS
Tractor neutral, operator presence (engine shuts down if operator is not in seat and traction sticks are moved to the operation position), parking brake, PTO on,
auxiliary hydraulics on, high temp (PTO shuts down but engine still running), over temp (engine shuts down).
SERVICE BRAKE
Twin levers with dynamic braking through hydrostatic transmission.
PARKING BRAKE
Hand actuated brake lever with two 10.25" diameter disc brakes mounted on the rear wheel motors.
DRIVE TIRES
24 x12-12, 6-ply pneumatic tubeless, demountable and interchangeable. Tread “Toro Turf Tread”.
FRONT CASTOR TIRES
4-ply ribbed tread, tubeless 15 x 6-6, 20-22 psi.
ROLLOVER PROTECTION (ROPS)
Two-post foldable style ROPS certified per OSHA 1928.52 specification.
SEAT
Two piece, high back cushion seat with drain hole, deluxe low profile suspension, adjustable for operator weight, seat back angle, seat fore/aft position, lumbar
support and armrest height, retractable seat belt.
STORAGE
Built-in cup holder, and personal storage reached from seat. Storage for raingear, tools, etc.
IGNITION
Off/run/start, located right of operator.
THROTTLE
Low - high idle, located right of operator.
DECK HYDRAULIC LIFT
Raise/hold/lower/float; switch located on at end of right handle.
REAR HYDRAULIC LIFT
(OPTIONAL)
Raise/hold/lower/float. Electric switch right side of operator. Remote hydraulics selector switch, located on right console.
CURB CLIMBING
Capable of climbing 8" (20.3 cm) curbs.
TIE DOWNS
Four loops, one located on each corner of the machine.
FUEL ECONOMY**
TBD 1.1 gallons/hr (4.8 liters/hr)
CERTIFICATION
Cutting unit meets specification of American National Standard ANSI B71.4-2012, Safety Specifications for commercial turf care equipment. Cutting units sold in EU
meets specifications of European standard per ISO EN 5395
WARRANTY
2-year limited warranty. Refer to the Operator’s Manual for further details.
Groundsmaster
®
7200 Series Specifications
*
* Specifications and design subject to change without notice. Products depicted in this literature are for demonstration purposes only.
Actual products offered for sale may vary in use, design, required attachments and safety features. See distributor for details on all warranties.
The Groundsmaster
®
7200 and 7210 are manufactured
in Tomah, WI, ISO 9002 Certified Plant.